1. Updated two screen pix in User's Guide.

2. Revise, revise, revise.  Good writing requires plenty of revisions!


git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3667 ab8295b8-cf94-4d9e-aec4-7959e3be5d79

doc/source/configuration-band-settings.adoc

@@ -4,3 +4,5 @@ The Band Settings tab allows you to define the default frequency and
 enter a brief description of your antenna for each amateur band.  The
 antenna information will be included with reception reports to
 {pskreporter}, if enabled.
+
+(Figure to be added here.)

doc/source/configuration-station.adoc

@@ -19,24 +19,6 @@ frequency. To enable this capability:
 - Check the box *Enable CAT*
 - Select your radio type from a drop-down list
 - Select a *CAT port* (not the same port selected for PTT control)
-- Set the correct port parameters (*Serial rate*, *Handshake*, *Data bits*, 
-*Stop bits*) for your radio
-- If you use {dxlcommander} or {hrd} to control your transceiver, you
-can configure _WSJT-X_ to communicate with the radio through that
-program.  Entries for these programs appear at the end of the
-drop-down list of supported rigs.
-
-[[X11]]
-image::images/r3563-config-screen-80.png[align="center",alt="Configuration Screen"]
-
-For now you should leave *Split Tx* unchecked. If you are using CAT
-control, most radios will allow you to set *PTT method* = CAT.  Some
-radios support two types of PTT assertion via CAT control: one takes
-audio input from the Mic connector, the other from a rear-panel Data
-connector.  The simplest CAT configuration sets *Polling interval* = 0
-(no polling the radio for dial frequency).  _WSJT-X_ will then be able
-to set the radio’s frequency, but the program will be unaware of
-subsequent changes made using the radio’s panel controls.
 
 TIP: If you need an additional item in the list of devices for the
 CAT port, edit the configuration file +wsjtx.ini+ and add your
@@ -44,6 +26,25 @@ requirement as +CATdriver=<yourdriver>+ (for example,
 +CATdriver=/dev/tty.usbserial+) in the group of entries marked
 +[Common]+.
 
+- Set the port parameters *Serial rate*, *Handshake*, *Data bits*, 
+*Stop bits* as required for your radio
+- If you use {dxlcommander} or {hrd} to control your transceiver, you
+can configure _WSJT-X_ to communicate with the radio through that
+program.  Entries for these programs appear at the end of the
+drop-down list of supported rigs.
+
+[[X11]]
+image::images/r3666-config-screen-80.png[align="center",alt="Configuration Screen"]
+
+Leave *Split Tx* unchecked for now. If you are using CAT control, most
+radios will allow you to set *PTT method* = CAT.  Some radios support
+two types of PTT assertion via CAT control: one takes audio input from
+the Mic connector, the other from a rear-panel Data connector.  The
+simplest CAT configuration sets *Polling interval* = 0 (no polling the
+radio for dial frequency).  _WSJT-X_ can then set the radio’s
+frequency, but the program will be unaware of subsequent changes made
+using the radio’s panel controls.
+
 With most radios you can set *Polling interval* to a small number (say
 1 – 3 s) and the program will follow any frequency changes made at the
 radio.  Note that you may not be able simultaneously to control the
@@ -55,6 +56,6 @@ and to exit the program before turning the equipment off.
 
 - Click the *Test CAT Control* and *Test PTT* buttons to see that you
 have established the desired control of station functions.  
-- Select the devices you will use for Audio input and output.
+- Select the devices you will use for *Audio In* and *Audio Out*.
 - Click *OK* to dismiss the *Configuration* window.
 

doc/source/configuration-txmacros.adoc

@@ -3,4 +3,6 @@
 *Tx Macros* are an aid for sending commonly used free-text messages.
 To enable a pull-down selection, add your custom messages to the entry
 fields provided.  In JT65 and JT9 the maximum free-text message length
-is 13 characters, including spaces.
+is 13 characters, including embedded spaces.
+
+(Figure to be added here.)

doc/source/font-sizes.adoc

@@ -11,5 +11,5 @@ Frequency* windows.
 
