mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-16 09:01:59 -05:00
47b1586e29
19 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Bill Somerville
|
764d1baccc |
Do not wait for PTT report from DX Lab Suite Commander when using direct DTR or RTS PTT
The recent change to delay Tx audio until Commander reports PTT is really asserted should not be done when a direct RTS or DTR PTT method is being used. This does leave a remote chance of ALC overshoot issues from audio starting too early so it is down to the user to set an appropriate "Settings->Advanced->Tx Delay" to ensure safe operating. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7774 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
ff6b29f3df |
Synchronize with rig PTT state when using DX Lab Suite Commander
Because Commander queues up CAT commands the timing of Tx audio was not being correctly synchronized to the rig PTT. This change polls the rig PTT state after changing PTT and waits for it to go to the expected state. As it happens, just doing a query does most of the synchronization as the query gets queued behind the PTT directive within Commander, with the reply being delayed until the query completes. This change goes further and checks the PTT state changes within one second. Note that users using Commander will should not suffer from ALC overshoot issues on rigs that suffer such a problem since Tx audio now only commences after the rig has switched to transmit. Users with hardware sequencers may need to adjust their "Settings->Advanced->Tx Delay" parameter, this change does not introduce any new timing hazard but there may be a slight lengthening of the delay to Tx audio if the rig reports PTT via CAT as the audio delay may now be timed from the actual PTT on the rig rather than the assertion of RTS/DTR. Still outstanding is the slow processing of Commander CAT requests which can cause considerable delays before Tx audio can start. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7764 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
db111b6529 |
Read mode before attempting to change it when using DX Lab Suite Commander
This change is specifically to work around some surprising behaviour in the Elecraft K3[S] which suffers audio drop outs when null changes that might effect the internal DSP are processed. This manifests when a blind mode change is sent through Commander. Here we read the mode and only subsequently command a mode change if it is not what we expect. Blind mode changes were preferred with Commander until now since state queries through Commander are occasionally unreliable. This issue has been reported to Elecraft so may not be permanent if they can and will address it in the rig's firmware. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7565 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
43cdd1df3c |
Add deley to rig resolution detection with DX Lab Suite Commander
Commander queues rig control commands and can return stale or invalid results immediately after state change commands so this change waits a couple of seconds hoping that Commander gets around to polling the rig before we read back the state. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7564 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
ac859c8f68 |
Several rig control enhancements and fixes
Use the new DX Lab Suite Commander command option to stop Commander trying to change the rig Tx VFO mode when we don't want to. Requires a recent DX Lab Suite Commander version. All rig controllers can now detect 20Hz resolution rigs, still needs 2Hz resolution code which will be needed for the FT-891 AFAIK. Enhance the HRD interface to be able to use the alternative PTT command as found on most Kenwood rigs for audio source selection. Fix Icom data mode selection issues. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7357 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
424ed88645 |
Take advantage of the forthcommng DX Lab Commander enhancement
V12.2.6 of teh DX Lab Suite Commander finally has a way to suppress mode rationalization when setting the split Tx frequency. This now means that we can now honor the radio setting to not change the rig modulation mode. This should help with a number of rigs that require different modes on teh Tx and Rx VFOs for optimal wide band digital operation. This will also help with some rig and interface combinations that lock up or otherwise misbehave when setting the Tx VFO mode at certain times with respect to other rig control commands. This change also improves mode setting in general hopefully closing a few corner case issues when starting up and when transmitting for the first time in a session. Included is the latest DX Lab Suite Commander TCP/IP commands documentation correct for v12.2.6. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7030 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
2cfbb15b4f |
Rig control overhaul to implement generic Doppler shift tracking
The concept of a nominal receive and transmit frequency has been
introduced. This is used as a base frequency for Doppler correction,
frequency setting and reporting. The start up frequency is now zero
which is updated by the first rig control status report. This needs
more work to accommodate calling frequency plus working frequency
operation as is used for random MS operation etc..
