Working frequencies can be for all regions or for individual IARU
regions. This allows each mode band tuple to have one or more working
frequencies which can include local ones only offered when the user
configures their IARU region.
Change working frequency default suggestions to better fit in
FT8. General rule is FT8 is at JT65 -2kHz except where that is not
possible e.g. where that would fall into a segment not allocated for
narrow band data modes. For tight bands like top band sqeeze existing
JT65 and JT allocations to allow space for FT8.
NOTE: this change changes the WSPR frequency on 80m to allow access to
JA stations that currently have no allocation where it was placed.
ALSO NOTE: the JT65 and JT9 frequencies for 80m move down 6 kHz, again
to accommodate region 3 users. Other appliactions not within our
control should be asked to move in step when 1.8.0 is released.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7810 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
When using split operating and/or rig mode setting there is a delay
before PTT is asserted while the CAT commands are processed. There
will even be a small delay if CAT is only used for PTT. This change
waits for these commands to be completed before starting the user Tx
delay specified in the settings.
There is a notable exception to this in that DX Lab Suite Commander
does not give us a way of knowing when CAT commands have actually been
completed. This combined with the way that Commander spaces CAT
commands, rather than being paced by the rig's CAT responses, means
that delays of more than 1 second are likely. As most rigs suffer some
sort of ALC overshoot when PTT is asserted with audio already present,
it is strongly recommended not to use the DX Lab Suite Commander as a
rig control proxy if your rig may suffer ALC overshoot and you use an
external PA. Please note that using a typical RF power meter to detect
ALC overshoots is unwise as they are rarely fast enough. It is
probably wise to assume that all rigs suffer ALC overshoot since it is
very difficult to design an ALC loop that avoids it.
This change also increases the range of the "Settings->Advanced->Tx
Delay" spin box to 0s up to 2s.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7756 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
These were using a hijacked custom spin box that was designed only for
letters i.e. submodes. Now there are two new custom spin boxes.
HistedSpinBox:- can be set with a list of integer values which the
step up and down will follow. Optionally limits the maximum and
minimum value to the upper and lower bounds of the values set. Note
that intermediate values are still valid.
RestrictedSpinBox:- more like a combo box because the provided values
are the only ones that can be set.
HintedSpinBox is used for the frequency tolerance and
RestrictedSpinBox is used for T/R period.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7698 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
More to come on this but should get Tab 2 basically working with
MSK144 running from a calling frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7675 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Ctrl+M (Cmd+M) was being used as a menu shortcut and in key press
event handlers which leads to inconsistent behaviour on some
platforms. Removed menu action shortcut.
Also tidied up handling of the hide controls menu action by making it
a checkable action and using its checked state to store the control
hiding state.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7608 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Level meter range increased to 0-90 dB.
2. Level meter reading is independent of slider setting.
3. For a trial period: thermometer bar goes red if a 16-bit sample
is within 5 dB A/D limit.
4. Slider can be used to adjust levels sent to waterfall.
5. Tx6 message is selected on program startup.
Thanks to W9MDB for most of this code.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7596 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Use a header format for polynomial coefficients that includes the
valid X range in scaled terms and a count of the number of
coefficients.
Use double precision consistently for polynomial coefficients. This
includes formatting with sufficient DPs when writing to files.
Many changes to the equalization plots, more to come.
Add error handling for reading coefficient, plot and filter
files. This includes being backward compatible for old format
refspec.dat files with no header.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7578 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This builds on the static phase compensation in the MSK144 decoder and
the phase analysis and polynomial fitting capabilities also in teh
MSK144 decoder, by allowing captured data to be selected for phase
equalization from the WSJT-X UI.
Reads captured phase compensation curve estimate files containing
fitted polynomial coefficients and measured phase data from MSK144
receptions. Intent is to select a compensation curve that is from a
known transmitter like an SDR which have good phase linearity. Phase
plots and compensation polynomials may be viewed and compared with the
current compensation polynomial. A suitable polynomial can be applied
to be use in all further decoding of MSK144 signals.
Plots of the currently selected polynomial and its modified higher
order terms polynomial which is actually used in equalization (this
plot may be dropped - it is just for kicks at the moment). When a
captured phase analysis file is loaded plots of the measured phase and
the proposed best fit polynomial are shown.
Basic maintenance is also included allowing clearing and loading
captured plots and an option to revert to a flat no equalization
curve.
