lisa/android_kernel_xiaomi_sm8350
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
e816056210
android_kernel_xiaomi_sm8350/drivers/ide/pci/siimage.c
Sergei Shtylyov 8ac98ce17c siimage: remove resetproc() method 
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-11-27 21:35:53 +01:00

911 lines
23 KiB
C
Raw Blame History

/*
* linux/drivers/ide/pci/siimage.c Version 1.19 Nov 16 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
* Copyright (C) 2007 MontaVista Software, Inc.
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*
* May be copied or modified under the terms of the GNU General Public License
*
* Documentation for CMD680:
* http://gkernel.sourceforge.net/specs/sii/sii-0680a-v1.31.pdf.bz2
*
* Documentation for SiI 3112:
* http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2
*
* Errata and other documentation only available under NDA.
*
*
* FAQ Items:
* If you are using Marvell SATA-IDE adapters with Maxtor drives
* ensure the system is set up for ATA100/UDMA5 not UDMA6.
*
* If you are using WD drives with SATA bridges you must set the
* drive to "Single". "Master" will hang
*
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
* if necessary
*
* The Dell DRAC4 has some interesting features including effectively hot
* unplugging/replugging the virtual CD interface when the DRAC is reset.
* This often causes drivers/ide/siimage to panic but is ok with the rather
* smarter code in libata.
*
* TODO:
* - IORDY fixes
* - VDMA support
*/
#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
/**
* pdev_is_sata - check if device is SATA
* @pdev: PCI device to check
*
* Returns true if this is a SATA controller
*/
static int pdev_is_sata(struct pci_dev *pdev)
{
#ifdef CONFIG_BLK_DEV_IDE_SATA
switch(pdev->device) {
case PCI_DEVICE_ID_SII_3112:
case PCI_DEVICE_ID_SII_1210SA:
return 1;
case PCI_DEVICE_ID_SII_680:
return 0;
}
BUG();
#endif
return 0;
}
/**
* is_sata - check if hwif is SATA
* @hwif: interface to check
*
* Returns true if this is a SATA controller
*/
static inline int is_sata(ide_hwif_t *hwif)
{
return pdev_is_sata(hwif->pci_dev);
}
/**
* siimage_selreg - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* Thankfully this is a configuration operation so isnt performance
* criticial.
*/
static unsigned long siimage_selreg(ide_hwif_t *hwif, int r)
{
unsigned long base = (unsigned long)hwif->hwif_data;
base += 0xA0 + r;
if(hwif->mmio)
base += (hwif->channel << 6);
else
base += (hwif->channel << 4);
return base;
}
/**
* siimage_seldev - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* including accounting for the unit shift.
*/
static inline unsigned long siimage_seldev(ide_drive_t *drive, int r)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = (unsigned long)hwif->hwif_data;
base += 0xA0 + r;
if(hwif->mmio)
base += (hwif->channel << 6);
else
base += (hwif->channel << 4);
base |= drive->select.b.unit << drive->select.b.unit;
return base;
}
/**
* sil_udma_filter - compute UDMA mask
* @drive: IDE device
*
* Compute the available UDMA speeds for the device on the interface.
*
* For the CMD680 this depends on the clocking mode (scsc), for the
* SI3112 SATA controller life is a bit simpler.
