The watchdog configuration is now a spin box of minutes with a special
first value of disabled. WSJT-X counts down minutes on the minute, if
the countdown reaches zero any attempt to transmit is aborted. The
countdown is reset by any mouse press or key press event inside the
main window or if the Tx message changes (auto sequencing).
The status bar now shows the Tx watchdog countdown if it is
active. This information is shown to the right of the progress bar
text.
The warning message boxes triggered within the GUI update routine now
no longer block the GUI updates.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6840 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Qt does its best job laying out widgets consistently across platforms
if all unecessary constraints are removed. Widget layout policies can
almost always be used to achieve the required layout without reverting
to hard coded pixel values.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6759 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Pass file path for peg-128 files to fast_decode(). (Inelegant, but it works.)
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6741 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Multiple configurations are accessed and maintained from a new main
window menu bar pop up menu "Configurations". The prior settings are
the "Default" entry. New configurations may be added by cloning
existing ones. Maintenance and navigation is via sub menus for each
configuration.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6623 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The concept of a nominal receive and transmit frequency has been
introduced. This is used as a base frequency for Doppler correction,
frequency setting and reporting. The start up frequency is now zero
which is updated by the first rig control status report. This needs
more work to accommodate calling frequency plus working frequency
operation as is used for random MS operation etc..
The main window frequency display now shows the transmit dial
frequency while transmitting.
The mode changing logic sequence has been changed such that the rig is
correctly put into and taken out of split mode as required by the
target mode. This also avoids the "other" VFO having its frequency
changed when entering a mode that does not use split operating like
WSPR.
The main window band combo box edit may now be used to input an kHz
offset from the current MHz dial frequency. This is intended for
setting a sked or working frequency on the VHF and up bands. For
example the working frequency for 23cms might be set to 1296MHz and a
working frequency of 1296.3MHz would be selected by selecting the
23cms band with the combo box drop down list and then entering 300k
into the band combo box edit widget.
When using JT4 modes a CTRL+Click on the waterfall adjusts the nominal
frequency such that the frequency clicked on becomes the Tx and Rx
frequency using the fixed 1000Hz DF that JT4 modes use. This will
probably be extended to all QSO modes when used in VHF & up mode. This
assumes that 1000Hz is an optimal DF for both Tx and Rx and therefore
one can "net" to an off frequency, but visible on the waterfall,
caller with one click.
Improvements to OmniRig rig control including use of the serial port
control lines RTS or DTR, on the CAT serial port used by OmniRig, for
PTT control.
Incrementing transaction sequence numbers added to messages to and from
the rig control thread. This enables round trip status to be tracked
and associated with a request. For example a command that might cause
several asynchronous status updates can now be tracked in the
originating thread such that it is clear which updates are caused by
executing the request. This in turn allows updates to be held until
the request is complete i.e. the state is consistent with the results
of the request.
Messages to the rig control thread are now posted as a new state
(Transceiver::TransceiverState) object. The rig control thread tracks
requests and actions any differences between the prior requests and
the new state.
The rig control thread is now stored on the heap so that it can be
closed down and released as needed. Along with this the rig control
close down semantics are better defined avoiding some potential
deadlock situations.
If the rig is placed into split mode it will be reverted to simplex
mode when the rig connection is closed.
When using direct rig control via Hamlib, rigs that have A/B VFO
arrangements and no method to query the current VFO like many Icoms
and the Yaesu FT-817/857/897(D) series now have smarted frequency
updating requiring no VFO changes when changing the frequency. This
is particularly important when doing Tx Doppler correction to avoid
glitches.
The implementation of emulated split operating mode ("Fake It") is
simplified and improved.
A dummy Hamlib transceiver for PTT control on a separate port is no
long instantiated if CAT or VOX PTT control is selected.
The resolution and any rounding of the rig CAT frequency set and get
commands is determined automatically upon opening the rig connection.
This is needed to determine the rate of frequency updates for Doppler
tracking. It also allows the rig to be more accurately controlled.
Frequency calibration is calculated separately for the receive and
transmit frequencies.
Whether the rig modulation mode should be controlled is now a
constructor argument rather than being passed with individual rig
control requests.
Doppler shift correction is considerably enhanced with simpler
controls and much better rig control. A new mode of tracking called
"receive only" is introduced for those with rigs that cannot be QSY:ed
via CAT when transmitting. Such rigs have a Doppler correction
calculated for the middle of the next transmit period just before
transmission starts. While using Doppler tracking it is now possible
to adjust the sked frequency either using the new kHz offset feature
of the main window band combo box or by directly tuning the rig VFO
knob while holding down the CTRL key.