 - By default the four numbers are ``8 50 10 50''. If you need larger
 fonts in the user interface and bold text in the decode windows, try
-``10 50 12 100'' (without the quotes).
+something like ``10 50 12 100'' (without the quotes).
 

doc/source/install-from-source.adoc

@@ -3,10 +3,8 @@
 // to a very old src version of WSJT 5.7 or so. WSJTX is not listed at all.
 // Also, all the Qt4 stuff is now obsolete, and needs to be updated.
 
-_WSJT-X_ is an open-source program released under the GNU General
+Source code is available from the public repository at {devsvn}. To
-Public License (GPL).  Source code is available from the public repository
+compile the program you will need to install the following packages:
-at {devsvn}. To compile the program you will need to install the 
-following packages:
 
 - Subversion
 - Qt 5.x
@@ -19,6 +17,6 @@ following packages:
 With Subversion installed, the full source code for _WSJT-X_ can be
 downloaded with the command:
 
- $ svn co svn://svn.berlios.de/wsjt/branches/wsjtx 
+  svn co svn://svn.berlios.de/wsjt/branches/wsjtx 
 
 // Need further compiling Instructions

doc/source/install-mac.adoc

@@ -1,16 +1,17 @@
 // Status=review
 
 Two different packages are available: one for OS X 10.6 through 10.8,
-and one for OS X 10.9. The two versions are _not_ interchangeable.
+and one for OS X 10.9. The two packages are _not_ interchangeable.
 
 - Select the correct package for your OS X and download it to your desktop.
+** {osx-108}
+** {osx-109}
 
 - Double-click on the file to see a new folder, +WSJT-X+.  Drop down
 into that folder, where a +Readme+ file provides detailed instructions
 on how to configure your system for _WSJT-X_.
 
-- Some additional information can be found {osx-instructions}.
+- Additional information from package developer G4KLA 
-* {osx-108}
+can be found {osx-instructions}.
-* {osx-109}
 
 // Any necessary instructions about time synchronization or sound setup ??

doc/source/install-ubuntu.adoc

@@ -1,6 +1,7 @@
 // Status=review
+
 - Installation packages for Ubuntu 12.04, 12.10, 13.04, 13.10 are
-available at {launchpadurl}.
+maintained by AC6SL and available at {launchpadurl}.
 
 - If you have not before obtained packages from the Personal Package
 Archive (PPA) at the above link, open a terminal window and execute

doc/source/install-windows.adoc

@@ -16,10 +16,10 @@ downloading and installation instructions.
 
 - _WSJT-X_ expects your sound card to do its raw sampling at 48000 Hz.
 To ensure that this will be so when running under recent versions of
-Windows, open the system's sound control panel and select in turn the
+Windows, open the system's *Sound* control panel and select in turn the
-*Recording* and *Playback* options.  Click on *Properties*, then
+*Recording* and *Playback* tabs.  Click on *Properties*, then
 *Advanced*, and select ``16 bit, 48000 Hz (DVD Quality).''
 
-CAUTION: If you are using a sound card that is also the default device
+CAUTION: If you are using a sound card that is also the Windows
-for Windows sounds, be sure to turn off all such sounds so they are
+default audio device, be sure to turn off all Windows sounds so they
-not transmitted over the air.
+are not transmitted over the air.

doc/source/introduction.adoc

@@ -1,9 +1,10 @@
 // Status=review
+
 _WSJT-X_ is a computer program designed to facilitate basic amateur
 radio communication using very weak signals.  The first four letters
-in the program name stand for “Weak Signal communication by K1JT”, and
+in the program name stand for ``Weak Signal communication by K1JT'',
-the “-X” suffix indicates that _WSJT-X_ started as an extended (and
+and the “-X” suffix indicates that _WSJT-X_ started as an extended
-experimental) branch of program _WSJT_.
+(and experimental) branch of program _WSJT_.
 
