Dont allow SplitTx operation with Ham Radio Deluxe.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3478 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
(JT9 will typically be about 2 kHz higher.)
2. Add a few default Tx macros, as examples.
3. Fix display of correct UTC on decoded lines, when "Shift+D" is used to
do another wideband decode during the next Rx sequence.
4. Clear the "Split Tx" checkbox when CAT is not enabled (but remember
what its state should be, if CAT is re-enabled).
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3468 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Use ptt_() function included in getfile.cpp.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3465 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Correct the TxMode label on program startup.
2. Insert TxMode (not RxMode) into the "Transmitting..." lines in ALL.TXT.
3. Put TxMode in wsjtx_status.txt.
4. F4 clears Az, Dist, and all Tx messages as well as DxCall and DxGrid.
5. Make it possible to decode JT9 in the "JT65 region", and vice-versa, with
directed double-click on signal in waterfall.
6. Improved logic for enabling/disabling TestPTT button on setup screen.
7. Do not call getFreq() when TestPTT is activated under CAT control.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3463 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Please note: features added today need more testing that I have yet given
them!
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3345 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Added option to retain between QSOs the Comments field for ADIF and
wsjtx logs.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3343 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
If paOutDevice was not a saved setting, use Pa_GetDefaultOutputDevice().
This allows wsjtx to startup with default audio on a new install.
However, it does not set the menu index numbers, so the Config SoundIn/Out
menus do not look correct, until they have been set and saved once.
It would be better if only the device names were saved in settings,
because the index numbers can change, especially if USB soundcards
are added or removed.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3339 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Double-click on a 73 message sets Tx5, rather than Tx6.
3. Clean up a few remaining compiler warnings.
4. Clean up Tab order.
5. Updates to User's Guide
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3320 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
platforms.
2. This might be temporary: set Audio output on unix platforms to stereo,
i.e., channels=2. On my Ubuntu system, at least, this makes it play
correctly on all of the relevant audio devices in the list, including
hardware and virtual (".asoundrc-implemented") devices.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3317 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Removed all vestiges of NB code and controls.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3314 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. SoundOut buffer size can be set by editing wsjtx.ini.
3. Fixed bug in placement of #ifdef in rigclass.cpp
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3313 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Disable attempted control of T/R switching via HRD: it does not work,
as coded.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3311 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The present code is still OK in Qt 4.x. For Qt5, must replace
#include <QtGui> by #include <QtWidgets> in several places, and
uncomment these lines
//#include <QtConcurrent/QtConcurrentMap>
//#include <QtConcurrent/QtConcurrentRun>
in mainwindow.cpp. More work still to do, for Qt5!
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3309 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Fix two more g95 compiler warnings.
3. Remove some unused code in getfile.cpp.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3305 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
jt9a.F90 in order to suppress a compiler warning.
2. Updated Makefile.linux.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3300 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
*** Beware: some code in this revision will surely fail in Linux! ***
*** Some "#ifdef Win32" statements are still to be included. ***
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3289 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
memory region smaller by some 150 MB.)
2. Some code cleanup (removing unused lstrong, etc.)...
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3283 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Re-establish the pxdb measurement for Thermo.
3. Double-click on decoded line copies it to QSO window (unless it's
already there).
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3276 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This commit will serve as a benchmark for comparison with new code to
be written.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3266 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Fix annoying bug when trying to open rig using a non-existent or
busy serial port.
3. Add acknowledgments to AE4JY
4. Tentative tweaks to "Tab 2" GUI layout.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3261 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
do a rig->Close() if user has done "Test CAT Control" and then hit "Cancel".
2. Remove the "0%" part of Rx noise label; exchange positions of "Rx
Noise" and "QSO Freq" on Status Bar.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3260 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Delete the last tentatively-saved file on program exit.
No negative numbers needed on "CW ID" spinner.
Updates to User's Guide.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3259 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
is now a button. It is enabled only when Orange, which means CAT
control is essentially Program to Radio only. Clicking the button
causes a one-time read of the radio's dial frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3256 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
screen.
2. Some copy-editing on the User's Guide.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3255 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Add jt9code.exe to the Windows installation file.
3. Changed hotkey for "Special Mouse Commands" to F5, so that F4 again works
as it did.
4. Several corrections to shortcuts.txt.
5. Added section "Under the Hood" to the User's Guide.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3254 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
UPdate Makefile.MinGW.
Much work new on User's Guide.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3251 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
I have changed the declarations of the Rig class functions we use:
open()
setConf()
getFreq()
setFreq()
setPTT()
close()
... so that each one returns the (negative) error code returned by
hamlib. These functions no longer throw exceptions.
Initial tests seem to show things working well. I have found one
condition that causes a crash. The rig is initially opened and is
running OK (in this case, with the Polling interval set to 1 s). Then
the radio is turned off. The next call to getFreq() never returns.
Probably we need to set a timeout limit?
The code is kinda on the quick-and-dirty side. Improvements will be
welcom!
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3246 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Joe Taylor
John T Nogatch
Edson W. R. Pereira