The astronomical data window that includes Doppler tracking control is
now opened and closed using a checkable menu item to avoid it being
accidentally closed.
Debug configuration rig control diagnostic messages now have a
facility argument for clearer and more standardized trace messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6590 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Make averaging and DS separately selecteble.
3. Clear nftt and avemsg on Clear Avg.
4. Allow fer65 to handle message averaging.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6543 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Samples are downloaded from a web server, currently the SF download
server. The samples are stored in the source controlled samples
directory and the CMake script there builds a suitable directory tree
for upload to the web server under samples/web containing the samples
hierarchy and the generated JSON contents database file. The samples
CMake script also defines an 'upload-samples' target that uses rsync
to efficiently upload the samples and the accompanying contents JSON
database file.
Any directory structure under the samples directory may be created, to
add a new sample file simply add the file to source control and amend
the list of sample files (SAMPLE_FILES) in samples/CMakeLists.txt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6308 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The header QMetaType must now be included explicitly if no other
header includes QObject.
Adjust band combo box layout settings to ensure it is rendered at
minimum content size otherwise it stretches the signal meter width to
an ugly extent.
Also retired the "frequencies" settings file key so that upgrades and
downgrades between 1.5 and 1.6 no longer require rebuilding the
working frequencies list.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5727 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Also enhanced delete .wav files menu entry to delete .c2 files as
well.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5672 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The Rx meter is now a better Qt citizen and can be resized. Added a
more obvious peak signal indicator. It is now a custom widget derived
from QFrame and is now directly added via promotion in Designer.
Added a custom widget to act as a letter spin box, this is used for
sub mode control. Switched the frequency tolerance widget to a combo
box with preset values so that it is more uniform across systems and
font sizes.
Added container widgets for group control of various UI widgets such
as QSO controls, DX call controls and WSPR controls. Introduced a
stacked widget to allow the WSPR controls to be swapped in in place of
the "QSO" controls. The "QSO" controls are are the Rx, Tx and related
controls along with the main tab widget with the message buttons and
fields. This means that the WSPR version of the main window (and EME
Echo mode) are now much cleaner.
Increased the size of the rig control widget and styled its colour
using a dynamic property so that it can be defined in the Designer UI
definition. Reinstated it as a push button to do a rig control reset
and retry after an error.
Reset most UI widgets to default properties, particularly removing any
fixed sizes so that they can resize freely when fonts are changed. The
overall layout is now controlled almost exclusively by stretch factors
on some of the rows and columns of the various grid layout managers.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5630 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This is now half way between the recent change to 30dB when the
formula was corrected to voltage attenuation from power and prior to
that.
Also corrected formula for the SoundOutput::attenuation property to
use the correct voltage attenuation calculation.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5579 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Provide a dialog for band hopping scheduling which replaces tab
four. Ensure that split mode is not used for WSPR. Select the correct
tab for WSPR operation. Shift WSPR band hopping code out of the
MainWindow class.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5517 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Working frequencies are mode dependent and a reset to defaults button
has been added.
Also re-factored much of the model and item delegate code to simplify
several of the model implementations. Introduced a single routine
called from main to register the custom types with Qt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5453 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This merge brings the WSPR feature development into the main line
ready for release in a future v1.6 release.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5424 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Short cut keys implemented via a special key press event handler do
not fully integrate with the UI and standard UI implementation
guidelines, also they introduce an alternative code path that can
diverge from the intended behaviour.
Short cuts to set the next Tx message have been added as
Ctrl+<number>. Alt+<number> short cuts now do as the help implies
i.e. change the current Tx message even if there is another message
being transmitted.
The log QSO window should only be triggered by a 73 Tx message when
transmitting.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4992 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The change to use QTextEdit in read only mode cause the cursor to
become an I-beam type, this changes it to the arrow pointer type that
the previous QTextBrowser used by default.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4959 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Colours behave like other configuration items and changes are only
applied when the Settings UI is dismissed via the "OK" button.
Simplified font settings and use style sheets consistently to set the
application and decoded text fonts. This is necessary because any UI
widget that has a style sheet applied does not honor a font set by
QWidget::setFont() even if there is no font setting in the style
sheet, this is broken behaviour IMHO but that is the way Qt currently
works.
Use a style sheet to style the frequency display and clock. This is
necessary to allow fonts to be cascaded through parent style sheets
and still be overridden on these widgets.