*/
static u8 sil_pata_udma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long base = (unsigned long) hwif->hwif_data;
u8 mask = 0, scsc = 0;
if (hwif->mmio)
scsc = hwif->INB(base + 0x4A);
else
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
if ((scsc & 0x30) == 0x10) /* 133 */
mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x20) /* 2xPCI */
mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x00) /* 100 */
mask = ATA_UDMA5;
else /* Disabled ? */
BUG();
return mask;
}
static u8 sil_sata_udma_filter(ide_drive_t *drive)
{
return strstr(drive->id->model, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6;
}
/**
* sil_set_pio_mode - set host controller for PIO mode
* @drive: drive
* @pio: PIO mode number
*
* Load the timing settings for this device mode into the
* controller. If we are in PIO mode 3 or 4 turn on IORDY
* monitoring (bit 9). The TF timing is bits 31:16
*/
static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
{
const u16 tf_speed[] = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
ide_hwif_t *hwif = HWIF(drive);
ide_drive_t *pair = ide_get_paired_drive(drive);
u32 speedt = 0;
u16 speedp = 0;
unsigned long addr = siimage_seldev(drive, 0x04);
unsigned long tfaddr = siimage_selreg(hwif, 0x02);
unsigned long base = (unsigned long)hwif->hwif_data;
u8 tf_pio = pio;
u8 addr_mask = hwif->channel ? (hwif->mmio ? 0xF4 : 0x84)
: (hwif->mmio ? 0xB4 : 0x80);
u8 mode = 0;
u8 unit = drive->select.b.unit;
/* trim *taskfile* PIO to the slowest of the master/slave */
if (pair->present) {
u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
if (pair_pio < tf_pio)
tf_pio = pair_pio;
}
/* cheat for now and use the docs */
speedp = data_speed[pio];
speedt = tf_speed[tf_pio];
if (hwif->mmio) {
hwif->OUTW(speedp, addr);
hwif->OUTW(speedt, tfaddr);
/* Now set up IORDY */
if (pio > 2)
hwif->OUTW(hwif->INW(tfaddr-2)|0x200, tfaddr-2);
else
hwif->OUTW(hwif->INW(tfaddr-2)&~0x200, tfaddr-2);
mode = hwif->INB(base + addr_mask);
mode &= ~(unit ? 0x30 : 0x03);
mode |= (unit ? 0x10 : 0x01);
hwif->OUTB(mode, base + addr_mask);
} else {
pci_write_config_word(hwif->pci_dev, addr, speedp);
pci_write_config_word(hwif->pci_dev, tfaddr, speedt);
pci_read_config_word(hwif->pci_dev, tfaddr-2, &speedp);
speedp &= ~0x200;
/* Set IORDY for mode 3 or 4 */
if (pio > 2)
speedp |= 0x200;
pci_write_config_word(hwif->pci_dev, tfaddr-2, speedp);
pci_read_config_byte(hwif->pci_dev, addr_mask, &mode);
mode &= ~(unit ? 0x30 : 0x03);
mode |= (unit ? 0x10 : 0x01);
pci_write_config_byte(hwif->pci_dev, addr_mask, mode);
}
}
/**
* sil_set_dma_mode - set host controller for DMA mode
* @drive: drive
* @speed: DMA mode
*
* Tune the SiI chipset for the desired DMA mode.
*/
static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
u16 dma[] = { 0x2208, 0x10C2, 0x10C1 };
ide_hwif_t *hwif = HWIF(drive);
u16 ultra = 0, multi = 0;
u8 mode = 0, unit = drive->select.b.unit;
unsigned long base = (unsigned long)hwif->hwif_data;
u8 scsc = 0, addr_mask = ((hwif->channel) ?
((hwif->mmio) ? 0xF4 : 0x84) :
((hwif->mmio) ? 0xB4 : 0x80));
unsigned long ma = siimage_seldev(drive, 0x08);
unsigned long ua = siimage_seldev(drive, 0x0C);
if (hwif->mmio) {
scsc = hwif->INB(base + 0x4A);
mode = hwif->INB(base + addr_mask);
multi = hwif->INW(ma);
ultra = hwif->INW(ua);
} else {
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
pci_read_config_byte(hwif->pci_dev, addr_mask, &mode);
pci_read_config_word(hwif->pci_dev, ma, &multi);
pci_read_config_word(hwif->pci_dev, ua, &ultra);
}
mode &= ~((unit) ? 0x30 : 0x03);
ultra &= ~0x3F;
scsc = ((scsc & 0x30) == 0x00) ? 0 : 1;
scsc = is_sata(hwif) ? 1 : scsc;
switch(speed) {
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
multi = dma[speed - XFER_MW_DMA_0];
mode |= ((unit) ? 0x20 : 0x02);
break;
case XFER_UDMA_6:
case XFER_UDMA_5:
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
multi = dma[2];
ultra |= ((scsc) ? (ultra6[speed - XFER_UDMA_0]) :
(ultra5[speed - XFER_UDMA_0]));
mode |= ((unit) ? 0x30 : 0x03);
break;
default:
return;
}
if (hwif->mmio) {
hwif->OUTB(mode, base + addr_mask);
hwif->OUTW(multi, ma);
hwif->OUTW(ultra, ua);
} else {
pci_write_config_byte(hwif->pci_dev, addr_mask, mode);
pci_write_config_word(hwif->pci_dev, ma, multi);
pci_write_config_word(hwif->pci_dev, ua, ultra);
}
}
/* returns 1 if dma irq issued, 0 otherwise */
static int siimage_io_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_altstat = 0;
unsigned long addr = siimage_selreg(hwif, 1);
/* return 1 if INTR asserted */
if ((hwif->INB(hwif->dma_status) & 4) == 4)
return 1;
/* return 1 if Device INTR asserted */
pci_read_config_byte(hwif->pci_dev, addr, &dma_altstat);
if (dma_altstat & 8)
return 0; //return 1;
return 0;
}
/**
* siimage_mmio_ide_dma_test_irq - check we caused an IRQ
* @drive: drive we are testing
*
* Check if we caused an IDE DMA interrupt. We may also have caused
* SATA status interrupts, if so we clean them up and continue.
