d6c3db83c5
On MPC8349E-mITX, MPC8315E-RDB and MPC837x-RDB boards there is a Freescale MC9S08QG8 (MCU) chip with the custom firmware pre-programmed. The chip is used to power-off the board by the software, and to control some GPIO pins. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
187 lines
6.2 KiB
Plaintext
187 lines
6.2 KiB
Plaintext
#
|
|
# Miscellaneous I2C chip drivers configuration
|
|
#
|
|
|
|
menu "Miscellaneous I2C Chip support"
|
|
|
|
config DS1682
|
|
tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
|
|
depends on EXPERIMENTAL
|
|
help
|
|
If you say yes here you get support for Dallas Semiconductor
|
|
DS1682 Total Elapsed Time Recorder.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called ds1682.
|
|
|
|
config AT24
|
|
tristate "EEPROMs from most vendors"
|
|
depends on SYSFS && EXPERIMENTAL
|
|
help
|
|
Enable this driver to get read/write support to most I2C EEPROMs,
|
|
after you configure the driver to know about each EEPROM on
|
|
your target board. Use these generic chip names, instead of
|
|
vendor-specific ones like at24c64 or 24lc02:
|
|
|
|
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
|
|
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
|
|
|
|
Unless you like data loss puzzles, always be sure that any chip
|
|
you configure as a 24c32 (32 kbit) or larger is NOT really a
|
|
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
|
|
as read-only won't help recover from this. Also, if your chip
|
|
has any software write-protect mechanism you may want to review the
|
|
code to make sure this driver won't turn it on by accident.
|
|
|
|
If you use this with an SMBus adapter instead of an I2C adapter,
|
|
full functionality is not available. Only smaller devices are
|
|
supported (24c16 and below, max 4 kByte).
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called at24.
|
|
|
|
config SENSORS_EEPROM
|
|
tristate "EEPROM reader"
|
|
depends on EXPERIMENTAL
|
|
help
|
|
If you say yes here you get read-only access to the EEPROM data
|
|
available on modern memory DIMMs and Sony Vaio laptops. Such
|
|
EEPROMs could theoretically be available on other devices as well.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called eeprom.
|
|
|
|
config SENSORS_PCF8574
|
|
tristate "Philips PCF8574 and PCF8574A (DEPRECATED)"
|
|
depends on EXPERIMENTAL && GPIO_PCF857X = "n"
|
|
default n
|
|
help
|
|
If you say yes here you get support for Philips PCF8574 and
|
|
PCF8574A chips. These chips are 8-bit I/O expanders for the I2C bus.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pcf8574.
|
|
|
|
This driver is deprecated and will be dropped soon. Use
|
|
drivers/gpio/pcf857x.c instead.
|
|
|
|
These devices are hard to detect and rarely found on mainstream
|
|
hardware. If unsure, say N.
|
|
|
|
config PCF8575
|
|
tristate "Philips PCF8575 (DEPRECATED)"
|
|
default n
|
|
depends on GPIO_PCF857X = "n"
|
|
help
|
|
If you say yes here you get support for Philips PCF8575 chip.
|
|
This chip is a 16-bit I/O expander for the I2C bus. Several other
|
|
chip manufacturers sell equivalent chips, e.g. Texas Instruments.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pcf8575.
|
|
|
|
This driver is deprecated and will be dropped soon. Use
|
|
drivers/gpio/pcf857x.c instead.
|
|
|
|
This device is hard to detect and is rarely found on mainstream
|
|
hardware. If unsure, say N.
|
|
|
|
config SENSORS_PCA9539
|
|
tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
|
|
depends on EXPERIMENTAL && GPIO_PCA953X = "n"
|
|
help
|
|
If you say yes here you get support for the Philips PCA9539
|
|
16-bit I/O port.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pca9539.
|
|
|
|
This driver is deprecated and will be dropped soon. Use
|
|
drivers/gpio/pca953x.c instead.
|
|
|
|
config SENSORS_PCF8591
|
|
tristate "Philips PCF8591"
|
|
depends on EXPERIMENTAL
|
|
default n
|
|
help
|
|
If you say yes here you get support for Philips PCF8591 chips.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pcf8591.
|
|
|
|
These devices are hard to detect and rarely found on mainstream
|
|
hardware. If unsure, say N.
|
|
|
|
config ISP1301_OMAP
|
|
tristate "Philips ISP1301 with OMAP OTG"
|
|
depends on ARCH_OMAP_OTG
|
|
help
|
|
If you say yes here you get support for the Philips ISP1301
|
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
|
The ISP1301 is used in products including H2 and H3 development
|
|
boards for Texas Instruments OMAP processors.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called isp1301_omap.
|
|
|
|
config TPS65010
|
|
tristate "TPS6501x Power Management chips"
|
|
depends on GPIOLIB
|
|
default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK
|
|
help
|
|
If you say yes here you get support for the TPS6501x series of
|
|
Power Management chips. These include voltage regulators,
|
|
lithium ion/polymer battery charging, and other features that
|
|
are often used in portable devices like cell phones and cameras.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called tps65010.
|
|
|
|
config SENSORS_MAX6875
|
|
tristate "Maxim MAX6875 Power supply supervisor"
|
|
depends on EXPERIMENTAL
|
|
help
|
|
If you say yes here you get support for the Maxim MAX6875
|
|
EEPROM-programmable, quad power-supply sequencer/supervisor.
|
|
|
|
This provides an interface to program the EEPROM and reset the chip.
|
|
|
|
This driver also supports the Maxim MAX6874 hex power-supply
|
|
sequencer/supervisor if found at a compatible address.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called max6875.
|
|
|
|
config SENSORS_TSL2550
|
|
tristate "Taos TSL2550 ambient light sensor"
|
|
depends on EXPERIMENTAL
|
|
help
|
|
If you say yes here you get support for the Taos TSL2550
|
|
ambient light sensor.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called tsl2550.
|
|
|
|
config MENELAUS
|
|
bool "TWL92330/Menelaus PM chip"
|
|
depends on I2C=y && ARCH_OMAP24XX
|
|
help
|
|
If you say yes here you get support for the Texas Instruments
|
|
TWL92330/Menelaus Power Management chip. This include voltage
|
|
regulators, Dual slot memory card tranceivers, real-time clock
|
|
and other features that are often used in portable devices like
|
|
cell phones and PDAs.
|
|
|
|
config MCU_MPC8349EMITX
|
|
tristate "MPC8349E-mITX MCU driver"
|
|
depends on I2C && PPC_83xx
|
|
select GENERIC_GPIO
|
|
select ARCH_REQUIRE_GPIOLIB
|
|
help
|
|
Say Y here to enable soft power-off functionality on the Freescale
|
|
boards with the MPC8349E-mITX-compatible MCU chips. This driver will
|
|
also register MCU GPIOs with the generic GPIO API, so you'll able
|
|
to use MCU pins as GPIOs.
|
|
|
|
endmenu
|