b72f92ff55
Drivers which are going to use it will have to select it and use imx_set_irq_fiq() to set FIQ mode for this interrupt. Changes since V1: - removed '#ifdef CONFIG_FIQ' from irqs.h - renamed imx_set_irq_type() to imx_set_irq_fiq() - made irqt unsigned - fixed irq number check Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
122 lines
4.0 KiB
C
122 lines
4.0 KiB
C
/*
|
|
* arch/arm/mach-imxads/include/mach/irqs.h
|
|
*
|
|
* Copyright (C) 1999 ARM Limited
|
|
* Copyright (C) 2000 Deep Blue Solutions Ltd.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
|
|
#ifndef __ARM_IRQS_H__
|
|
#define __ARM_IRQS_H__
|
|
|
|
/* Use the imx definitions */
|
|
#include <mach/hardware.h>
|
|
|
|
/*
|
|
* IMX Interrupt numbers
|
|
*
|
|
*/
|
|
#define INT_SOFTINT 0
|
|
#define CSI_INT 6
|
|
#define DSPA_MAC_INT 7
|
|
#define DSPA_INT 8
|
|
#define COMP_INT 9
|
|
#define MSHC_XINT 10
|
|
#define GPIO_INT_PORTA 11
|
|
#define GPIO_INT_PORTB 12
|
|
#define GPIO_INT_PORTC 13
|
|
#define LCDC_INT 14
|
|
#define SIM_INT 15
|
|
#define SIM_DATA_INT 16
|
|
#define RTC_INT 17
|
|
#define RTC_SAMINT 18
|
|
#define UART2_MINT_PFERR 19
|
|
#define UART2_MINT_RTS 20
|
|
#define UART2_MINT_DTR 21
|
|
#define UART2_MINT_UARTC 22
|
|
#define UART2_MINT_TX 23
|
|
#define UART2_MINT_RX 24
|
|
#define UART1_MINT_PFERR 25
|
|
#define UART1_MINT_RTS 26
|
|
#define UART1_MINT_DTR 27
|
|
#define UART1_MINT_UARTC 28
|
|
#define UART1_MINT_TX 29
|
|
#define UART1_MINT_RX 30
|
|
#define VOICE_DAC_INT 31
|
|
#define VOICE_ADC_INT 32
|
|
#define PEN_DATA_INT 33
|
|
#define PWM_INT 34
|
|
#define SDHC_INT 35
|
|
#define I2C_INT 39
|
|
#define CSPI_INT 41
|
|
#define SSI_TX_INT 42
|
|
#define SSI_TX_ERR_INT 43
|
|
#define SSI_RX_INT 44
|
|
#define SSI_RX_ERR_INT 45
|
|
#define TOUCH_INT 46
|
|
#define USBD_INT0 47
|
|
#define USBD_INT1 48
|
|
#define USBD_INT2 49
|
|
#define USBD_INT3 50
|
|
#define USBD_INT4 51
|
|
#define USBD_INT5 52
|
|
#define USBD_INT6 53
|
|
#define BTSYS_INT 55
|
|
#define BTTIM_INT 56
|
|
#define BTWUI_INT 57
|
|
#define TIM2_INT 58
|
|
#define TIM1_INT 59
|
|
#define DMA_ERR 60
|
|
#define DMA_INT 61
|
|
#define GPIO_INT_PORTD 62
|
|
|
|
#define IMX_IRQS (64)
|
|
|
|
/* note: the IMX has four gpio ports (A-D), but only
|
|
* the following pins are connected to the outside
|
|
* world:
|
|
*
|
|
* PORT A: bits 0-31
|
|
* PORT B: bits 8-31
|
|
* PORT C: bits 3-17
|
|
* PORT D: bits 6-31
|
|
*
|
|
* We map these interrupts straight on. As a result we have
|
|
* several holes in the interrupt mapping. We do this for two
|
|
* reasons:
|
|
* - mapping the interrupts without holes would get
|
|
* far more complicated
|
|
* - Motorola could well decide to bring some processor
|
|
* with more pins connected
|
|
*/
|
|
|
|
#define IRQ_GPIOA(x) (IMX_IRQS + x)
|
|
#define IRQ_GPIOB(x) (IRQ_GPIOA(32) + x)
|
|
#define IRQ_GPIOC(x) (IRQ_GPIOB(32) + x)
|
|
#define IRQ_GPIOD(x) (IRQ_GPIOC(32) + x)
|
|
|
|
/* decode irq number to use with IMR(x), ISR(x) and friends */
|
|
#define IRQ_TO_REG(irq) ((irq - IMX_IRQS) >> 5)
|
|
|
|
/* all normal IRQs can be FIQs */
|
|
#define FIQ_START 0
|
|
/* switch betwean IRQ and FIQ */
|
|
extern int imx_set_irq_fiq(unsigned int irq, unsigned int type);
|
|
|
|
#define NR_IRQS (IRQ_GPIOD(32) + 1)
|
|
#define IRQ_GPIO(x)
|
|
#endif
|