*/
static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long addr = siimage_selreg(hwif, 0x1);
if (SATA_ERROR_REG) {
unsigned long base = (unsigned long)hwif->hwif_data;
u32 ext_stat = readl((void __iomem *)(base + 0x10));
u8 watchdog = 0;
if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
u32 sata_error = readl((void __iomem *)SATA_ERROR_REG);
writel(sata_error, (void __iomem *)SATA_ERROR_REG);
watchdog = (sata_error & 0x00680000) ? 1 : 0;
printk(KERN_WARNING "%s: sata_error = 0x%08x, "
"watchdog = %d, %s\n",
drive->name, sata_error, watchdog,
__FUNCTION__);
} else {
watchdog = (ext_stat & 0x8000) ? 1 : 0;
}
ext_stat >>= 16;
if (!(ext_stat & 0x0404) && !watchdog)
return 0;
}
/* return 1 if INTR asserted */
if ((readb((void __iomem *)hwif->dma_status) & 0x04) == 0x04)
return 1;
/* return 1 if Device INTR asserted */
if ((readb((void __iomem *)addr) & 8) == 8)
return 0; //return 1;
return 0;
}
/**
* sil_sata_busproc - bus isolation IOCTL
* @drive: drive to isolate/restore
* @state: bus state to set
*
* Used by the SII3112 to handle bus isolation. As this is a
* SATA controller the work required is quite limited, we
* just have to clean up the statistics
*/
static int sil_sata_busproc(ide_drive_t * drive, int state)
{
ide_hwif_t *hwif = HWIF(drive);
u32 stat_config = 0;
unsigned long addr = siimage_selreg(hwif, 0);
if (hwif->mmio)
stat_config = readl((void __iomem *)addr);
else
pci_read_config_dword(hwif->pci_dev, addr, &stat_config);
switch (state) {
case BUSSTATE_ON:
hwif->drives[0].failures = 0;
hwif->drives[1].failures = 0;
break;
case BUSSTATE_OFF:
hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
break;
case BUSSTATE_TRISTATE:
hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
break;
default:
return -EINVAL;
}
hwif->bus_state = state;
return 0;
}
/**
* sil_sata_reset_poll - wait for SATA reset
* @drive: drive we are resetting
*
* Poll the SATA phy and see whether it has come back from the dead
* yet.
*/
static int sil_sata_reset_poll(ide_drive_t *drive)
{
if (SATA_STATUS_REG) {
ide_hwif_t *hwif = HWIF(drive);
/* SATA_STATUS_REG is valid only when in MMIO mode */
if ((readl((void __iomem *)SATA_STATUS_REG) & 0x03) != 0x03) {
printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
hwif->name, readl((void __iomem *)SATA_STATUS_REG));
HWGROUP(drive)->polling = 0;
return ide_started;
}
}
return 0;
}
/**
* sil_sata_pre_reset - reset hook
* @drive: IDE device being reset
*
* For the SATA devices we need to handle recalibration/geometry
* differently
*/
static void sil_sata_pre_reset(ide_drive_t *drive)
{
if (drive->media == ide_disk) {
drive->special.b.set_geometry = 0;
drive->special.b.recalibrate = 0;
}
}
/**
* proc_reports_siimage - add siimage controller to proc
* @dev: PCI device
* @clocking: SCSC value
* @name: controller name
*
* Report the clocking mode of the controller and add it to
* the /proc interface layer
*/
static void proc_reports_siimage (struct pci_dev *dev, u8 clocking, const char *name)
{
if (!pdev_is_sata(dev)) {
printk(KERN_INFO "%s: BASE CLOCK ", name);
clocking &= 0x03;
switch (clocking) {
case 0x03: printk("DISABLED!\n"); break;
case 0x02: printk("== 2X PCI\n"); break;
case 0x01: printk("== 133\n"); break;
case 0x00: printk("== 100\n"); break;
}
}
}
/**
* setup_mmio_siimage - switch an SI controller into MMIO
* @dev: PCI device we are configuring
* @name: device name
*
* Attempt to put the device into mmio mode. There are some slight
* complications here with certain systems where the mmio bar isnt
* mapped so we have to be sure we can fall back to I/O.
