b187f180cc
early_serial_setup was removed from serial.h, but forgot to put in serial_8250.h Signed-off-by: Yinghai Lu <yinghai.lu@sun.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
235 lines
6.3 KiB
C
235 lines
6.3 KiB
C
/*
|
|
* Wind River SBC8560 board specific routines
|
|
*
|
|
* Maintainer: Kumar Gala
|
|
*
|
|
* Copyright 2004 Freescale Semiconductor Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*/
|
|
|
|
#include <linux/stddef.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/reboot.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/kdev_t.h>
|
|
#include <linux/major.h>
|
|
#include <linux/console.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/seq_file.h>
|
|
#include <linux/root_dev.h>
|
|
#include <linux/serial.h>
|
|
#include <linux/tty.h> /* for linux/serial_core.h */
|
|
#include <linux/serial_core.h>
|
|
#include <linux/serial_8250.h>
|
|
#include <linux/initrd.h>
|
|
#include <linux/module.h>
|
|
#include <linux/fsl_devices.h>
|
|
|
|
#include <asm/system.h>
|
|
#include <asm/pgtable.h>
|
|
#include <asm/page.h>
|
|
#include <asm/atomic.h>
|
|
#include <asm/time.h>
|
|
#include <asm/io.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/open_pic.h>
|
|
#include <asm/bootinfo.h>
|
|
#include <asm/pci-bridge.h>
|
|
#include <asm/mpc85xx.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/immap_85xx.h>
|
|
#include <asm/kgdb.h>
|
|
#include <asm/ppc_sys.h>
|
|
#include <mm/mmu_decl.h>
|
|
|
|
#include <syslib/ppc85xx_common.h>
|
|
#include <syslib/ppc85xx_setup.h>
|
|
|
|
#ifdef CONFIG_SERIAL_8250
|
|
static void __init
|
|
sbc8560_early_serial_map(void)
|
|
{
|
|
struct uart_port uart_req;
|
|
|
|
/* Setup serial port access */
|
|
memset(&uart_req, 0, sizeof (uart_req));
|
|
uart_req.irq = MPC85xx_IRQ_EXT9;
|
|
uart_req.flags = STD_COM_FLAGS;
|
|
uart_req.uartclk = BASE_BAUD * 16;
|
|
uart_req.iotype = UPIO_MEM;
|
|
uart_req.mapbase = UARTA_ADDR;
|
|
uart_req.membase = ioremap(uart_req.mapbase, MPC85xx_UART0_SIZE);
|
|
uart_req.type = PORT_16650;
|
|
|
|
#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
|
|
gen550_init(0, &uart_req);
|
|
#endif
|
|
|
|
if (early_serial_setup(&uart_req) != 0)
|
|
printk("Early serial init of port 0 failed\n");
|
|
|
|
/* Assume early_serial_setup() doesn't modify uart_req */
|
|
uart_req.line = 1;
|
|
uart_req.mapbase = UARTB_ADDR;
|
|
uart_req.membase = ioremap(uart_req.mapbase, MPC85xx_UART1_SIZE);
|
|
uart_req.irq = MPC85xx_IRQ_EXT10;
|
|
|
|
#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
|
|
gen550_init(1, &uart_req);
|
|
#endif
|
|
|
|
if (early_serial_setup(&uart_req) != 0)
|
|
printk("Early serial init of port 1 failed\n");
|
|
}
|
|
#endif
|
|
|
|
/* ************************************************************************
|
|
*
|
|
* Setup the architecture
|
|
*
|
|
*/
|
|
static void __init
|
|
sbc8560_setup_arch(void)
|
|
{
|
|
bd_t *binfo = (bd_t *) __res;
|
|
unsigned int freq;
|
|
struct gianfar_platform_data *pdata;
|
|
struct gianfar_mdio_data *mdata;
|
|
|
|
/* get the core frequency */
|
|
freq = binfo->bi_intfreq;
|
|
|
|
if (ppc_md.progress)
|
|
ppc_md.progress("sbc8560_setup_arch()", 0);
|
|
|
|
/* Set loops_per_jiffy to a half-way reasonable value,
|
|
for use until calibrate_delay gets called. */
|
|
loops_per_jiffy = freq / HZ;
|
|
|
|
#ifdef CONFIG_PCI
|
|
/* setup PCI host bridges */
|
|
mpc85xx_setup_hose();
|
|
#endif
|
|
#ifdef CONFIG_SERIAL_8250
|
|
sbc8560_early_serial_map();
|
|
