9174999628
Drop legacy ISA address support from the it87 driver. All supported chips are Super-I/O chips, so the device ISA address can be safely read from Super-I/O space rather than blindly assumed. Two nearby inaccurate documentation statements have been fixed as well: * The IT8705F doesn't have an SMBus interface. * The SiS950 doesn't have a distinct prefix. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
97 lines
4.1 KiB
Plaintext
97 lines
4.1 KiB
Plaintext
Kernel driver it87
|
|
==================
|
|
|
|
Supported chips:
|
|
* IT8705F
|
|
Prefix: 'it87'
|
|
Addresses scanned: from Super I/O config space (8 I/O ports)
|
|
Datasheet: Publicly available at the ITE website
|
|
http://www.ite.com.tw/
|
|
* IT8712F
|
|
Prefix: 'it8712'
|
|
Addresses scanned: I2C 0x28 - 0x2f
|
|
from Super I/O config space (8 I/O ports)
|
|
Datasheet: Publicly available at the ITE website
|
|
http://www.ite.com.tw/
|
|
* SiS950 [clone of IT8705F]
|
|
Prefix: 'it87'
|
|
Addresses scanned: from Super I/O config space (8 I/O ports)
|
|
Datasheet: No longer be available
|
|
|
|
Author: Christophe Gauthron <chrisg@0-in.com>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* update_vbat: int
|
|
|
|
0 if vbat should report power on value, 1 if vbat should be updated after
|
|
each read. Default is 0. On some boards the battery voltage is provided
|
|
by either the battery or the onboard power supply. Only the first reading
|
|
at power on will be the actual battery voltage (which the chip does
|
|
automatically). On other boards the battery voltage is always fed to
|
|
the chip so can be read at any time. Excessive reading may decrease
|
|
battery life but no information is given in the datasheet.
|
|
|
|
* fix_pwm_polarity int
|
|
|
|
Force PWM polarity to active high (DANGEROUS). Some chips are
|
|
misconfigured by BIOS - PWM values would be inverted. This option tries
|
|
to fix this. Please contact your BIOS manufacturer and ask him for fix.
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver implements support for the IT8705F, IT8712F and SiS950 chips.
|
|
|
|
This driver also supports IT8712F, which adds SMBus access, and a VID
|
|
input, used to report the Vcore voltage of the Pentium processor.
|
|
The IT8712F additionally features VID inputs.
|
|
|
|
These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
|
|
joysticks and other miscellaneous stuff. For hardware monitoring, they
|
|
include an 'environment controller' with 3 temperature sensors, 3 fan
|
|
rotation speed sensors, 8 voltage sensors, and associated alarms.
|
|
|
|
Temperatures are measured in degrees Celsius. An alarm is triggered once
|
|
when the Overtemperature Shutdown limit is crossed.
|
|
|
|
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
|
triggered if the rotation speed has dropped below a programmable limit. Fan
|
|
readings can be divided by a programmable divider (1, 2, 4 or 8) to give the
|
|
readings more range or accuracy. Not all RPM values can accurately be
|
|
represented, so some rounding is done. With a divider of 2, the lowest
|
|
representable value is around 2600 RPM.
|
|
|
|
Voltage sensors (also known as IN sensors) report their values in volts. An
|
|
alarm is triggered if the voltage has crossed a programmable minimum or
|
|
maximum limit. Note that minimum in this case always means 'closest to
|
|
zero'; this is important for negative voltage measurements. All voltage
|
|
inputs can measure voltages between 0 and 4.08 volts, with a resolution of
|
|
0.016 volt. The battery voltage in8 does not have limit registers.
|
|
|
|
The VID lines (IT8712F only) encode the core voltage value: the voltage
|
|
level your processor should work with. This is hardcoded by the mainboard
|
|
and/or processor itself. It is a value in volts.
|
|
|
|
If an alarm triggers, it will remain triggered until the hardware register
|
|
is read at least once. This means that the cause for the alarm may already
|
|
have disappeared! Note that in the current implementation, all hardware
|
|
registers are read whenever any data is read (unless it is less than 1.5
|
|
seconds since the last update). This means that you can easily miss
|
|
once-only alarms.
|
|
|
|
The IT87xx only updates its values each 1.5 seconds; reading it more often
|
|
will do no harm, but will return 'old' values.
|
|
|
|
To change sensor N to a thermistor, 'echo 2 > tempN_type' where N is 1, 2,
|
|
or 3. To change sensor N to a thermal diode, 'echo 3 > tempN_type'.
|
|
Give 0 for unused sensor. Any other value is invalid. To configure this at
|
|
startup, consult lm_sensors's /etc/sensors.conf. (2 = thermistor;
|
|
3 = thermal diode)
|
|
|
|
The fan speed control features are limited to manual PWM mode. Automatic
|
|
"Smart Guardian" mode control handling is not implemented. However
|
|
if you want to go for "manual mode" just write 1 to pwmN_enable.
|