*/
static unsigned int setup_mmio_siimage (struct pci_dev *dev, const char *name)
{
unsigned long bar5 = pci_resource_start(dev, 5);
unsigned long barsize = pci_resource_len(dev, 5);
u8 tmpbyte = 0;
void __iomem *ioaddr;
u32 tmp, irq_mask;
/*
* Drop back to PIO if we can't map the mmio. Some
* systems seem to get terminally confused in the PCI
* spaces.
*/
if(!request_mem_region(bar5, barsize, name))
{
printk(KERN_WARNING "siimage: IDE controller MMIO ports not available.\n");
return 0;
}
ioaddr = ioremap(bar5, barsize);
if (ioaddr == NULL)
{
release_mem_region(bar5, barsize);
return 0;
}
pci_set_master(dev);
pci_set_drvdata(dev, (void *) ioaddr);
if (pdev_is_sata(dev)) {
/* make sure IDE0/1 interrupts are not masked */
irq_mask = (1 << 22) | (1 << 23);
tmp = readl(ioaddr + 0x48);
if (tmp & irq_mask) {
tmp &= ~irq_mask;
writel(tmp, ioaddr + 0x48);
readl(ioaddr + 0x48); /* flush */
}
writel(0, ioaddr + 0x148);
writel(0, ioaddr + 0x1C8);
}
writeb(0, ioaddr + 0xB4);
writeb(0, ioaddr + 0xF4);
tmpbyte = readb(ioaddr + 0x4A);
switch(tmpbyte & 0x30) {
case 0x00:
/* In 100 MHz clocking, try and switch to 133 */
writeb(tmpbyte|0x10, ioaddr + 0x4A);
break;
case 0x10:
/* On 133Mhz clocking */
break;
case 0x20:
/* On PCIx2 clocking */
break;
case 0x30:
/* Clocking is disabled */
/* 133 clock attempt to force it on */
writeb(tmpbyte & ~0x20, ioaddr + 0x4A);
break;
}
writeb( 0x72, ioaddr + 0xA1);
writew( 0x328A, ioaddr + 0xA2);
writel(0x62DD62DD, ioaddr + 0xA4);
writel(0x43924392, ioaddr + 0xA8);
writel(0x40094009, ioaddr + 0xAC);
writeb( 0x72, ioaddr + 0xE1);
writew( 0x328A, ioaddr + 0xE2);
writel(0x62DD62DD, ioaddr + 0xE4);
writel(0x43924392, ioaddr + 0xE8);
writel(0x40094009, ioaddr + 0xEC);
if (pdev_is_sata(dev)) {
writel(0xFFFF0000, ioaddr + 0x108);
writel(0xFFFF0000, ioaddr + 0x188);
writel(0x00680000, ioaddr + 0x148);
writel(0x00680000, ioaddr + 0x1C8);
}
tmpbyte = readb(ioaddr + 0x4A);
proc_reports_siimage(dev, (tmpbyte>>4), name);
return 1;
}
/**
* init_chipset_siimage - set up an SI device
* @dev: PCI device
* @name: device name
*
* Perform the initial PCI set up for this device. Attempt to switch
* to 133MHz clocking if the system isn't already set up to do it.