Simplify the decoded text widgets, there is no need to use the
QTextBrowser as a super class since the simpler QTextEdit set as
read-only is sufficient. Also removed colour setting via a background
brush as it doesn't work and the HTML 'bgcolor' attribute works
correctly.
Change to UI properties of the decoded text widgets to allow
horizontal scrolling if required, this allows larger fonts to be used
without truncating decoded messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4957 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Since the log files have moved to a hidden directory a menu action to
open the logs directory in a suitable system applicaiton is needed.
Added "Open log directory" to File manu bar pop up menu.
Merged from wsjtx-1.4 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4471 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
So that a manual can be viewed without an Internet connection a second
manual action has been added to the WSJT_X help menu. This shells out
to the default web browser with a local file target.
The build has been enhanced to install and package the current version
of the HTML user manual as downloaded from the project web site at
build time
The package file locations have been adjusted to be compatible with
the QStandardPaths class so that its locate() method can be used to
portably access resources like this local help file
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4359 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
to minimum in several places so that window contents extend to the
edges and widgets are packed more tightly. Arguably this makes
better use of available screen space.
Comments will be appreciated! If people don't like these changes,
they can be reverted.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4138 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The macro edit page in the settings dialog now allows multiple items
to be selected in an extended selection.
The macro items can be rearranged by drag and drop of single items or
whole selections.
The delete button and context menu item will now delete all the
selected items.
The free text macro drop down combo boxes on the main screen now
automatically insert new macros into the macros list (at the end) if
the ENTER key is pressed while the combobox has focus.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4038 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
default).
Reorganized Modulator interface so that it can control the stream
it writes to.
Make sure only QAudioOutput::stop is called at the end of sending
rather than QAudioOutput::reset which discards pending samples.
Added a quick close option to the Modulator::stop slot to discard
pending buffers if required.
Fix issue in CW synthesizer that was causing CW to be inverted
occasionally.
Made global arrays of symbols volatile because compiler waa
optimizing away reads in sound thread. These global variables
must go eventually as they are a multi-threading hazard.
Simplified TX sequencing to remove some duplicate signals.
Increased range of TX attenuator from 10dB to 30dB. This is mainly for
non-Windows platforms where the attenuator isn't linearized correctly.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3985 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This allows writable files to be located in the "correct"
location for each platform rather than in the directory of
the executable which, in general, is not recommended or
allowed in some cases.
A preprocessor macro WSJT_STANDARD_FILE_LOCATIONS is used to
switch be tween old and new functionality, currently it is on
by default. It can be turned off by defining it to a false
value (0) or more simply with cmake-gui setting the option
with the same name. JTAlert can only work with the old
non-standard file locations until Laurie VK3AMA chooses to
support the new file locations.
Even if the above is not enabled; the QSettings file is
written to a user specific location so it will be shared by
all instances of the program (i.e. across upgrades). See
below for multiple concurrent instance support changes.
Added a command line parser module for Fortran.
Added 'lib/options.f90' to facilitate more complex argument
passing to jt9 to cover explicit file locations.
Changed the way multiple concurrent instances are handled.
This is to allow the program to be run multiple times from
the same installation directory.
A new wsjtx command line optional argument is available "-r"
or "--rig" which enables multiple concurrent instance
support. The parameter of the new option is a unique name
signifying a rig or equivalent. The name is used as the
shared memory segment key and in window titles. The name is
also used to access unique settings files and writable data
files like ALL.TXT and log files. No attempt has been made
to share these files between concurrent instances.
If "-r" or "--rig" is used without a parameter it still
enables multiple concurrent instance support for that
instance. All instances must use a unique parameter, one of
which may be empty.
The rig name is appended the
QCoreApplication::applicationName() for convenient usage like
window titles.
Set non Qt locale to "C".
This ensures that C library functions give consistent results
whatever the system locale is set to. QApplication follows
the system locale as before. Thus using QApplication and its
descendants like widgets and QString for all user visible
formating will give correct l10n and using C/C++ library will
give consistent formatting across locales.
Added top level C++ exception handling to main.cpp.
Because the new transceiver framework uses exceptions
internally, the main function now handles any exceptions that
aren't caught.
Retired devsetup, replaced with Configuration.
Configuration is a class that encapsulates most of the
configuration behavior. Because rig configuration is so
closely coupled with rig operation, Configuration serves as a
proxy for access to the rig control functions. See
Configuration.hpp for more details of the Configuration
interface.
Menu changes.