 _WSJT-X_ currently offers two protocols or “modes,” JT65 and JT9.
 Both are designed for making reliable, confirmed QSOs under extreme
@@ -15,8 +16,9 @@ It is about 2 dB more sensitive than JT65 while using less than 10% of
 the bandwidth.  Both modes use one-minute timed sequences of
 alternating transmission and reception, so a minimal QSO takes four to
 six minutes — two or three transmissions by each station, one sending
-in odd UTC minutes and the other even.  World-wide QSOs are possible
+in odd UTC minutes and the other even.  On the HF bands, world-wide
-with power levels of a few watts and compromise antennas.
+QSOs are possible with power levels of a few watts and compromise
+antennas.
 
 _WSJT-X_ can display a bandpass as large as 5 kHz and transparently
 provides dual-mode reception of both JT65 and JT9 signals.  If your
@@ -29,10 +31,11 @@ make QSOs in both modes using nothing more than mouse clicks.
 Plans for future program development call for _WSJT-X_ and _WSJT_ to
 merge together. _WSJT-X_ will gradually acquire the additional modes
 JT4, FSK441, and ISCAT that are now supported in _WSJT_.  The entire
-WSJT-related effort is an open-source project.  If you have
+WSJT-related effort is an open-source project, released under the GNU
-programming or documentation skills or would like to contribute to the
+General Public License (GPL).  If you have programming or
-project in other ways, please make your interests known to the
+documentation skills or would like to contribute to the project in
-development team.  The project’s source-code repository can be found
+other ways, please make your interests known to the development team.
-at {devsvn}, and communication among the developers takes place on the
+The project’s source-code repository can be found at {devsvn}, and
-email reflector {devmail}.
+most communication among the developers takes place on the email
+reflector {devmail}.
 

doc/source/tutorial-example1.adoc

@@ -14,21 +14,21 @@ image::images/r3556-main-ui-80.png[align="center",alt="Main UI and Wide Graph"]
 Notice the [green]*GREEN* and [red]*RED* markers on the waterfall
 frequency scale.  Decoding takes place at the end of a receive
 sequence and is organized in two stages.  The first decodes take place
-at the selected Rx frequency, indicated by the [green]*GREEN* marker.
+at the selected Rx frequency, indicated by the [green]*GREEN* marker
-Results appear in both the left (*Band Activity*) and right (*Rx
+on the waterfall scale.  Results appear in both the left (*Band
-Frequency*) text windows on the main screen. The program then finds
+Activity*) and right (*Rx Frequency*) text windows on the main
-and decodes all signals in the selected mode or modes over the
+screen. The program then finds and decodes all signals in the selected
-displayed frequency range. The [red]*RED* marker indicates your Tx
+mode(s) over the displayed frequency range. The [red]*RED* marker
-frequency.
+indicates your Tx frequency.
 
 At least eight JT9 signals are present in the example file; all but
 one of them are decodable.  When this file was recorded KF4RWA was
 finishing a QSO with K1JT.  Since the green marker was placed at his
-audio frequency, 1224 Hz, his message “K1JT KF4RWA 73” appears in the
+audio frequency, 1224 Hz, his message ``K1JT KF4RWA 73'' is decoded
-*Rx Frequency* window. The *Band Activity* window shows this message
+first and appears in the *Rx Frequency* window. The *Band Activity*
-plus all the other decodes at nearby frequencies.  The CQ lines are
+window shows this message plus all decodes at other frequencies.  The
-highlighted in [green]*GREEN*, and lines containing *My Call*, in this
+Lines containing CQ are highlighted in [green]*GREEN*, and lines
-case K1JT, are highlighted in [red]*RED*.
+with *My Call* (in this case K1JT) in [red]*RED*.
 
 TIP: For this step and the next, you may want to pretend you are K1JT
 by entering that callsign temporarily as *My Call* on the <<X11,*Setup
@@ -38,8 +38,8 @@ those shown in the screen shot above.
 [[X13]]
 .Decoding Controls
 
-To gain some feeling for the controls frequently used when making
+To gain some feeling for controls frequently used when making QSOs,
-QSOs, try clicking with the mouse on the decoded text lines and on the
+try clicking with the mouse on the decoded text lines and on the
 waterfall spectral display. You should be able to confirm the
 following behavior:
 
@@ -49,7 +49,7 @@ green. This action produces the following results:
 ** Callsign and locator of a station calling CQ are copied to the *DX
 Call* and *DX Grid* entry fields.
 