The main window frequency display now shows the transmit dial
frequency while transmitting.
The mode changing logic sequence has been changed such that the rig is
correctly put into and taken out of split mode as required by the
target mode. This also avoids the "other" VFO having its frequency
changed when entering a mode that does not use split operating like
WSPR.
The main window band combo box edit may now be used to input an kHz
offset from the current MHz dial frequency. This is intended for
setting a sked or working frequency on the VHF and up bands. For
example the working frequency for 23cms might be set to 1296MHz and a
working frequency of 1296.3MHz would be selected by selecting the
23cms band with the combo box drop down list and then entering 300k
into the band combo box edit widget.
When using JT4 modes a CTRL+Click on the waterfall adjusts the nominal
frequency such that the frequency clicked on becomes the Tx and Rx
frequency using the fixed 1000Hz DF that JT4 modes use. This will
probably be extended to all QSO modes when used in VHF & up mode. This
assumes that 1000Hz is an optimal DF for both Tx and Rx and therefore
one can "net" to an off frequency, but visible on the waterfall,
caller with one click.
Improvements to OmniRig rig control including use of the serial port
control lines RTS or DTR, on the CAT serial port used by OmniRig, for
PTT control.
Incrementing transaction sequence numbers added to messages to and from
the rig control thread. This enables round trip status to be tracked
and associated with a request. For example a command that might cause
several asynchronous status updates can now be tracked in the
originating thread such that it is clear which updates are caused by
executing the request. This in turn allows updates to be held until
the request is complete i.e. the state is consistent with the results
of the request.
Messages to the rig control thread are now posted as a new state
(Transceiver::TransceiverState) object. The rig control thread tracks
requests and actions any differences between the prior requests and
the new state.
The rig control thread is now stored on the heap so that it can be
closed down and released as needed. Along with this the rig control
close down semantics are better defined avoiding some potential
deadlock situations.
If the rig is placed into split mode it will be reverted to simplex
mode when the rig connection is closed.
When using direct rig control via Hamlib, rigs that have A/B VFO
arrangements and no method to query the current VFO like many Icoms
and the Yaesu FT-817/857/897(D) series now have smarted frequency
updating requiring no VFO changes when changing the frequency. This
is particularly important when doing Tx Doppler correction to avoid
glitches.
The implementation of emulated split operating mode ("Fake It") is
simplified and improved.
A dummy Hamlib transceiver for PTT control on a separate port is no
long instantiated if CAT or VOX PTT control is selected.
The resolution and any rounding of the rig CAT frequency set and get
commands is determined automatically upon opening the rig connection.
This is needed to determine the rate of frequency updates for Doppler
tracking. It also allows the rig to be more accurately controlled.
Frequency calibration is calculated separately for the receive and
transmit frequencies.
Whether the rig modulation mode should be controlled is now a
constructor argument rather than being passed with individual rig
control requests.
Doppler shift correction is considerably enhanced with simpler
controls and much better rig control. A new mode of tracking called
"receive only" is introduced for those with rigs that cannot be QSY:ed
via CAT when transmitting. Such rigs have a Doppler correction
calculated for the middle of the next transmit period just before
transmission starts. While using Doppler tracking it is now possible
to adjust the sked frequency either using the new kHz offset feature
of the main window band combo box or by directly tuning the rig VFO
knob while holding down the CTRL key.
The astronomical data window that includes Doppler tracking control is
now opened and closed using a checkable menu item to avoid it being
accidentally closed.
