android_kernel_xiaomi_sm8350/drivers/serial/crisv10.h
Alan Cox 606d099cdd [PATCH] tty: switch to ktermios
This is the grungy swap all the occurrences in the right places patch that
goes with the updates.  At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs

If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.

If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)

Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia

[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:57 -08:00

137 lines
3.9 KiB
C

/*
* serial.h: Arch-dep definitions for the Etrax100 serial driver.
*
* Copyright (C) 1998, 1999, 2000 Axis Communications AB
*/
#ifndef _ETRAX_SERIAL_H
#define _ETRAX_SERIAL_H
#include <linux/circ_buf.h>
#include <asm/termios.h>
/* Software state per channel */
#ifdef __KERNEL__
/*
* This is our internal structure for each serial port's state.
*
* Many fields are paralleled by the structure used by the serial_struct
* structure.
*
* For definitions of the flags field, see tty.h
*/
#define SERIAL_RECV_DESCRIPTORS 8
struct etrax_recv_buffer {
struct etrax_recv_buffer *next;
unsigned short length;
unsigned char error;
unsigned char pad;
unsigned char buffer[0];
};
struct e100_serial {
int baud;
volatile u8 *port; /* R_SERIALx_CTRL */
u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */
/* Output registers */
volatile u8 *oclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
volatile u32 *ofirstadr; /* adr to R_DMA_CHx_FIRST */
volatile u8 *ocmdadr; /* adr to R_DMA_CHx_CMD */
const volatile u8 *ostatusadr; /* adr to R_DMA_CHx_STATUS */
/* Input registers */
volatile u8 *iclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
volatile u32 *ifirstadr; /* adr to R_DMA_CHx_FIRST */
volatile u8 *icmdadr; /* adr to R_DMA_CHx_CMD */
volatile u32 *idescradr; /* adr to R_DMA_CHx_DESCR */
int flags; /* defined in tty.h */
u8 rx_ctrl; /* shadow for R_SERIALx_REC_CTRL */
u8 tx_ctrl; /* shadow for R_SERIALx_TR_CTRL */
u8 iseteop; /* bit number for R_SET_EOP for the input dma */
int enabled; /* Set to 1 if the port is enabled in HW config */
u8 dma_out_enabled:1; /* Set to 1 if DMA should be used */
u8 dma_in_enabled:1; /* Set to 1 if DMA should be used */
/* end of fields defined in rs_table[] in .c-file */
u8 uses_dma_in; /* Set to 1 if DMA is used */
u8 uses_dma_out; /* Set to 1 if DMA is used */
u8 forced_eop; /* a fifo eop has been forced */
int baud_base; /* For special baudrates */
int custom_divisor; /* For special baudrates */
struct etrax_dma_descr tr_descr;
struct etrax_dma_descr rec_descr[SERIAL_RECV_DESCRIPTORS];
int cur_rec_descr;
volatile int tr_running; /* 1 if output is running */
struct tty_struct *tty;
int read_status_mask;
int ignore_status_mask;
int x_char; /* xon/xoff character */
int close_delay;
unsigned short closing_wait;
unsigned short closing_wait2;
unsigned long event;
unsigned long last_active;
int line;
int type; /* PORT_ETRAX */
int count; /* # of fd on device */
int blocked_open; /* # of blocked opens */
struct circ_buf xmit;
struct etrax_recv_buffer *first_recv_buffer;
struct etrax_recv_buffer *last_recv_buffer;
unsigned int recv_cnt;
unsigned int max_recv_cnt;
struct work_struct work;
struct async_icount icount; /* error-statistics etc.*/
struct ktermios normal_termios;
struct ktermios callout_termios;
#ifdef DECLARE_WAITQUEUE
wait_queue_head_t open_wait;
wait_queue_head_t close_wait;
#else
struct wait_queue *open_wait;
struct wait_queue *close_wait;
#endif
unsigned long char_time_usec; /* The time for 1 char, in usecs */
unsigned long flush_time_usec; /* How often we should flush */
unsigned long last_tx_active_usec; /* Last tx usec in the jiffies */
unsigned long last_tx_active; /* Last tx time in jiffies */
unsigned long last_rx_active_usec; /* Last rx usec in the jiffies */
unsigned long last_rx_active; /* Last rx time in jiffies */
int break_detected_cnt;
int errorcode;
#ifdef CONFIG_ETRAX_RS485
struct rs485_control rs485; /* RS-485 support */
#endif
};
/* this PORT is not in the standard serial.h. it's not actually used for
* anything since we only have one type of async serial-port anyway in this
* system.
*/
#define PORT_ETRAX 1
/*
* Events are used to schedule things to happen at timer-interrupt
* time, instead of at rs interrupt time.
*/
#define RS_EVENT_WRITE_WAKEUP 0
#endif /* __KERNEL__ */
#endif /* !_ETRAX_SERIAL_H */