Various checkable menu actions moved from main menu to the
Configuration dialog. The whole settings menu has been
retired with the single "Settings..." action moved to the
file menu for consistency on Mac where it appears as
"Preferences" in line with Mac guidelines.
New data models for data used by the application.
ADIF amateur band parameters, free text message macros, spot
working frequencies and, station information (station
descriptions and transverter offsets per band) each implement
the QAbstractItemModel interface allowing them to be used
directly with Qt view widgets (Bands.hpp, FrequencyList.hpp
and, StationList.hpp). Configuration manages maintenance of
an instance of all but the former of the above models. The
ADIF band model is owned by Configuration but requires no
user maintenance as it is immutable.
Band combo box gets more functionality.
This widget is now an editable QComboBox with some extra
input capabilities.
The popup list is still the list of spot working frequencies,
now showing the actual frequency decorated with the band
name. This allows multiple spot frequencies on a band if
required.
The line edit allows direct frequency entry in mega-Hertz
with a completer built in to suggest the available spot
working frequencies. It also allows band name entry where
the first available spot working frequency is selected.
Recognized band names are those that are defined by the ADIF
specification and can be found in in the implementation of
the ADIF bands model (Bands.cpp).
If an out of band frequency is chosen, the line edit shows a
warning red background and the text "OOB". Out of band is
only defined by the ADIF band limits which in general are
wider than any entities regulations.
Qt 5.2 now supports default audio i/p and o/p devices.
These devices are placeholders for whatever the user defines
as the default device. Because of this they need special
treatment as the actual device used is chosen at open time
behind the scenes.
Close-down behavior is simplified.
The close-down semantics were broken such that some objects
were not being shut down cleanly, this required amendments to
facilitate correct close down of threads.
User font selection added to Configuration UI.
Buttons to set the application font and the font for the band
and Rx frequency activity widgets have been added to the
Configuration UI to replace the file based font size control.
Free text macros now selected directly.
The free text line edit widgets are now editable combo boxes
that have the current free text macro definitions as their
popup list. The old context menu to do this has been
retired.
Astronomical data window dynamically formatted and has font a chooser.
This window is now autonomous, has its own font chooser and,
dynamically resizes to cover the contents.
Double click to Tx enabled now has its own widget in the status bar.
QDir used for portable path and file name handling throughout.
The "Monitor", "Decode", "Enable Tx" and, "Tune" buttons are now
checkable.
Being checkable allows these buttons control their own state
and rendering.
Calls to PSK Reporter interface simplified.
In mainwindow.cpp the calls to this interface are
rationalized to just 3 locations.
Manipulation of ALL.TXT simplified.
Moved, where possible, to common functions.
Elevated frequency types to be Qt types.
Frequency and FrequencyDelta defined as Qt types in their
meta-type system (Radio.hpp). They are integral types for
maximum accuracy.
Re-factored rig control calls in mainwindow.cpp.
The new Configuration proxy access to rig control required
many changes (mostly simplifications) to the MainWindow rig
control code. Some common code has been gathered in member
functions like qsy(), monitor(), band_changed() and
auto_tx_mode().
Rig control enhancements.
The rig control for clients interface is declared as an
abstract interface (See Transceiver.hpp). Concrete
implementations of this interface are provided for the Hamlib
rig control library, DX Lab Suite Commander via a TCP/IP
command channel, Ham Radio Deluxe also via a TCP/IP command
channel and, OmniRig via its Windows COM server interface.
Concrete Transceiver implementations are expected to be moved
to a separate thread after construction since many operations
are blocking and not suitable for running in a GUI thread.
To facilitate this all instantiation of concrete Transceiver
instances are handled by Configuration using a factory class
(TransceiverFactory) for configuration parameter based
instantiation.
Various common functionality shared by different rig
interface implementations are factored out into helper base
classes that implement or delegate parts of the Transceiver
interface. They are TransceiverBase which caches state to
minimize expensive rig commands, it also maps the Transceiver
interface into a more convenient form for implementation
(template methods). PollingTransceiver that provides a state
polling mechanism that only reports actual changes.
EmulateSplitTransceiver that provides split operation by
QSYing on PTT state changes.
EmulateSplitTransceiver can be used with any implementation
as it follows the GoF Decorator pattern and can wrap any
Transceiver implementation.
OmniRigTransceiver is derived directly from TransceiverBase
since it doesn't require polling due to its asynchronous
nature. OmniRigTransceiver is only built on Windows as it is
a COM server client. To build it you must first install the
OmniRig client on the development machine
(http://www.dxatlas.com/omnirig/).