More to come on this as amplitude equalization is also possible, this
will probably be similar, maybe even plotted on the same graph with
dual axes for phase and amplitude. Amplitude correction from a
measured reference spectrum could be viewed and selected for
equalization for all modes. TBC...
This change also introduces the QCustomPlot 3rd party
widget. Currently this is statically linked from a qcp library built
by the WSJT-X CMake script. This will probably be migrated to a shared
object (DLL) build as a CMake external project, once some CMake script
re-factoring has been completed, which is more in line with the
QCustomPlot author's intentions. This will allow efficient reuse in
other tools shipped with WSJT-X.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7570 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Allow band drop down list to be used to select FreqCal frequencies,
also resets position in automatic cycle. Tidy up some unnecessary
code.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7486 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Menu item *Tools -> Execute frequency calibration cycle* is renamed and checkable. Cycling does not start until checked.
2. Ctrl+F10 now allows you to cycle manually through the list of calibration frequencies.
3. Calibration sequence lengths can be set to 5, 10, 15, or 30 s with the sbTR spinBox.
Also: don't set sbTR index to 0 when entering a slow mode.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7485 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Rx DF is now "real-time" adjusting the rig in concert with the
monitored DF.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7465 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Some default time signals have been added to the frequency list so a
base set can be obtained by resetting the frequency list,
alternatively they can be added ad hoc in the normal fashion.
FreqCal mode behavior is to select the lowest cal frequency upon
entering FreqCal mode and cycling through each cal frequency
repeatedly. Ctrl+F10 jumps directly to the next higher frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7463 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Deepest decode level should be selected automatically when switching
to JT4 or JT65 when VHF & up mode is on and either of averaging or
deep search are enabled.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7456 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Sub mode and fast mode flag are added to the UDP Status message and
Status messages after appropriate UI changes. MSK144 decodes produce
UDP Decode messages. Fast JT9 messages are treated similarly.
Currently ISCAT decodes are not posted as UDP Decode messages as they
do not fit well with the model.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7389 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The class NetworkAccessManager sub-classes QNetworkAccessManager
adding a message box to ask the user if SSL errors may be
ignored. Ignored errors are ignored in future server replies so that
the user is not asked about he same peer certificate chain repeatedly.
The cache is currently per process only and not persistent.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7361 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
... rather than the working frequency.
Users set their working frequency and specify a calling frequency as a
kHz offset into the current Rx MHz with the main window spin box.
Calling CQ on the specified calling frequency is enabled by checking
the associated option.
Also enhanced the auto sequencing to handle short code 73 messages
correctly.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7339 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
display of the "No More Files..." message until after the "Decode Finished"
message is received.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7270 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change maintains the encapsulation of the MultiSettings class by
using a signal to notify clients of changes to the current
configuration name.
Modifications to the MainWindow class to display the current
configuration name in the status bar, if it is not "Default", based on
MultiSettings events rather than polling for changes.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7257 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
way to make sure that the new .wav file is ready, before starting wsprd?)
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7242 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
of power settings for Transmit and Tune. Also an interim update of
v1.7_Features.txt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7229 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Do not adjust Rx Freq automatically after an MSK144 decode.
3. Insert the Rcvd report in log window.
4. Send MSK144 decodes to PSK Reporter.
NB: not all these are fully tested, yet.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7134 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
I believe file saving and auto-sequencing nor work. Not sure about posting
to PSK reporter: please check.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7112 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Clean up mskrtd to remove unused variables.
2. Re-instate Rx frequency spinbox in MSK144 mode to allow decoding of off-frequency signals with small FTol. Make changes needed to pass Rx Freq in to fortran routines.
3. Enable realtime decoder for testing. Auto sequence does not yet work when realtime decoding is enabled. There are probably other bugs as well.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7109 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Move cursor DT readout to lower left of top panel.
3. More work on pick-decodes... but it's not yet fully working.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7092 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This button pops up the same context menu as the configurations button
on the main window menu bar. This allows the operator to easily escape
from an incorrectly configured configuration without changing it.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7075 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Fix the improper display of "Fast" checkbox.
Disable "CQ nnn" checkbox if MyCall is not K1JT or K9AN.
Use AppDir as path to execute the LDPC encode program.
Don't display submodes in mode label for JTMSK, MSK144.
Make Rx Freq spinner invisible in MSK144 mode.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7001 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
NB: temporary files are being written to execution directory!
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6989 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Two new validator classes CallsignValidator and
MaidenheadLocatorValidator are introduced and used in the
Configuration and MainWindow implementations.