-** Messages are generated for a minimal QSO.
+** Messages are generated for a standard minimal QSO.
 
 ** The *Tx even* box is checked or cleared appropriately, so that you
 will transmit in the proper (odd or even) minutes.
@@ -60,9 +60,9 @@ CQing station.
 ** The *Gen Msg* (``generated message'') radio button at bottom right 
 of the main window is selected.
 
-** If you have checked *Double-click on call sets Tx Enable* on the
+** If you had checked *Double-click on call sets Tx Enable* on the
-*Setup* menu, *Enable Tx* is activated and a transmission starts
+*Setup* menu, *Enable Tx* would be activated and a transmission would
-automatically at the appropriate time.
+start automatically at the proper time.
 
 - Double-click on the decoded message ``K1JT N5KDV EM41'',
 highlighted in [red]*RED*.  Results will be similar to those in the
@@ -71,9 +71,9 @@ moved.  Such messages are usually in response to your own CQ, or from
 a tail-ender, and you probably want your Tx frequency to stay where it
 was.
 
-- By holding down the *Ctrl* key when double-clicking on the decoded line 
+- By holding down the *Ctrl* key when double-clicking on a decoded
-you can cause both Tx and Rx frequencies to be moved.  This behavior
+line you can cause both Tx and Rx frequencies to be moved.  This
-can also be forced by checking *Lock Tx=Rx*. 
+behavior can also be forced by checking *Lock Tx=Rx*.
 
 - Double-click on the message from KF4RWA in either window. He is
 sending ``73'' to K1JT, signifying that the QSO is over.  Most likely
@@ -87,10 +87,10 @@ call CQ again.)
 - Ctrl-click on waterfall to set both Rx and Tx frequencies.
 
 - Double-click on the waterfall to set Rx frequency and start a
-narrow-band decode there. Decoded text appears in the right window
+narrow-band decode there. Decoded text will appear in the right window
-only.  
+only.
 
-- Ctrl-double-click to set both Rx and Tx frequencies and decodes at
+- Ctrl-double-click to set both Rx and Tx frequencies and decode at
 the new frequency.
 
 - Click *Erase* to clear the right window. 

doc/source/tutorial-example2.adoc

@@ -6,7 +6,7 @@
 frequency limit is approximately 4000 Hz.
 
 .Main Window:
-- Select *JT9+JT65* on the *Mode* menu
+- Select *JT9+JT65* on the *Mode* menu.
 - Toggle the *Tx mode* button to read *Tx JT65*, and set the Tx and Rx
 frequencies to 1718 Hz.
 - Double-click on *Erase* to clear both text windows.
@@ -38,11 +38,14 @@ been decoded first.
 
 - Confirm that mouse-click behavior is similar to that described
 <<X13,earlier>>, in Example 1. The program automatically determines
-the mode of each JT9 or JT65 signal.  Note that when you double-click
+the mode of each JT9 or JT65 signal.  
-on a signal in the waterfall, this is true even if the signal is on
+
-the ``wrong'' side of the [blue]*BLUE* *JT65 nnnn JT9* marker.  When
+TIP: When you double-click on a signal in the waterfall it will be
-clicking on a JT65 signal to decode it, click on the sync tone at the
+properly decoded even if on the ``wrong'' side of the *JT65 nnnn JT9*
-left edge.
+marker.  The Tx mode automatically switches to that of the decoded
+signal and the Rx and Tx frequency markers on the waterfall scale
+resize themselves accordingly. When selecting a JT65 signal, click on
+the sync tone at its left edge.
 
