05f94eebd5
CFE is the only supported and used bootloader on the SiByte boards, the standalone kernel support has been never used outside Broadcom. Remove it and make the kernel use CFE by default. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
172 lines
3.5 KiB
Plaintext
172 lines
3.5 KiB
Plaintext
config SIBYTE_SB1250
|
|
bool
|
|
select CEVT_SB1250
|
|
select CSRC_SB1250
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select SIBYTE_ENABLE_LDT_IF_PCI
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SIBYTE_SB1xxx_SOC
|
|
select SYS_SUPPORTS_SMP
|
|
|
|
config SIBYTE_BCM1120
|
|
bool
|
|
select CEVT_SB1250
|
|
select CSRC_SB1250
|
|
select IRQ_CPU
|
|
select SIBYTE_BCM112X
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SIBYTE_SB1xxx_SOC
|
|
|
|
config SIBYTE_BCM1125
|
|
bool
|
|
select CEVT_SB1250
|
|
select CSRC_SB1250
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select SIBYTE_BCM112X
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SIBYTE_SB1xxx_SOC
|
|
|
|
config SIBYTE_BCM1125H
|
|
bool
|
|
select CEVT_SB1250
|
|
select CSRC_SB1250
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select SIBYTE_BCM112X
|
|
select SIBYTE_ENABLE_LDT_IF_PCI
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SIBYTE_SB1xxx_SOC
|
|
|
|
config SIBYTE_BCM112X
|
|
bool
|
|
select CEVT_SB1250
|
|
select CSRC_SB1250
|
|
select IRQ_CPU
|
|
select SIBYTE_SB1xxx_SOC
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
|
|
config SIBYTE_BCM1x80
|
|
bool
|
|
select CEVT_BCM1480
|
|
select CSRC_BCM1480
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SIBYTE_SB1xxx_SOC
|
|
select SYS_SUPPORTS_SMP
|
|
|
|
config SIBYTE_BCM1x55
|
|
bool
|
|
select CEVT_BCM1480
|
|
select CSRC_BCM1480
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select SIBYTE_SB1xxx_SOC
|
|
select SIBYTE_HAS_ZBUS_PROFILING
|
|
select SYS_SUPPORTS_SMP
|
|
|
|
config SIBYTE_SB1xxx_SOC
|
|
bool
|
|
select DMA_COHERENT
|
|
select IRQ_CPU
|
|
select SIBYTE_CFE
|
|
select SWAP_IO_SPACE
|
|
select SYS_SUPPORTS_32BIT_KERNEL
|
|
select SYS_SUPPORTS_64BIT_KERNEL
|
|
select CFE
|
|
select SYS_HAS_EARLY_PRINTK
|
|
|
|
choice
|
|
prompt "SiByte SOC Stepping"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
|
|
config CPU_SB1_PASS_1
|
|
bool "1250 Pass1"
|
|
depends on SIBYTE_SB1250
|
|
select CPU_HAS_PREFETCH
|
|
|
|
config CPU_SB1_PASS_2_1250
|
|
bool "1250 An"
|
|
depends on SIBYTE_SB1250
|
|
select CPU_SB1_PASS_2
|
|
help
|
|
Also called BCM1250 Pass 2
|
|
|
|
config CPU_SB1_PASS_2_2
|
|
bool "1250 Bn"
|
|
depends on SIBYTE_SB1250
|
|
select CPU_HAS_PREFETCH
|
|
help
|
|
Also called BCM1250 Pass 2.2
|
|
|
|
config CPU_SB1_PASS_4
|
|
bool "1250 Cn"
|
|
depends on SIBYTE_SB1250
|
|
select CPU_HAS_PREFETCH
|
|
help
|
|
Also called BCM1250 Pass 3
|
|
|
|
config CPU_SB1_PASS_2_112x
|
|
bool "112x Hybrid"
|
|
depends on SIBYTE_BCM112X
|
|
select CPU_SB1_PASS_2
|
|
|
|
config CPU_SB1_PASS_3
|
|
bool "112x An"
|
|
depends on SIBYTE_BCM112X
|
|
select CPU_HAS_PREFETCH
|
|
|
|
endchoice
|
|
|
|
config CPU_SB1_PASS_2
|
|
bool
|
|
|
|
config SIBYTE_HAS_LDT
|
|
bool
|
|
|
|
config SIBYTE_ENABLE_LDT_IF_PCI
|
|
bool
|
|
select SIBYTE_HAS_LDT if PCI
|
|
|
|
config SB1_CEX_ALWAYS_FATAL
|
|
bool "All cache exceptions considered fatal (no recovery attempted)"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
|
|
config SB1_CERR_STALL
|
|
bool "Stall (rather than panic) on fatal cache error"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
|
|
config SIBYTE_CFE_CONSOLE
|
|
bool "Use firmware console"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
help
|
|
Use the CFE API's console write routines during boot. Other console
|
|
options (VT console, sb1250 duart console, etc.) should not be
|
|
configured.
|
|
|
|
config SIBYTE_BUS_WATCHER
|
|
bool "Support for Bus Watcher statistics"
|
|
depends on SIBYTE_SB1xxx_SOC
|
|
help
|
|
Handle and keep statistics on the bus error interrupts (COR_ECC,
|
|
BAD_ECC, IO_BUS).
|
|
|
|
config SIBYTE_BW_TRACE
|
|
bool "Capture bus trace before bus error"
|
|
depends on SIBYTE_BUS_WATCHER
|
|
help
|
|
Run a continuous bus trace, dumping the raw data as soon as
|
|
a ZBbus error is detected. Cannot work if ZBbus profiling
|
|
is turned on, and also will interfere with JTAG-based trace
|
|
buffer activity. Raw buffer data is dumped to console, and
|
|
must be processed off-line.
|
|
|
|
config SIBYTE_TBPROF
|
|
tristate "Support for ZBbus profiling"
|
|
depends on SIBYTE_HAS_ZBUS_PROFILING
|
|
|
|
config SIBYTE_HAS_ZBUS_PROFILING
|
|
bool
|