*/
static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev, const char *name)
{
u8 rev = dev->revision, tmpbyte = 0, BA5_EN = 0;
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255);
pci_read_config_byte(dev, 0x8A, &BA5_EN);
if ((BA5_EN & 0x01) || (pci_resource_start(dev, 5))) {
if (setup_mmio_siimage(dev, name)) {
return 0;
}
}
pci_write_config_byte(dev, 0x80, 0x00);
pci_write_config_byte(dev, 0x84, 0x00);
pci_read_config_byte(dev, 0x8A, &tmpbyte);
switch(tmpbyte & 0x30) {
case 0x00:
/* 133 clock attempt to force it on */
pci_write_config_byte(dev, 0x8A, tmpbyte|0x10);
case 0x30:
/* if clocking is disabled */
/* 133 clock attempt to force it on */
pci_write_config_byte(dev, 0x8A, tmpbyte & ~0x20);
case 0x10:
/* 133 already */
break;
case 0x20:
/* BIOS set PCI x2 clocking */
break;
}
pci_read_config_byte(dev, 0x8A, &tmpbyte);
pci_write_config_byte(dev, 0xA1, 0x72);
pci_write_config_word(dev, 0xA2, 0x328A);
pci_write_config_dword(dev, 0xA4, 0x62DD62DD);
pci_write_config_dword(dev, 0xA8, 0x43924392);
pci_write_config_dword(dev, 0xAC, 0x40094009);
pci_write_config_byte(dev, 0xB1, 0x72);
pci_write_config_word(dev, 0xB2, 0x328A);
pci_write_config_dword(dev, 0xB4, 0x62DD62DD);
pci_write_config_dword(dev, 0xB8, 0x43924392);
pci_write_config_dword(dev, 0xBC, 0x40094009);
proc_reports_siimage(dev, (tmpbyte>>4), name);
return 0;
}
/**
* init_mmio_iops_siimage - set up the iops for MMIO
* @hwif: interface to set up
*
* The basic setup here is fairly simple, we can use standard MMIO
* operations. However we do have to set the taskfile register offsets
* by hand as there isnt a standard defined layout for them this
* time.
*
* The hardware supports buffered taskfiles and also some rather nice
* extended PRD tables. For better SI3112 support use the libata driver
*/
static void __devinit init_mmio_iops_siimage(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
void *addr = pci_get_drvdata(dev);
u8 ch = hwif->channel;
hw_regs_t hw;
unsigned long base;
/*
* Fill in the basic HWIF bits
*/
default_hwif_mmiops(hwif);
hwif->hwif_data = addr;
/*
* Now set up the hw. We have to do this ourselves as
* the MMIO layout isnt the same as the standard port
* based I/O
*/
memset(&hw, 0, sizeof(hw_regs_t));
base = (unsigned long)addr;
if (ch)
base += 0xC0;
else
base += 0x80;
/*
* The buffered task file doesn't have status/control
* so we can't currently use it sanely since we want to
* use LBA48 mode.
*/
hw.io_ports[IDE_DATA_OFFSET] = base;
hw.io_ports[IDE_ERROR_OFFSET] = base + 1;
hw.io_ports[IDE_NSECTOR_OFFSET] = base + 2;
hw.io_ports[IDE_SECTOR_OFFSET] = base + 3;
hw.io_ports[IDE_LCYL_OFFSET] = base + 4;
hw.io_ports[IDE_HCYL_OFFSET] = base + 5;
hw.io_ports[IDE_SELECT_OFFSET] = base + 6;
hw.io_ports[IDE_STATUS_OFFSET] = base + 7;
hw.io_ports[IDE_CONTROL_OFFSET] = base + 10;
hw.io_ports[IDE_IRQ_OFFSET] = 0;
if (pdev_is_sata(dev)) {
base = (unsigned long)addr;
if (ch)
base += 0x80;
hwif->sata_scr[SATA_STATUS_OFFSET] = base + 0x104;
hwif->sata_scr[SATA_ERROR_OFFSET] = base + 0x108;
hwif->sata_scr[SATA_CONTROL_OFFSET] = base + 0x100;
hwif->sata_misc[SATA_MISC_OFFSET] = base + 0x140;
hwif->sata_misc[SATA_PHY_OFFSET] = base + 0x144;
hwif->sata_misc[SATA_IEN_OFFSET] = base + 0x148;
}
memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
hwif->irq = dev->irq;
hwif->dma_base = (unsigned long)addr + (ch ? 0x08 : 0x00);
hwif->mmio = 1;
}
static int is_dev_seagate_sata(ide_drive_t *drive)
{
const char *s = &drive->id->model[0];
unsigned len;
if (!drive->present)
return 0;
len = strnlen(s, sizeof(drive->id->model));
if ((len > 4) && (!memcmp(s, "ST", 2))) {
if ((!memcmp(s + len - 2, "AS", 2)) ||
(!memcmp(s + len - 3, "ASL", 3))) {
printk(KERN_INFO "%s: applying pessimistic Seagate "
"errata fix\n", drive->name);
return 1;
}
}
return 0;
}
/**
* siimage_fixup - post probe fixups
* @hwif: interface to fix up
*
* Called after drive probe we use this to decide whether the
* Seagate fixup must be applied. This used to be in init_iops but
* that can occur before we know what drives are present.