Debug configuration rig control diagnostic messages now have a
facility argument for clearer and more standardized trace messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6590 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
|
||
|
Bill Somerville
|
a84b7cdfd3 |
------------------------------------------------------------------------
r5297 | bsomervi | 2015-04-26 17:26:54 +0100 (Sun, 26 Apr 2015) | 49 lines Various defect repairs and ambigous behaviour clarifications A regression introduced in v1.5.0-rc1 where PTT on an alternate serial port when using no CAT control is resolved. A regression introduced in v1.5.0-rc1 where the network server field was not being restored in the settings dialog has been resolved. In settings the "Test PTT" button is now styled by checked state. The "Test PTT" button is enabled without needing click "Test CAT" first when no CAT rig control is selected. Various parts of the settings dialog are now disabled when no CAT rig control is selected. These are the "Mode" group, the "Split Operation" group and the "Monitor returns to last used frequency" check box. None of these have any visible impact nor make sense without CAT rig control. Initialization and teardown of rig control internals has been revised to avoid several problems related to timing and when switching between different CAT settings. This includes improvements in having the operating frequency restored between sessions when not using CAT rig control. The initialization of OmniRig connections has been improved, unfortunately it is still possible to get an exception when clicking the "Test CAT" button where just clicking "OK" and leaving the settings dialog will probably work. Some unnecessary CAT commands output during direct rig control have been elided to reduce the level of traffic a little. The handling of some automatically generated free text messages used when the station is a type 2 compound callsign or is working a type 2 compound callsign has been improved. This is related to how a double click on a message of the form "DE TI4/N0URE 73" is double clicked. The new behaviour depends on whether the current "DX Call" matches the call in the message. This resolves the ambiguity as to whether this message is a sign off at the end of a QSO with current operator (a 73 message is generated) or a tail end opportunity where the message should be treated the same as a CQ or QRZ message (WSJT-X QSYs to the frequency, generates messages and selects message one ready to call). This still leaves some potential ambiguous behaviors in this complex area but selecting "Clear DX call and grid after logging" should resolve most of them. Rig control trace messages have been cleaned up and are now more helpful, less verbose and, tidier in the source code. ------------------------------------------------------------------------ Merged from the wsjtx-1.5 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5298 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
bb23bdc7b9 |
Accommodate new mode mnemonics from DX Labs with FlexRadio SDRs
DX Lab Suite Commander now returns "DIGU" and "DIGL" for AFSK modes rather than RTTY & RTTY-R. Merged from wsjtx-1.4 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4895 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
6a6e56b712 |
Set split mode before and after setting Tx frequency
Also cleaned up duplicate trace output. Using the DX Lab Suite Commander CAT interface with rigs like the TS-2000 requires that split mode be set after changing the Tx frequency. This is because setting teh Tx frequency disables split mode. With some Icom rigs the rig must be in split mode before setting the Tx frequency otherwise the Tx frequency change will not be honoured. To fix this the sequence set-split, set-tx-frequency, set-split must always be used to change the Tx frequency. Support for new DX Lab Suite Commander TCP/IP commands Dave AA6YQ has added two new commands to the Commander server to allow more reliable control. Requires DX Lab Suite Commander 11.1.4 or later. Ensure split Tx frequency agrees with UI before transmitting Ensure split works on Yaesu via Hamlib without breaking others Also improved class HamlibTransceiver debug trace messages. Merged r4776-r4779 from wsjtx-1.4 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4780 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
3b43a18362 |
Fix various fake split mode issues
Merged from wsjtx-1.4 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4573 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
44a67927a9 |
Use non localized get frequency commands with Commander
Commander sends invalid UTF-8 strings for numbers that contain group separators, e.g. non-break space U+00A0 in French regional number formats. Revert to old undocumented frequency query commands that always use '.' and ',' for number punctuation. Merged from wsjtx-1.4 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4519 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
7ff8b8329d |
Only poll split frequency if in split mode
Because PowerSDR for the FlexRadio rigs doesn't implement split or VFO B, querying the TX VFO in transceiver polls causes an error with them. This query is unecessary. Removing it will cause a delay of one poll period after split is set for the Tx frequency to appear. This should be harmless, if not then there is a possibility of querying split before the Tx frequency. This seems obvious but I believe the order matters with some rigs so it needs more investigation. Merged from wsjtx-1.4 branch. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4435 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
94337a2760 |
Tidy up DX Lab and HRD interface implementations
Applied techniques learned from dealing with HRD quirks and TCP/IP client issues on Windows to the DX Lab Suite Commander interface. These changes should hopefully make both the HRD and DX Lab Suite CAT interfacing more robust in the face of network and other latency issues or server failures. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4296 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
cf0f8e0b95 |
Similar TCP/IP retry mechanism for DX Lab as that used on with HRD.