MaidenheadLocatorValidator supports different lengths and minimum
required lengths with a default of subsquare with square being
required.
The message_aggregator application has been enhanced to show the
current DX call and DX grid as shown in the WSJT-X main window.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6903 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Instead of using the Qt QMessageBox class directly a new class
MessageBox (MessageBox.hpp) has been added to deal with platform
independence issues like the title not being shown on Mac OS X.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6861 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Rationalize the status bar construction and maintenance.
Ensure that incoming UDP Reply messages reset the watchdog.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6847 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The watchdog configuration is now a spin box of minutes with a special
first value of disabled. WSJT-X counts down minutes on the minute, if
the countdown reaches zero any attempt to transmit is aborted. The
countdown is reset by any mouse press or key press event inside the
main window or if the Tx message changes (auto sequencing).
The status bar now shows the Tx watchdog countdown if it is
active. This information is shown to the right of the progress bar
text.
The warning message boxes triggered within the GUI update routine now
no longer block the GUI updates.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6840 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Fixed naming of fast recording files.
Tidied some signal/slot plumbing in the fast plotter.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6806 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change corrects timing discrepancies on the horizontal fast
spectrum plot.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6780 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
These were discovered when running under teh valgrind MemCheck tool. I
have also checked in a suppressions file (wsjtx-valgrind.linux.supp)
suitable for use on Linux when running the valgrind MemCheck tool.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6755 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Refactor the save WAV file routine to return an error string as a
promise and then get that result and report in a QMessageBox.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6752 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Pass file path for peg-128 files to fast_decode(). (Inelegant, but it works.)
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6741 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Build now creates and installs a UDP library that contains the server
side of the UDP messaging facility. This library is used by the
udp_daemon and message_aggregator reference examples. The new library
is currently a static archive but can also be built as a shared
library. The library allows third party Qt applications to easily
access UDP messages from WSJT-X.
Refactored the message_aggregator reference example to split out
classes into separate translation units. Added new functionality to
exercise the new UDP status fields, highlight own call, CQ/QRZ
messages and decodes near Rx DF.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6691 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Static storage variables that should have been class members are made
so. This ensures that if they are used as initialization one time
switches then they will operate correctly when their class
instantiated more than once. This now happoens for most classes due to
the configurations switching facility which destroys all windows and
re-instantiates them.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6661 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Changing configuration causes WSJT-X and JTAlert to get into a fight
for the temporary directory. By moving the creation and clearup of the
temporary directory outside of the configurations loop this issue is
minimized to no worse than before multiple configurations were added.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6630 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Multiple configurations are accessed and maintained from a new main
window menu bar pop up menu "Configurations". The prior settings are
the "Default" entry. New configurations may be added by cloning
existing ones. Maintenance and navigation is via sub menus for each
configuration.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6623 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The concept of a nominal receive and transmit frequency has been
introduced. This is used as a base frequency for Doppler correction,
frequency setting and reporting. The start up frequency is now zero
which is updated by the first rig control status report. This needs
more work to accommodate calling frequency plus working frequency
operation as is used for random MS operation etc..
The main window frequency display now shows the transmit dial
frequency while transmitting.
The mode changing logic sequence has been changed such that the rig is
correctly put into and taken out of split mode as required by the
target mode. This also avoids the "other" VFO having its frequency
changed when entering a mode that does not use split operating like
WSPR.
The main window band combo box edit may now be used to input an kHz
offset from the current MHz dial frequency. This is intended for
setting a sked or working frequency on the VHF and up bands. For
example the working frequency for 23cms might be set to 1296MHz and a
working frequency of 1296.3MHz would be selected by selecting the
23cms band with the combo box drop down list and then entering 300k
into the band combo box edit widget.
When using JT4 modes a CTRL+Click on the waterfall adjusts the nominal
frequency such that the frequency clicked on becomes the Tx and Rx
frequency using the fixed 1000Hz DF that JT4 modes use. This will
probably be extended to all QSO modes when used in VHF & up mode. This
assumes that 1000Hz is an optimal DF for both Tx and Rx and therefore
one can "net" to an off frequency, but visible on the waterfall,
caller with one click.
Improvements to OmniRig rig control including use of the serial port
control lines RTS or DTR, on the CAT serial port used by OmniRig, for
PTT control.
Incrementing transaction sequence numbers added to messages to and from
the rig control thread. This enables round trip status to be tracked
and associated with a request. For example a command that might cause
several asynchronous status updates can now be tracked in the
originating thread such that it is clear which updates are caused by
executing the request. This in turn allows updates to be held until
the request is complete i.e. the state is consistent with the results
of the request.
Messages to the rig control thread are now posted as a new state
(Transceiver::TransceiverState) object. The rig control thread tracks
requests and actions any differences between the prior requests and
the new state.
The rig control thread is now stored on the heap so that it can be
closed down and released as needed. Along with this the rig control
close down semantics are better defined avoiding some potential
deadlock situations.
If the rig is placed into split mode it will be reverted to simplex
mode when the rig connection is closed.
When using direct rig control via Hamlib, rigs that have A/B VFO
arrangements and no method to query the current VFO like many Icoms
and the Yaesu FT-817/857/897(D) series now have smarted frequency
updating requiring no VFO changes when changing the frequency. This
is particularly important when doing Tx Doppler correction to avoid
glitches.
The implementation of emulated split operating mode ("Fake It") is
simplified and improved.
A dummy Hamlib transceiver for PTT control on a separate port is no
long instantiated if CAT or VOX PTT control is selected.
The resolution and any rounding of the rig CAT frequency set and get
commands is determined automatically upon opening the rig connection.
This is needed to determine the rate of frequency updates for Doppler
tracking. It also allows the rig to be more accurately controlled.
Frequency calibration is calculated separately for the receive and
transmit frequencies.
Whether the rig modulation mode should be controlled is now a
constructor argument rather than being passed with individual rig
control requests.
Doppler shift correction is considerably enhanced with simpler
controls and much better rig control. A new mode of tracking called
"receive only" is introduced for those with rigs that cannot be QSY:ed
via CAT when transmitting. Such rigs have a Doppler correction
calculated for the middle of the next transmit period just before
transmission starts. While using Doppler tracking it is now possible
to adjust the sked frequency either using the new kHz offset feature
of the main window band combo box or by directly tuning the rig VFO
knob while holding down the CTRL key.
The astronomical data window that includes Doppler tracking control is
now opened and closed using a checkable menu item to avoid it being
accidentally closed.
Debug configuration rig control diagnostic messages now have a
facility argument for clearer and more standardized trace messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6590 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Samples are downloaded from a web server, currently the SF download
server. The samples are stored in the source controlled samples
directory and the CMake script there builds a suitable directory tree
for upload to the web server under samples/web containing the samples
hierarchy and the generated JSON contents database file. The samples
CMake script also defines an 'upload-samples' target that uses rsync
to efficiently upload the samples and the accompanying contents JSON
database file.
Any directory structure under the samples directory may be created, to
add a new sample file simply add the file to source control and amend
the list of sample files (SAMPLE_FILES) in samples/CMakeLists.txt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6308 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Also use correct C binding and have compilers determine sizes and
offsets.
The wsjtx.exe program now owns the decoder shared data that is shared
with symspec. It is now in struct dec_data, still a global variable
for now but hopefully a MainWindow member variable soon.
The struct dec_data (in both C/C++ and Fortran) has a sub structure
with the decoder parameters which enables copying and manipulating a
lot cleaner.
New of changed types of shared data must still be modified in
commons.h and a new file lib/jt9com.f90, they must stay in sync as a
pointer to the structure is passed between C and Fortran.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6290 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Set tune power with SHIFT + "Pwr" slider. SHIFT + "Pwr" slider to top
cancels separate power level for tune. Smarter tool tip for "Pwr"
slider.
Needs User Guide update if change is acceptable.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6284 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The message_aggregator (MessageAggregator.cpp) has been updated to do
something with WSPR decodes.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6101 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
There are several object lifetime issues that can cause crashes on
application close down. This change is the first phase of addressing
these issues.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5719 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The Rx meter is now a better Qt citizen and can be resized. Added a
more obvious peak signal indicator. It is now a custom widget derived
from QFrame and is now directly added via promotion in Designer.
Added a custom widget to act as a letter spin box, this is used for
sub mode control. Switched the frequency tolerance widget to a combo
box with preset values so that it is more uniform across systems and
font sizes.
Added container widgets for group control of various UI widgets such
as QSO controls, DX call controls and WSPR controls. Introduced a
stacked widget to allow the WSPR controls to be swapped in in place of
the "QSO" controls. The "QSO" controls are are the Rx, Tx and related
controls along with the main tab widget with the message buttons and
fields. This means that the WSPR version of the main window (and EME
Echo mode) are now much cleaner.
Increased the size of the rig control widget and styled its colour
using a dynamic property so that it can be defined in the Designer UI
definition. Reinstated it as a push button to do a rig control reset
and retry after an error.
Reset most UI widgets to default properties, particularly removing any
fixed sizes so that they can resize freely when fonts are changed. The
overall layout is now controlled almost exclusively by stretch factors
on some of the rows and columns of the various grid layout managers.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5630 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
For possible statistical analysis. N is the number of decoded signals.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5599 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
visible in Echo mode. Reset nsum=0 when Tx Enable is toggled ON in Echo mode.
Don't restart Monitor after finishing a sequence of Echo transmissions.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5584 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Improved astronomical data and Doppler tracking control window widgets
and layout management to make it more platform independent and font
change tolerant.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5580 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Make WSPRnet.org spot uploads tolerant of network issues, spots still
get discarded for any period that has problems but now uploading
resumes on the next period.
Ensure that decoded text starts with correct font by not using the
base class append method directly.
Fixed a major memory leak in the WSPRNet class which was not freeing
processed request reply objects.
Added some helpful debug prints in WSPRnet.org spot processing.
Also tidied up a number of class implementations that were not
including he MOC generated code.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5560 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Also used it to implement the prefixes, shortcuts and mouse help
windows.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5554 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Also use a style sheet to set the font as widget level font settings
are overriden when the global default font is changed in settings.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5553 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Provide a dialog for band hopping scheduling which replaces tab
four. Ensure that split mode is not used for WSPR. Select the correct
tab for WSPR operation. Shift WSPR band hopping code out of the
MainWindow class.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5517 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Start to rationalize the new WSPR code with the data models.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5475 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Forbid consecutive Tx sequences.
Mark Tx sequences with horizontal yellow line in waterfall.
Reduce the wait time in msleep() command (mainwindow.cpp line 4342).
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5470 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Working frequencies are mode dependent and a reset to defaults button
has been added.
Also re-factored much of the model and item delegate code to simplify
several of the model implementations. Introduced a single routine
called from main to register the custom types with Qt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5453 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The generated and free text radio buttons now refresh the sent message
even if teh clicked radio button is already checked.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5444 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This merge brings the WSPR feature development into the main line
ready for release in a future v1.6 release.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5424 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
To facilitate interaction with other applications WSJT-X now sends
status updates to a predefined UDP server or multicast group
address. The status updates include the information currently posted
to the decodes.txt and wsjtx_status.txt files. An optional back
communications channel is also implemented allowing the UDP server
application to control some basic actions in WSJT-X.
A reference implementaion of a typical UDP server written in C++ using
Qt is provided to demonstrate these facilities. This application is
not intended as a user tool but only as an example of how a third
party application may interact with WSJT-X.
The UDP messages Use QDataStream based serialization. Messages are
documented in NetworkMessage.hpp along with some helper classes that
simplify the building and decoding of messages.
Two message handling classes are introduced, MessageClient and
MessageServer. WSJT-X uses the MessageClient class to manage outgoing
and incoming UDP messages that allow communication with other
applications. The MessageServer class implements the kind of code
that a potential cooperating application might use. Although these
classes use Qt serialization facilities, the message formats are
easily read and written by applications that do not use the Qt
framework.
MessageAggregator is a demonstration application that uses
MessageServer and presents a GUI that displays messages from one or
more WSJT-X instances and allows sending back a CQ or QRZ reply
invocation by double clicking a decode. This application is not
intended as a user facing tool but rather as a demonstration of the
WSJT-X UDP messaging facility. It also demonstrates being a multicast
UDP server by allowing multiple instances to run concurrently. This is
enabled by using an appropriate multicast group address as the server
address. Cooperating applications need not implement multicast
techniques but it is recomended otherwise only a single appliaction
can act as a broadcast message (from WSJT-X) recipient.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5225 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The feature to set the next message to be sent to auto generated
message number 6 (CQ) is now only trggered when a transmission of a 73
message is made for the first time in a QSO. If a second 73 message is
required, for example when a QSO partner repeats an RRR message after
your 73 message, simply double clicking the RRR message will initiate
another 73 message without triggering a log QSO dialog or setting the
next message to CQ.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5065 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
More consistent and accurate processing of compund callsigns including
recognizing the user's call in both base and fully qualified form,
extracting reports from special type one and type two compound call
messages. Ensure that "CQ DX" message prefixes are recognized and
processd correctly.
The cycle of double clicking through a QSO has been enhanced to
recognoize the standard messages correctly and use the correct next
message. The automatic transmission button "Enable Tx" now does what
it says and does not double as a stop transmit button. This allows the
current transmission to complete even if the automatic transmission
feature is disabled. In line with this the "stop sending after a 73
message is sent" feature turns off the automatic transmission enable
at the start of the sending of a 73 message and also the next message
is now set up as the CQ message automatically in this scenario. A 73
message is now either a standard message containing the word "73" or
any free text message containing "73" (not necessarily as a distinct
word").
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5055 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Wrapping the Ui:: UI class in a QScopedPointer, a perfectly proper
thing to do, causes QtDesigner to fail to grok the code.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5019 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Colours behave like other configuration items and changes are only
applied when the Settings UI is dismissed via the "OK" button.
Simplified font settings and use style sheets consistently to set the
application and decoded text fonts. This is necessary because any UI
widget that has a style sheet applied does not honor a font set by
QWidget::setFont() even if there is no font setting in the style
sheet, this is broken behaviour IMHO but that is the way Qt currently
works.
Use a style sheet to style the frequency display and clock. This is
necessary to allow fonts to be cascaded through parent style sheets
and still be overridden on these widgets.
Simplify the decoded text widgets, there is no need to use the
QTextBrowser as a super class since the simpler QTextEdit set as
read-only is sufficient. Also removed colour setting via a background
brush as it doesn't work and the HTML 'bgcolor' attribute works
correctly.
Change to UI properties of the decoded text widgets to allow
horizontal scrolling if required, this allows larger fonts to be used
without truncating decoded messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4957 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Pass the temporary directory to jt9 and use it to give the correct
paths to temporary files. Also jt9 passes the absolute path to
kvasd.dat in the temporary directory to kvasd.
Clear out all the annoying cruft that has accumulated due to having to
run with $CWD as the temporary directory.
Use QStandardPaths to find the writable data directory where needed
rather than passing it around between objects. This now works because
the $CWD hasn't been changed.
Do away with the CMake option WSJT_STANDARD_FILE_LOCATIONS as it is no
longer needed.
Fix astro status file azel.dat formatting.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4732 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Also complete the wrapper code in wisdom.c.
TBD: should be possible to use fftw3f.f03 instead of the ad hoc wisdom.c.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4617 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Routine packmsg now tries the shortlist (Type 1 prefix or suffix) first.
Then it tries to to make a valid message using a Type 2 prefix or suffix.
If both fail, it packs the first 13 characters as a free-text message.
The GUI now generates the most useful messages with compound callsigns
of all valid types.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4533 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Since the log files have moved to a hidden directory a menu action to
open the logs directory in a suitable system applicaiton is needed.
Added "Open log directory" to File manu bar pop up menu.
Merged from wsjtx-1.4 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4471 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Because of confilicts using the shared memory to communicate with jt9
only one instance of WSJT-X may run with each unique key (rig name).
Added a QLockFile for each unique key in the temp directory and logic
to deal with stale locks and retries.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4465 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
So that a manual can be viewed without an Internet connection a second
manual action has been added to the WSJT_X help menu. This shells out
to the default web browser with a local file target.
The build has been enhanced to install and package the current version
of the HTML user manual as downloaded from the project web site at
build time
The package file locations have been adjusted to be compatible with
the QStandardPaths class so that its locate() method can be used to
portably access resources like this local help file
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4359 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Some rigs either do not honour some CAT commands while transmitting or
interpret them incorrectly. To deal with this a settings option to
allow TX frequency changes while transmitting has been added with a
default value of off.
Any UI actions that directly or indirectly change the TX frequency are
guarded according to this new option. As well as this band changes and
use of the +2kHz check box are disabled and guarded respectively in
transmit mode.
Mode changes via the menu are now disabled while transmitting.
When TX frequency changes are allowed; frequency changes are correctly
implemented while in tune mode.
Double clicking decodes while transmitting now correctly regenerate
and change the message sent on the fly.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4349 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The Qt test mode that uses special paths for writeable files (via
QtStandardPaths) doesn't make a special temporary file path. This
change appends " - test_mode" to the WSJT-X unique temporary file path
so that an application run in test mode will not interact with another
running in normal mode.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4240 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Some non-modal help windows were not being automatically closed on
application exit.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4143 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
