Double-clicks on 73 messages fixed. Fixed issue with incorrect decode
being selected by double-click. Refined auto-sequencing sign off
handling, any 73 or rr73 free text near Rx or Tx frequency taken as a
73 from QSO partner but if a standard message then must be from QSO
partner.
Moved functionality from MainWindow to DecodedText class.
More efficient picking of messages from decoded text windows by
extracting the text block directly.
Tighten up use of RR73 and skipping Tx1, these are now disabled for
relevant compound calls where they would break the QSO exchange.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8056 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
73 messages from other QSOs on frequency should now be ignored rather
than being processed.
Also some long overdue refactoring and tidying of non-idiomatic C++
code in the logbook directory.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8047 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This means that "CQ DX", "CQ VT", etc., will be presistent until changed back.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8035 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Note that reverting to v1.7 will invalidate any saved working
frequencies from v1.8 but proceeding to v1.8 again will present a
reset set of working frequencies i.e. any user defined entries in v1.8
will be lost of a v1.8 -> v1.7 -> v1.8 transition is made.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8018 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Holding down the SHIFT key while tuning the rig should update the
nominal sked frequency, not holding done the SHIFT key should not
update the sked frequency. This is not yet perfect and sometimes a
change to the nominal sked frequency can get through but it is a rare
as yet unfound race condition.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7992 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Call first combined with "Lock Tx=Rx" (why would anyone consider doing
that!) should continue on the Tx frequency of the station being
worked and not be switched another calling station's frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7972 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
FT8 auto-stop will only react to messages within +/- 50Hz of our Tx
frequency.
Auto-sequence on "DE ..." and free text 73 messages will respond if
they are within 25Hz of our Tx or Rx frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7970 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Bad idea, need to find a better way to extend grids to 6-digits from
CALL3.TXT.
This reverts commit r7959
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7965 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Required to pick best AP masks in FT8 decoder
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7958 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The UDP decode and reply message have been augmented with a boolean
flag denoting a low confidence decode when set. Existing clients can
safely use the reply message without passing the flag as the default
value will still action messages that have high confidence. If low
confidence decodes are to be passed back via the reply message then
the low confidence flag must be included and correctly set to match
the original decode.
See NetworkMessage.hpp for message fields and meanings.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7957 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Enable or disable by double-clicking the Tx4 button or the adjacent
radio button. Is auto disabled by a band change as it is expected that
the user reassess the conditions to see if message repetitions are
unlikely to be needed.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7950 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Enable and disable by double-clicking the Tx1 button or the adjacent
radio button. Tx1 message shows grayed out when the Tx1 message is
elided.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7949 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Allow any message to start a QSO so long as we are not in an
auto-reply QSO.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7943 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
moves the Rx frequency to theirs, this facilitates calling a station
who is busy and may have many callers on their frequency. Updated the
corresponding mouse shortcuts help text.
Allow for times with seconds when parsing fast mode and FT8 decodes.
Exclude the RR73 grid square from and grid validation or matching, it
is not a grid square any more as far as WSJT-X is concerned, it is an
RRR substitute.
Add a simple state machine for QSO progress such that replies and
auto-sequencing can be better controlled.
Get compound callsign edge cases working again and allow QSOs from and
to compound callsign holders working in as many situations as possible
including auto-sequencing and FT8 auto-reply mode. This does mean
that a "DE W6/K1ABC DM93" type message close to a callers Tx or Rx
frequency will be taken as a reply to a CQ call despite it not being
explicitly addressed back to the CQ caller. Compound callsigns should
work in MSK144 contest mode also as well as in short code modes with
some minor restrictions (short codes will not be used where
configuration demands that a message be used to send a full compound
callsign).
Auto sequencing has been made generic such that it can be used for
more than one mode if desired.
Allow the use of free text messages to sign off in auto sequenced QSOs
without the message being overwritten by the sequencer. Double click
actions have been added to the Tx5 radio and push buttons to revert
back to the default standard 73 message.
Make DisplayText class interface more idiomatic C++ and simplify a
bit.
Fixed some displayed widget arrangements for different modes and
sub-modes so that they are consistent when starting up and when
switching mode or sub-mode.
This is a big change which has been extensively tested but no doubt
there will also be some new defects introduced.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7939 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. "Call 1st" label turns red when armed to respond to a caller.
3. Suppress some recognizable false decodes, send them to cumulative file
"data_dir/false_decodes.txt".
4. Reduce sleep delay in decoder() to 10 ms.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7928 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Thanks to Mike, W9MDB, for this contribution.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7921 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Avoid trying to set bogus uninitialized frequency values.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7897 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Now equlization tools as it covers both amplitude and phase
equalization.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7875 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change also adds seconds resolution to log files and log QSO
fields.
This change makes the log QSO dialog more layout friendly and uses a
QDateTimeEdit for QSO start and end times.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7827 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Working frequencies can be for all regions or for individual IARU
regions. This allows each mode band tuple to have one or more working
frequencies which can include local ones only offered when the user
configures their IARU region.
Change working frequency default suggestions to better fit in
FT8. General rule is FT8 is at JT65 -2kHz except where that is not
possible e.g. where that would fall into a segment not allocated for
narrow band data modes. For tight bands like top band sqeeze existing
JT65 and JT allocations to allow space for FT8.
NOTE: this change changes the WSPR frequency on 80m to allow access to
JA stations that currently have no allocation where it was placed.
ALSO NOTE: the JT65 and JT9 frequencies for 80m move down 6 kHz, again
to accommodate region 3 users. Other appliactions not within our
control should be asked to move in step when 1.8.0 is released.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7810 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
When using split operating and/or rig mode setting there is a delay
before PTT is asserted while the CAT commands are processed. There
will even be a small delay if CAT is only used for PTT. This change
waits for these commands to be completed before starting the user Tx
delay specified in the settings.
There is a notable exception to this in that DX Lab Suite Commander
does not give us a way of knowing when CAT commands have actually been
completed. This combined with the way that Commander spaces CAT
commands, rather than being paced by the rig's CAT responses, means
that delays of more than 1 second are likely. As most rigs suffer some
sort of ALC overshoot when PTT is asserted with audio already present,
it is strongly recommended not to use the DX Lab Suite Commander as a
rig control proxy if your rig may suffer ALC overshoot and you use an
external PA. Please note that using a typical RF power meter to detect
ALC overshoots is unwise as they are rarely fast enough. It is
probably wise to assume that all rigs suffer ALC overshoot since it is
very difficult to design an ALC loop that avoids it.
This change also increases the range of the "Settings->Advanced->Tx
Delay" spin box to 0s up to 2s.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7756 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
For FT8 mode:
1. Open LU 13 in the proper way.
2. Disable diagnostic LU 51.
3. Add keyboard shortcuts CTRL+Plus, CTRL-Minus, to adjust audio Tx frequency
in even 50 Hz steps.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7749 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This feature is of limited benefit and causes unexpected behaviour on
rigs with lower than 1Hz resolution. Removed for simplicity.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7743 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. ft8d is now a bare-bones multi-decoder.
3. wsjt-x now includes the bare-bones multi-decoder for FT8.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7729 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