*/
static void __devinit siimage_fixup(ide_hwif_t *hwif)
{
/* Try and raise the rqsize */
if (!is_sata(hwif) || !is_dev_seagate_sata(&hwif->drives[0]))
hwif->rqsize = 128;
}
/**
* init_iops_siimage - set up iops
* @hwif: interface to set up
*
* Do the basic setup for the SIIMAGE hardware interface
* and then do the MMIO setup if we can. This is the first
* look in we get for setting up the hwif so that we
* can get the iops right before using them.
*/
static void __devinit init_iops_siimage(ide_hwif_t *hwif)
{
hwif->hwif_data = NULL;
/* Pessimal until we finish probing */
hwif->rqsize = 15;
if (pci_get_drvdata(hwif->pci_dev) == NULL)
return;
init_mmio_iops_siimage(hwif);
}
/**
* ata66_siimage - check for 80 pin cable
* @hwif: interface to check
*
* Check for the presence of an ATA66 capable cable on the
* interface.
*/
static u8 __devinit ata66_siimage(ide_hwif_t *hwif)
{
unsigned long addr = siimage_selreg(hwif, 0);
u8 ata66 = 0;
if (pci_get_drvdata(hwif->pci_dev) == NULL)
pci_read_config_byte(hwif->pci_dev, addr, &ata66);
else
ata66 = hwif->INB(addr);
return (ata66 & 0x01) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}
/**
* init_hwif_siimage - set up hwif structs
* @hwif: interface to set up
*
* We do the basic set up of the interface structure. The SIIMAGE
* requires several custom handlers so we override the default
* ide DMA handlers appropriately
*/
static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
{
u8 sata = is_sata(hwif);
hwif->set_pio_mode = &sil_set_pio_mode;
hwif->set_dma_mode = &sil_set_dma_mode;
if (sata) {
static int first = 1;
hwif->busproc = &sil_sata_busproc;
hwif->reset_poll = &sil_sata_reset_poll;
hwif->pre_reset = &sil_sata_pre_reset;
hwif->udma_filter = &sil_sata_udma_filter;
if (first) {
printk(KERN_INFO "siimage: For full SATA support you should use the libata sata_sil module.\n");
first = 0;
}
} else
hwif->udma_filter = &sil_pata_udma_filter;
if (hwif->dma_base == 0)
return;
if (sata)
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_siimage(hwif);
if (hwif->mmio) {
hwif->ide_dma_test_irq = &siimage_mmio_ide_dma_test_irq;
} else {
hwif->ide_dma_test_irq = & siimage_io_ide_dma_test_irq;
}
}
#define DECLARE_SII_DEV(name_str) \
{ \
.name = name_str, \
.init_chipset = init_chipset_siimage, \
.init_iops = init_iops_siimage, \
.init_hwif = init_hwif_siimage, \
.fixup = siimage_fixup, \
.host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
.mwdma_mask = ATA_MWDMA2, \
.udma_mask = ATA_UDMA6, \
}
static const struct ide_port_info siimage_chipsets[] __devinitdata = {
/* 0 */ DECLARE_SII_DEV("SiI680"),
/* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA"),
/* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA")
};
/**
* siimage_init_one - pci layer discovery entry
* @dev: PCI device
* @id: ident table entry
*
* Called by the PCI code when it finds an SI680 or SI3112 controller.
* We then use the IDE PCI generic helper to do most of the work.
*/
static int __devinit siimage_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
return ide_setup_pci_device(dev, &siimage_chipsets[id->driver_data]);
}
static const struct pci_device_id siimage_pci_tbl[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), 0 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112), 1 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
#endif
{ 0, },
};
MODULE_DEVICE_TABLE(pci, siimage_pci_tbl);
static struct pci_driver driver = {
.name = "SiI_IDE",
.id_table = siimage_pci_tbl,
.probe = siimage_init_one,
};
static int __init siimage_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
module_init(siimage_ide_init);
MODULE_AUTHOR("Andre Hedrick, Alan Cox");
MODULE_DESCRIPTION("PCI driver module for SiI IDE");
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink