Working frequencies can be for all regions or for individual IARU
regions. This allows each mode band tuple to have one or more working
frequencies which can include local ones only offered when the user
configures their IARU region.
Change working frequency default suggestions to better fit in
FT8. General rule is FT8 is at JT65 -2kHz except where that is not
possible e.g. where that would fall into a segment not allocated for
narrow band data modes. For tight bands like top band sqeeze existing
JT65 and JT allocations to allow space for FT8.
NOTE: this change changes the WSPR frequency on 80m to allow access to
JA stations that currently have no allocation where it was placed.
ALSO NOTE: the JT65 and JT9 frequencies for 80m move down 6 kHz, again
to accommodate region 3 users. Other appliactions not within our
control should be asked to move in step when 1.8.0 is released.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7810 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change allows allocations for JT9+JT65 dual mode to be fine
tuned. This in turn will hopefully allow some space for the new FT8
mode to be shoehorned in on bands with little or no free space. For
example on top band users could set the lowest JT9 decode offset at
1000 Hz and set the FT8 default working frequency at 1.839 MHz. Thus
allowing 1000 Hz for JT65, 1000 Hz for JT9 and 1000 Hz for FT8.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7809 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The recent change to delay Tx audio until Commander reports PTT is
really asserted should not be done when a direct RTS or DTR PTT method
is being used. This does leave a remote chance of ALC overshoot
issues from audio starting too early so it is down to the user to set
an appropriate "Settings->Advanced->Tx Delay" to ensure safe
operating.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7774 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Reverted to default stack allocation for jt9.exe on Windows.
Tidied up FT8 decoder inteface to remove arguments that will probably
never be used.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7768 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Because Commander queues up CAT commands the timing of Tx audio was
not being correctly synchronized to the rig PTT. This change polls the
rig PTT state after changing PTT and waits for it to go to the
expected state. As it happens, just doing a query does most of the
synchronization as the query gets queued behind the PTT directive
within Commander, with the reply being delayed until the query
completes. This change goes further and checks the PTT state changes
within one second.
Note that users using Commander will should not suffer from ALC
overshoot issues on rigs that suffer such a problem since Tx audio now
only commences after the rig has switched to transmit. Users with
hardware sequencers may need to adjust their "Settings->Advanced->Tx
Delay" parameter, this change does not introduce any new timing hazard
but there may be a slight lengthening of the delay to Tx audio if the
rig reports PTT via CAT as the audio delay may now be timed from the
actual PTT on the rig rather than the assertion of RTS/DTR.
Still outstanding is the slow processing of Commander CAT requests
which can cause considerable delays before Tx audio can start.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7764 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Bill Somerville
Joe Taylor
Steven Franke