android_kernel_xiaomi_sm8350/drivers/ata/pata_cs5520.c
Bartlomiej Zolnierkiewicz 940a68de56 pata_cs5520: remove dead VDMA support
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.

Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:52:51 -05:00

325 lines
8.2 KiB
C

/*
* IDE tuning and bus mastering support for the CS5510/CS5520
* chipsets
*
* The CS5510/CS5520 are slightly unusual devices. Unlike the
* typical IDE controllers they do bus mastering with the drive in
* PIO mode and smarter silicon.
*
* The practical upshot of this is that we must always tune the
* drive for the right PIO mode. We must also ignore all the blacklists
* and the drive bus mastering DMA information. Also to confuse matters
* further we can do DMA on PIO only drives.
*
* DMA on the 5510 also requires we disable_hlt() during DMA on early
* revisions.
*
* *** This driver is strictly experimental ***
*
* (c) Copyright Red Hat Inc 2002
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2, or (at your option) any
* later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* Documentation:
* Not publically available.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_cs5520"
#define DRV_VERSION "0.6.6"
struct pio_clocks
{
int address;
int assert;
int recovery;
};
static const struct pio_clocks cs5520_pio_clocks[]={
{3, 6, 11},
{2, 5, 6},
{1, 4, 3},
{1, 3, 2},
{1, 2, 1}
};
/**
* cs5520_set_timings - program PIO timings
* @ap: ATA port
* @adev: ATA device
*
* Program the PIO mode timings for the controller according to the pio
* clocking table.
*/
static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int slave = adev->devno;
pio -= XFER_PIO_0;
/* Channel command timing */
pci_write_config_byte(pdev, 0x62 + ap->port_no,
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
/* FIXME: should these use address ? */
/* Read command timing */
pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
/* Write command timing */
pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
}
/**
* cs5520_set_piomode - program PIO timings
* @ap: ATA port
* @adev: ATA device
*
* Program the PIO mode timings for the controller according to the pio
* clocking table.
*/
static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
cs5520_set_timings(ap, adev, adev->pio_mode);
}
static struct scsi_host_template cs5520_sht = {
ATA_BMDMA_SHT(DRV_NAME),
.sg_tablesize = LIBATA_DUMB_MAX_PRD,
};
static struct ata_port_operations cs5520_port_ops = {
.inherits = &ata_bmdma_port_ops,
.qc_prep = ata_sff_dumb_qc_prep,
.cable_detect = ata_cable_40wire,
.set_piomode = cs5520_set_piomode,
};
static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.port_ops = &cs5520_port_ops,
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* IDE port enable bits */
pci_read_config_byte(pdev, 0x60, &pcicfg);
/* Check if the ATA ports are enabled */
if ((pcicfg & 3) == 0)
return -ENODEV;
ppi[0] = ppi[1] = &ata_dummy_port_info;
if (pcicfg & 1)
ppi[0] = &pi;
if (pcicfg & 2)
ppi[1] = &pi;
if ((pcicfg & 0x40) == 0) {
dev_printk(KERN_WARNING, &pdev->dev,
"DMA mode disabled. Enabling.\n");
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
}
pi.mwdma_mask = id->driver_data;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* Perform set up for DMA */
if (pci_enable_device_io(pdev)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
return -ENODEV;
}
if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
return -ENODEV;
}
/* Map IO ports and initialize host accordingly */
iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
return -ENOMEM;
ioaddr = &host->ports[0]->ioaddr;
ioaddr->cmd_addr = iomap[0];
ioaddr->ctl_addr = iomap[1];
ioaddr->altstatus_addr = iomap[1];
ioaddr->bmdma_addr = iomap[4];
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[0],
"cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
ioaddr = &host->ports[1]->ioaddr;
ioaddr->cmd_addr = iomap[2];
ioaddr->ctl_addr = iomap[3];
ioaddr->altstatus_addr = iomap[3];
ioaddr->bmdma_addr = iomap[4] + 8;
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[1],
"cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
/* activate the host */
pci_set_master(pdev);
rc = ata_host_start(host);
if (rc)
return rc;
for (i = 0; i < 2; i++) {
static const int irq[] = { 14, 15 };
struct ata_port *ap = host->ports[i];
if (ata_port_is_dummy(ap))
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
ata_sff_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
ata_port_desc(ap, "irq %d", irq[i]);
}
return ata_host_register(host, &cs5520_sht);
}
#ifdef CONFIG_PM
/**
* cs5520_reinit_one - device resume
* @pdev: PCI device
*
* Do any reconfiguration work needed by a resume from RAM. We need
* to restore DMA mode support on BIOSen which disabled it
*/
static int cs5520_reinit_one(struct pci_dev *pdev)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
u8 pcicfg;
int rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
pci_read_config_byte(pdev, 0x60, &pcicfg);
if ((pcicfg & 0x40) == 0)
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
ata_host_resume(host);
return 0;
}
/**
* cs5520_pci_device_suspend - device suspend
* @pdev: PCI device
*
* We have to cut and waste bits from the standard method because
* the 5520 is a bit odd and not just a pure ATA device. As a result
* we must not disable it. The needed code is short and this avoids
* chip specific mess in the core code.
*/
static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
int rc = 0;
rc = ata_host_suspend(host, mesg);
if (rc)
return rc;
pci_save_state(pdev);
return 0;
}
#endif /* CONFIG_PM */
/* For now keep DMA off. We can set it for all but A rev CS5510 once the
core ATA code can handle it */
static const struct pci_device_id pata_cs5520[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
{ },
};
static struct pci_driver cs5520_pci_driver = {
.name = DRV_NAME,
.id_table = pata_cs5520,
.probe = cs5520_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = cs5520_pci_device_suspend,
.resume = cs5520_reinit_one,
#endif
};
static int __init cs5520_init(void)
{
return pci_register_driver(&cs5520_pci_driver);
}
static void __exit cs5520_exit(void)
{
pci_unregister_driver(&cs5520_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pata_cs5520);
MODULE_VERSION(DRV_VERSION);
module_init(cs5520_init);
module_exit(cs5520_exit);