Assume the defect requiring occasional retries of QTCPSocket::waitReadReady() is generic; the same retry mechanism as used in the HRD interface has been impelemnted in the DX Lab Suite Commander TCP/IP interface. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4295 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
d157c20016 |
Add those pesky MOC generated code includes that break libraries if
they are included by automoc. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4035 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
fbafa17b3b |
Added context information to Hamlib interface exception messages.
Enhanced TransceiverBase error exception type to allow for language translatable messages. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4033 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
2b966c14d1 |
Igonored CAT polls of RX frequency from Commander when transmitting as
they are unreliable on Icom radios. Simplified diagnostic output for HRD CAT interface and DX Labs Suite Commander CAT interface. Removed duplicate diagnostic message from configuration CAT control. git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3983 ab8295b8-cf94-4d9e-aec4-7959e3be5d79 |
||
|
Bill Somerville
|
9247e10115 |
Added support for use of "Standard" locations for writable files.
This allows writable files to be located in the "correct"
location for each platform rather than in the directory of
the executable which, in general, is not recommended or
allowed in some cases.
A preprocessor macro WSJT_STANDARD_FILE_LOCATIONS is used to
switch be tween old and new functionality, currently it is on
by default. It can be turned off by defining it to a false
value (0) or more simply with cmake-gui setting the option
with the same name. JTAlert can only work with the old
non-standard file locations until Laurie VK3AMA chooses to
support the new file locations.
Even if the above is not enabled; the QSettings file is
written to a user specific location so it will be shared by
all instances of the program (i.e. across upgrades). See
below for multiple concurrent instance support changes.
Added a command line parser module for Fortran.
Added 'lib/options.f90' to facilitate more complex argument
passing to jt9 to cover explicit file locations.
Changed the way multiple concurrent instances are handled.
This is to allow the program to be run multiple times from
the same installation directory.
A new wsjtx command line optional argument is available "-r"
or "--rig" which enables multiple concurrent instance
support. The parameter of the new option is a unique name
signifying a rig or equivalent. The name is used as the
shared memory segment key and in window titles. The name is
also used to access unique settings files and writable data
files like ALL.TXT and log files. No attempt has been made
to share these files between concurrent instances.
If "-r" or "--rig" is used without a parameter it still
enables multiple concurrent instance support for that
instance. All instances must use a unique parameter, one of
which may be empty.
The rig name is appended the
QCoreApplication::applicationName() for convenient usage like
window titles.
Set non Qt locale to "C".
This ensures that C library functions give consistent results
whatever the system locale is set to. QApplication follows
the system locale as before. Thus using QApplication and its
descendants like widgets and QString for all user visible
formating will give correct l10n and using C/C++ library will
give consistent formatting across locales.
Added top level C++ exception handling to main.cpp.
Because the new transceiver framework uses exceptions
internally, the main function now handles any exceptions that
aren't caught.
Retired devsetup, replaced with Configuration.
Configuration is a class that encapsulates most of the
configuration behavior. Because rig configuration is so
closely coupled with rig operation, Configuration serves as a
proxy for access to the rig control functions. See
Configuration.hpp for more details of the Configuration
interface.
Menu changes.
Various checkable menu actions moved from main menu to the
Configuration dialog. The whole settings menu has been
retired with the single "Settings..." action moved to the
file menu for consistency on Mac where it appears as
"Preferences" in line with Mac guidelines.
New data models for data used by the application.
ADIF amateur band parameters, free text message macros, spot
working frequencies and, station information (station
descriptions and transverter offsets per band) each implement
the QAbstractItemModel interface allowing them to be used
directly with Qt view widgets (Bands.hpp, FrequencyList.hpp
and, StationList.hpp). Configuration manages maintenance of
an instance of all but the former of the above models. The
ADIF band model is owned by Configuration but requires no
user maintenance as it is immutable.