DXLabSuiteCommanderTransceiver derives from
PollingTransceiver since it is a synchronous communications
channel. No third party library is required for this
interface.
HRDTransceiver also derives from PollingTransceiver. The HRD
interface library has been reverse engineered to provide
functionality with all available versions of HRD. No third
party libraries are required.
HamlibTransceiver likewise derives from PollingTransceiver
since the Hamlib asynchronous interface is non-functional.
Although this class will interface with the release version
of Hamlib (1.2.15.3); for correct operation on most rigs it
needs to run with the latest master branch code of Hamlib.
During development many changes to Hamlib have been submitted
and accepted, hence this requirement. Hamlib source can be
obtained from git://git.code.sf.net/p/hamlib/code and at the
time of writing he master branch was at SHA 6e4432.
The Hamlib interface directly calls the "C" interface and the
modified rigclass.{h,cpp} files have been retired.
There is a rig type selection of "None" which may be used for
non-CAT rigs, this is actually a connection to the dummy
Hamlib device.
PollingTransvceiver derives from TransceiverBase and
TransceiverBase derives from the Transceiver interface.
Each interface implementation offers some possibility of PTT
control via a different serial port than the CAT port. We
also support PTT control directly via a second serial port.
This is done by delegating to a dummy Hamlib instance which
is only used for PTT control. This means that
DXLabSuiteCommanderTransceiver, HRDTransceiver and
OmniRigTransceiver always wrap a dummy HamlibTransceiver
instance. The factory class TransceiverFactory manages all
these constructional complexities.
Serial port selection combo boxes are now editable with a
manually entered value being saved to the settings file.
This allows a non-standard port device to be used without
having to edit the settings file manually.
For TCP/IP network CAT interfaces; the network address and
port may be specified allowing the target device to be
located on a different machine from the one running wsjtx if
required. The default used when the address field is left
blank is the correct one for normal usage on the local host.
Selecting a polling interval of zero is no longer possible,
this is because the rig control capability can no longer
support one way connection. This is in line with most other
CAT control software.
In the Configuration dialog there are options to select split
mode control by the software and mode control by the
software. For the former "None", "Rig" and "Fake it" are
available, for the latter "None", "USB" and, "Data" are
available. Because tone generation is implicitly linked to
split mode operation; it is no longer possible to have the
software in split mode and the rig not or vice versa. This
may mean some rigs cannot be used in split mode and therefore
not in dual JT65+JT9 until issues with CAT control with that
rig are resolved. Single mode with VOX keying and no CAT
control are still possible so even the most basic transceiver
setup is supported as before.
Configuration now supports a frequency offset suitable for
transverter operation. The station details model
(StationList.hpp) includes a column to store an offset for
each band if required.
CMake build script improvements.
The CMakeLists.txt from the 'lib' directory has been retired
with its contents merged into the top level CMakeLists.txt.
Install target support has been greatly improved with the
Release build configuration now building a fully standalone
installation on Mac and Windows. The Debug configuration
still builds an installation that has environment
dependencies for external libraries, which is desirable for
testing and debugging.
Package target support is largely complete for Mac, Windows
and, Linux, it should be possible to build release installers
directly from CMake/CPack.
Cmake FindXXXX.cmake modules have been added to improve the
location of fftw-3 and Hamlib packages.
Version numbers are now stored in Versions.cmake and work in
concert with automatic svn revision lookup during build. The
version string becomes 'rlocal'± if there are any uncommitted
changes in the build source tree.
Moved resource like files to Qt resources.
Because location of resource files (when they cannot go into
the installation directory because of packaging rules) is
hard to standardize. I have used the Qt resource system for
all ancillary data files. Some like kvasd.dat are dumped out
to the temp (working directory) because they are accessed by
an external program, others like the audio samples are copied
out so they appear in the data directory under the default
save directory.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3929 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Note to developers: Not sure about the makefiles...
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3835 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Change "Appendix x" section headings to useful descriptions.
3. Add KB1ZMX and W4TI to the WSJT-X "About" screen and Acknowledgments
in the User's Guide. (Hope I didn't forget anyone -- please advise
if I did!)
4. A few more minor tweaks to User's Guide
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3672 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
bad data.
2. Fix a bug that could allow a Koetter-Vardy false decode instead of
a valid Berlekamp-Massey decode, sometimes leading to program crash.
3. Many more edits in the User's Guide, *.adoc files.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3664 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
