diff --git a/doc/user_guide/en/decoder_notes.adoc b/doc/user_guide/en/decoder_notes.adoc
index 33f4df6ed..b4fb8e8e4 100644
--- a/doc/user_guide/en/decoder_notes.adoc
+++ b/doc/user_guide/en/decoder_notes.adoc
@@ -1,9 +1,10 @@
 === AP Decoding
 
-The _WSJT-X_ decoders for QRA64 and FT8 include optional procedures
-that use naturally accumulating information during a minimal QSO.
-This _a priori_ (AP) information increases sensitivity of the decoder
-by up to 4 dB, at the cost of a slightly higher rate of false decodes.
+The _WSJT-X_ decoders for JT65, QRA64, and FT8 include optional
+procedures that use naturally accumulating information during a
+minimal QSO.  This _a priori_ (AP) information increases sensitivity
+of the decoder by up to 4 dB, at the cost of a slightly higher rate of
+false decodes.
 
 For example: when you decide to answer a CQ, you already know your own
 callsign and that of your potential QSO partner.  The software
diff --git a/doc/user_guide/en/new_features.adoc b/doc/user_guide/en/new_features.adoc
index f0e032517..c947ad827 100644
--- a/doc/user_guide/en/new_features.adoc
+++ b/doc/user_guide/en/new_features.adoc
@@ -9,6 +9,8 @@ situations
 - Decoding improvements for JT65 mode, including _a priori_ (AP)
 decoding when VHF/UHF/Microwave features are enabled
 
+- Optional Auto-Sequencing in JT4, JT9, and JT65 when VHF/UHF/Microwave features are enabled
+
 - Better suppression of low-confidence false decodes generated by AP
 decoding in FT8 mode
 
diff --git a/doc/user_guide/en/vhf-features.adoc b/doc/user_guide/en/vhf-features.adoc
index 3e3faa067..d0a4cd731 100644
--- a/doc/user_guide/en/vhf-features.adoc
+++ b/doc/user_guide/en/vhf-features.adoc
@@ -8,6 +8,8 @@ signals
 
 - *JT9* fast modes, useful for scatter propagation on VHF bands
 
+- *JT65*, widely used for EME on VHF and higher bands
+
 - *QRA64*, a mode for EME using a "`Q-ary Repeat Accumulate`" code,
 a low-density parity-check (LDPC) code using a 64-character symbol
 alphabet
@@ -24,6 +26,8 @@ propagation
 - *Doppler tracking*, which becomes increasingly important for EME
 on bands above 1.2 GHz.
 
+- Optional *Auto-Sequencing* in JT4, JT9, and JT65 as well as FT8 and QRA64.
+
 [[VHF_SETUP]]
 === VHF Setup
 
@@ -164,8 +168,9 @@ shorthand messages for RO, RRR, and 73.  These messages are always
 enabled for reception; they will be automatically generated for
 transmission if you check the shorthand message box *Sh*.
 
-Be sure to check *Deep* on the *Decode* menu; you may optionally
-include *Enable averaging* and *Deep search*.
+*Deep* on the *Decode* menu will be automatically selected.  You may
+optionally include *Enable averaging*, *Enable Deep search*, and
+*Enable AP*.
 
 The following screen shot shows three transmissions from a 144 MHz EME
 QSO using submode JT65B and shorthand messages.  Take note of the