Band combo box gets more functionality.
This widget is now an editable QComboBox with some extra
input capabilities.
The popup list is still the list of spot working frequencies,
now showing the actual frequency decorated with the band
name. This allows multiple spot frequencies on a band if
required.
The line edit allows direct frequency entry in mega-Hertz
with a completer built in to suggest the available spot
working frequencies. It also allows band name entry where
the first available spot working frequency is selected.
Recognized band names are those that are defined by the ADIF
specification and can be found in in the implementation of
the ADIF bands model (Bands.cpp).
If an out of band frequency is chosen, the line edit shows a
warning red background and the text "OOB". Out of band is
only defined by the ADIF band limits which in general are
wider than any entities regulations.
Qt 5.2 now supports default audio i/p and o/p devices.
These devices are placeholders for whatever the user defines
as the default device. Because of this they need special
treatment as the actual device used is chosen at open time
behind the scenes.
Close-down behavior is simplified.
The close-down semantics were broken such that some objects
were not being shut down cleanly, this required amendments to
facilitate correct close down of threads.
User font selection added to Configuration UI.
Buttons to set the application font and the font for the band
and Rx frequency activity widgets have been added to the
Configuration UI to replace the file based font size control.
Free text macros now selected directly.
The free text line edit widgets are now editable combo boxes
that have the current free text macro definitions as their
popup list. The old context menu to do this has been
retired.
Astronomical data window dynamically formatted and has font a chooser.
This window is now autonomous, has its own font chooser and,
dynamically resizes to cover the contents.
Double click to Tx enabled now has its own widget in the status bar.
QDir used for portable path and file name handling throughout.
The "Monitor", "Decode", "Enable Tx" and, "Tune" buttons are now
checkable.
Being checkable allows these buttons control their own state
and rendering.
Calls to PSK Reporter interface simplified.
In mainwindow.cpp the calls to this interface are
rationalized to just 3 locations.
Manipulation of ALL.TXT simplified.
Moved, where possible, to common functions.
Elevated frequency types to be Qt types.
Frequency and FrequencyDelta defined as Qt types in their
meta-type system (Radio.hpp). They are integral types for
maximum accuracy.
Re-factored rig control calls in mainwindow.cpp.
The new Configuration proxy access to rig control required
many changes (mostly simplifications) to the MainWindow rig
control code. Some common code has been gathered in member
functions like qsy(), monitor(), band_changed() and
auto_tx_mode().
Rig control enhancements.
The rig control for clients interface is declared as an
abstract interface (See Transceiver.hpp). Concrete
implementations of this interface are provided for the Hamlib
rig control library, DX Lab Suite Commander via a TCP/IP
command channel, Ham Radio Deluxe also via a TCP/IP command
channel and, OmniRig via its Windows COM server interface.
Concrete Transceiver implementations are expected to be moved
to a separate thread after construction since many operations
are blocking and not suitable for running in a GUI thread.
To facilitate this all instantiation of concrete Transceiver
instances are handled by Configuration using a factory class
(TransceiverFactory) for configuration parameter based
instantiation.
Various common functionality shared by different rig
interface implementations are factored out into helper base
classes that implement or delegate parts of the Transceiver
interface. They are TransceiverBase which caches state to
minimize expensive rig commands, it also maps the Transceiver
interface into a more convenient form for implementation
(template methods). PollingTransceiver that provides a state
polling mechanism that only reports actual changes.
EmulateSplitTransceiver that provides split operation by
QSYing on PTT state changes.
EmulateSplitTransceiver can be used with any implementation
as it follows the GoF Decorator pattern and can wrap any
Transceiver implementation.
OmniRigTransceiver is derived directly from TransceiverBase
since it doesn't require polling due to its asynchronous
nature. OmniRigTransceiver is only built on Windows as it is
a COM server client. To build it you must first install the
OmniRig client on the development machine
(http://www.dxatlas.com/omnirig/).