 - Double-click on the waterfall near 815 Hz: a JT65 message
 originating from W7VP will be decoded and appear in the *Rx Frequency*
@@ -54,8 +57,8 @@ window.
 |2343|-7|0.3|815|#|KK4DSD W7VP -16
 |=================================
 
-- Double-click on the waterfall at 3196 Hz and the program will decode a JT9
+- Double-click on the waterfall at 3196 Hz.  The program will decode a
-message from IZ0MIT:
+JT9 message from IZ0MIT:
 
 [width="70%",cols="3,^3,^3,^4,^4,30",options="header"]
 |=====================================
@@ -63,11 +66,6 @@ message from IZ0MIT:
 |2343|-7|0.3|3196|@|WB8QPG IZ0MIT -11
 |=====================================
 
-TIP: Notice that when a signal is decoded in this way, the Tx mode
-automatically switches to that of the decoded signal and the Rx and Tx
-frequency markers on the waterfall scale resize themselves
-accordingly.
-
 - Scroll back in the *Band Activity* window and double-click on the
 message CQ DL7ACA JO40.  The program will set *Tx mode* to JT65 and Tx
 and Rx frequencies to that of DL7ACA, 975 Hz.  If you had checked

doc/source/tutorial-main-window.adoc

@@ -1,5 +1,6 @@
 // Status=review
+
 - Click the *Stop* button on the main window to halt any data acquisition.  
 - Select *JT9* from the *Mode* menu and *Deepest* from the *Decode* menu.
-- Set the audio frequencies to *Tx 1224 Hz* and Rx 1224 Hz*.
+- Set the audio frequencies to *Tx 1224 Hz* and *Rx 1224 Hz*.
-//Maybe  show small screen shots here?
+

doc/source/tutorial-wide-graph-settings.adoc

@@ -1,9 +1,10 @@
 // Status=review
+
 - *Bins/Pixel* = 4
-- *JT65 2500 JT9*
+- *JT65 .... JT9* = 2500
 - *Start* = 0
 - *N Avg* = 5
-- *Zero* = –10
+- *Zero* = 0
 - *Gain* = 0,
 - *Palette* = Digipan
 - *Flatten* = checked

doc/source/wsjtx-main.adoc

@@ -30,8 +30,8 @@
 :jtalert: http://ham-apps.com[JT-ALERT-X]
 :cty_dat: http://www.country-files.com/cty/[here].
 
-// These [[X?]] numbers are HTML anchors, and can be used to
+// These [[xxxx]] labels are HTML anchors, and can be used to
-// navigate though the document easily: <<[X1],See Introduction]>> will
+// navigate though the document easily: <<[INTRO],See Introduction]>> will
 // place a hyper-link in your text to take you too the anchored section.
 // All major sections or points of interest should have one.
 
@@ -39,29 +39,29 @@
 // be section 1.1.1. This method is used throughout the document.
 
 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
-[[X1]]
+[[INTRO]]
 == Introduction
 include::introduction.adoc[]
 
-[[X2]]
+[[SYSREQ]]
 == System Requirements
 include::system-requirments.adoc[]
 
-[[X3]]
+[[INSTALL]]
 == Installation
 
 - Download _WSJT-X_ from the {homepage}. Click on _WSJT-X_ at the left
 margin and then on the appropriate link(s) for your operating system.
 
+[[INSTALL_WIN]]
 === Windows
 include::install-windows.adoc[]
 
-[[X31]]
+[[INSTALL_UBU]]
 === Linux
 include::install-ubuntu.adoc[]
 
-// The Mac Section need to be written. The file is a placeholder only.
+[[INSTALL_OSX]]
-[[X32]]
 === OS X
 include::install-mac.adoc[]
 
@@ -70,133 +70,147 @@ include::install-mac.adoc[]
 // Also, all the Qt4 stuff is now obsolete, and needs to be updated.
 // Instructions for source builds Win, *Nix & Mac all need to be written / 
 // Rreviewd.
-[[X33]]
+
+[[SRC_CODE]]
 === Source Code
 include::install-from-source.adoc[]
 
-[[X4]]
+[[CONFIG]]
 == Setup and Configuration
 
-[[X41]]
+[[STATION]]
 === Station Tab
 include::configuration-station.adoc[]
 
-[[X42]]
+[[TXMACROS]]
 === Tx Macros Tab
 include::configuration-txmacros.adoc[]
 
-[[X43]]
+[[BAND_SETTINGS]]
 === Band Settings Tab
 include::configuration-band-settings.adoc[]
 
-[[X44]]
+[[CONFIG_MAIN]]
 === Main Window
 include::configuration-main-window.adoc[]
 