#endif
|
|
#ifdef CONFIG_SERIAL_TEXT_DEBUG
|
|
/* Invalidate the entry we stole earlier the serial ports
|
|
* should be properly mapped */
|
|
invalidate_tlbcam_entry(num_tlbcam_entries - 1);
|
|
#endif
|
|
|
|
/* setup the board related info for the MDIO bus */
|
|
mdata = (struct gianfar_mdio_data *) ppc_sys_get_pdata(MPC85xx_MDIO);
|
|
|
|
mdata->irq[25] = MPC85xx_IRQ_EXT6;
|
|
mdata->irq[26] = MPC85xx_IRQ_EXT7;
|
|
mdata->irq[31] = PHY_POLL;
|
|
|
|
/* setup the board related information for the enet controllers */
|
|
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC1);
|
|
if (pdata) {
|
|
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
|
|
pdata->bus_id = 0;
|
|
pdata->phy_id = 25;
|
|
memcpy(pdata->mac_addr, binfo->bi_enetaddr, 6);
|
|
}
|
|
|
|
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC2);
|
|
if (pdata) {
|
|
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
|
|
pdata->bus_id = 0;
|
|
pdata->phy_id = 26;
|
|
memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
|
|
}
|
|
|
|
#ifdef CONFIG_BLK_DEV_INITRD
|
|
if (initrd_start)
|
|
ROOT_DEV = Root_RAM0;
|
|
else
|
|
#endif
|
|
#ifdef CONFIG_ROOT_NFS
|
|
ROOT_DEV = Root_NFS;
|
|
#else
|
|
ROOT_DEV = Root_HDA1;
|
|
#endif
|
|
}
|
|
|
|
/* ************************************************************************ */
|
|
void __init
|
|
platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
|
|
unsigned long r6, unsigned long r7)
|
|
{
|
|
/* parse_bootinfo must always be called first */
|
|
parse_bootinfo(find_bootinfo());
|
|
|
|
/*
|
|
* If we were passed in a board information, copy it into the
|
|
* residual data area.
|
|
*/
|
|
if (r3) {
|
|
memcpy((void *) __res, (void *) (r3 + KERNELBASE),
|
|
sizeof (bd_t));
|
|
}
|
|
|
|
#ifdef CONFIG_SERIAL_TEXT_DEBUG
|
|
/* Use the last TLB entry to map CCSRBAR to allow access to DUART regs */
|
|
settlbcam(num_tlbcam_entries - 1, UARTA_ADDR,
|
|
UARTA_ADDR, 0x1000, _PAGE_IO, 0);
|
|
#endif
|
|
|
|
#if defined(CONFIG_BLK_DEV_INITRD)
|
|
/*
|
|
* If the init RAM disk has been configured in, and there's a valid
|
|
* starting address for it, set it up.
|
|
*/
|
|
if (r4) {
|
|
initrd_start = r4 + KERNELBASE;
|
|
initrd_end = r5 + KERNELBASE;
|
|
}
|
|
#endif /* CONFIG_BLK_DEV_INITRD */
|
|
|
|
/* Copy the kernel command line arguments to a safe place. */
|
|
|
|
if (r6) {
|
|
*(char *) (r7 + KERNELBASE) = 0;
|
|
strcpy(cmd_line, (char *) (r6 + KERNELBASE));
|
|
}
|
|
|
|
identify_ppc_sys_by_id(mfspr(SPRN_SVR));
|
|
|
|
/* setup the PowerPC module struct */
|
|
ppc_md.setup_arch = sbc8560_setup_arch;
|
|
ppc_md.show_cpuinfo = sbc8560_show_cpuinfo;
|
|
|
|
ppc_md.init_IRQ = sbc8560_init_IRQ;
|
|
ppc_md.get_irq = openpic_get_irq;
|
|
|
|
ppc_md.restart = mpc85xx_restart;
|
|
ppc_md.power_off = mpc85xx_power_off;
|
|
ppc_md.halt = mpc85xx_halt;
|
|
|
|
ppc_md.find_end_of_memory = mpc85xx_find_end_of_memory;
|
|
|
|
ppc_md.time_init = NULL;
|
|
ppc_md.set_rtc_time = NULL;
|
|
ppc_md.get_rtc_time = NULL;
|
|
ppc_md.calibrate_decr = mpc85xx_calibrate_decr;
|
|
|
|
#if defined(CONFIG_SERIAL_8250) && defined(CONFIG_SERIAL_TEXT_DEBUG)
|
|
ppc_md.progress = gen550_progress;
|
|
#endif /* CONFIG_SERIAL_8250 && CONFIG_SERIAL_TEXT_DEBUG */
|
|
#if defined(CONFIG_SERIAL_8250) && defined(CONFIG_KGDB)
|
|
ppc_md.early_serial_map = sbc8560_early_serial_map;
|
|
#endif /* CONFIG_SERIAL_8250 && CONFIG_KGDB */
|
|
|
|
if (ppc_md.progress)
|
|
ppc_md.progress("sbc8560_init(): exit", 0);
|
|
}
|