DXLabSuiteCommanderTransceiver derives from
PollingTransceiver since it is a synchronous communications
channel. No third party library is required for this
interface.
HRDTransceiver also derives from PollingTransceiver. The HRD
interface library has been reverse engineered to provide
functionality with all available versions of HRD. No third
party libraries are required.
HamlibTransceiver likewise derives from PollingTransceiver
since the Hamlib asynchronous interface is non-functional.
Although this class will interface with the release version
of Hamlib (1.2.15.3); for correct operation on most rigs it
needs to run with the latest master branch code of Hamlib.
During development many changes to Hamlib have been submitted
and accepted, hence this requirement. Hamlib source can be
obtained from git://git.code.sf.net/p/hamlib/code and at the
time of writing he master branch was at SHA 6e4432.
The Hamlib interface directly calls the "C" interface and the
modified rigclass.{h,cpp} files have been retired.
There is a rig type selection of "None" which may be used for
non-CAT rigs, this is actually a connection to the dummy
Hamlib device.
PollingTransvceiver derives from TransceiverBase and
TransceiverBase derives from the Transceiver interface.
Each interface implementation offers some possibility of PTT
control via a different serial port than the CAT port. We
also support PTT control directly via a second serial port.
This is done by delegating to a dummy Hamlib instance which
is only used for PTT control. This means that
DXLabSuiteCommanderTransceiver, HRDTransceiver and
OmniRigTransceiver always wrap a dummy HamlibTransceiver
instance. The factory class TransceiverFactory manages all
these constructional complexities.
Serial port selection combo boxes are now editable with a
manually entered value being saved to the settings file.
This allows a non-standard port device to be used without
having to edit the settings file manually.
For TCP/IP network CAT interfaces; the network address and
port may be specified allowing the target device to be
located on a different machine from the one running wsjtx if
required. The default used when the address field is left
blank is the correct one for normal usage on the local host.
Selecting a polling interval of zero is no longer possible,
this is because the rig control capability can no longer
support one way connection. This is in line with most other
CAT control software.
In the Configuration dialog there are options to select split
mode control by the software and mode control by the
software. For the former "None", "Rig" and "Fake it" are
available, for the latter "None", "USB" and, "Data" are
available. Because tone generation is implicitly linked to
split mode operation; it is no longer possible to have the
software in split mode and the rig not or vice versa. This
may mean some rigs cannot be used in split mode and therefore
not in dual JT65+JT9 until issues with CAT control with that
rig are resolved. Single mode with VOX keying and no CAT
control are still possible so even the most basic transceiver
setup is supported as before.
Configuration now supports a frequency offset suitable for
transverter operation. The station details model
(StationList.hpp) includes a column to store an offset for
each band if required.
CMake build script improvements.
The CMakeLists.txt from the 'lib' directory has been retired
with its contents merged into the top level CMakeLists.txt.
Install target support has been greatly improved with the
Release build configuration now building a fully standalone
installation on Mac and Windows. The Debug configuration
still builds an installation that has environment
dependencies for external libraries, which is desirable for
testing and debugging.
Package target support is largely complete for Mac, Windows
and, Linux, it should be possible to build release installers
directly from CMake/CPack.
Cmake FindXXXX.cmake modules have been added to improve the
location of fftw-3 and Hamlib packages.
Version numbers are now stored in Versions.cmake and work in
concert with automatic svn revision lookup during build. The
version string becomes 'rlocal'± if there are any uncommitted
changes in the build source tree.
Moved resource like files to Qt resources.
Because location of resource files (when they cannot go into
the installation directory because of packaging rules) is
hard to standardize. I have used the Qt resource system for
all ancillary data files. Some like kvasd.dat are dumped out
to the temp (working directory) because they are accessed by
an external program, others like the audio samples are copied
out so they appear in the data directory under the default
save directory.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3929 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
|