-[[X45]]
+[[FONTS]]
 === Font Sizes
 include::font-sizes.adoc[]
 
-[[X5]]
+[[TUTORIAL]]
 == Basic Operating Tutorial
-[[X51]]
+
+[[TUT_MAIN]]
 === Main Window Settings
 include::tutorial-main-window.adoc[]
 
-[[X52]]
+[[TUT_WIDE_GRAPH]]
 === Wide Graph Settings
 include::tutorial-wide-graph-settings.adoc[]
 
-[[X53]]
+[[TUT_EX1]]
 === Sample File 1
 include::tutorial-example1.adoc[]
 
-[[X54]]
+[[TUT_EX2]]
 === Sample File 2
 include::tutorial-example2.adoc[]
 
-[[X55]]
+[[TUT_XCVR]]
 === Transceiver Setup
 include::transceiver-setup.adoc[]
 
-[[X6]]
+[[MAKE_QSOS]]
 == Making QSOs
 include::make-qso.adoc[]
 
-[[X7]]
+[[CONTROLS]]
 == Controls & Functions
 
-[[X71]]
+[[CONTROLS_WIDE]]
 === Wide Graph Controls
 include::controls-functions-wide-graph.adoc[]
 
-[[X72]]
+[[CONTROLS_MAIN]]
 === Main Window
 include::controls-functions-main-window.adoc[]
 
-[[X73]]
+[[CONTROLS_LEFT]]
 === Misc Controls Left
 include::controls-functions-left.adoc[]
 
-[[X74]]
+[[CONTROLS_CENTER]]
 === Misc Controls Center
 include::controls-functions-center.adoc[]
 
-[[X75]]
+[[CONTROLS_MSGS]]
 === Tx Messages
 include::controls-functions-messages.adoc[]
 
-[[X76]]
+[[STATUS_BAR]]
 === Status Bar
 include::controls-functions-status-bar.adoc[]
 
-[[X77]]
+[[MENUS]]
 === Menus
 include::controls-functions-menus.adoc[]
 
-[[X78]]
+[[SHORTCUTS]]
 === Keyboard Shortcuts
 include::controls-functions-kb-shortcuts.adoc[]
 
-[[X79]]
+[[MOUSE_COMMANDS]]
 === Mouse Commands
 include::controls-functions-special-mouse-cmds.adoc[]
 
-[[X8]]
+[[COOP_PGMS]]
-== JT65 Protocol
+== Cooperating Programs
+To be added ...
+
+[[JT65PRO]]
+== The JT65 Protocol
 include::jt65-protocol.adoc[]
 
-[[X9]]
+[[JT9PRO]]
-== JT9 Protocol
+== The JT9 Protocol
 include::jt9-protocol.adoc[]
 
-[[XA]]
+[[JT65_JT9]]
 == JT65 & JT9 Differences
 include::jt65-jt9-differences.adoc[]
 
-[[XB]]
+[[TXRX]]
 == Transmitting and Receiving in _WSJT-X_
 include::tx-rx.adoc[]
 
-[[XAPPA]]
+[[TROUBLE_SHOOTING]]
+== Troubleshooting
+To be added ...
+
+[[FAQ]]
+== Frequently Asked Questions
+To be added ...
+
+[[APPA]]
 == Appendix A
 
 // Note to Dev-Team, this list of files needs to be updated.
-[[XAPPA1]]
+[[APPA1]]
 === Installed Files
 include::installed-files.adoc[]
 
-[[XAPPA2]]
+[[APPA2]]
 === Runtime Files
 include::runtime-files.adoc[]
 
-[[XAPPB]]
+[[APPB]]
 == Appendix B
-[[XAPPB1]]
+[[APPB1]]
 === Rig Configuration
 include::rig-config-main.adoc[]
 
-[[XACK]]
+[[ACK]]
 == Acknowledgments
 include::acknowledgements.adoc[]
 

mainwindow.cpp

@@ -1,4 +1,4 @@
-//---------------------------------------------------------- MainWindow
+//----------------------------------------------------------- MainWindow
 #include "mainwindow.h"
 #include "ui_mainwindow.h"