__ __ ______ _____ ________ __ __ | \ _ | \ / \ | \| \ | \ | \ | $$ / \ | $$| $$$$$$\ \$$$$$ \$$$$$$$$ | $$ | $$ | $$/ $\| $$| $$___\$$ | $$ | $$ ______ \$$\/ $$ | $$ $$$\ $$ \$$ \ __ | $$ | $$| \ >$$ $$ | $$ $$\$$\$$ _\$$$$$$\| \ | $$ | $$ \$$$$$$/ $$$$\ | $$$$ \$$$$| \__| $$| $$__| $$ | $$ | $$ \$$\ | $$$ \$$$ \$$ $$ \$$ $$ | $$ | $$ | $$ \$$ \$$ \$$$$$$ \$$$$$$ \$$ \$$ \$$ Copyright 2001 - 2021 by Joe Taylor, K1JT. Release: WSJT-X 2.5.2 Oct 29, 2021 ---------------------- This is mostly a bug fix release. It has the following changes since release 2.5.1: - Repair a longstanding regression that caused signal reports from tail-ended Tx2 messages to be omitted from logged information - Repair a regression associated with setting the main window width on program startup. - Repair a problem with Q65 decodes of type 'q3' for messages of the form " Call_2" - Implement Q65 decodes of type 'q3' for the message "TNX 73 GL". - Execute code associated with Q65 decodes of type 'q5' only when the Max Drift control is set to 50. This fix prevents double-incrementing of the message averaging counter on the first decoding sequence. - Polarization offset 'Dpol' from the astronomical data window is now written to file azel.dat if environment variable WSJT_AZEL_EXTRA_LINES has been defined as 1 or greater. Dpol is especially useful for EME on the higher microwave bands. - The Auto Log QSO option in "Settings->Reporting" now behaves the same as the Prompt to log QSO option when not in a special operating context mode. - New hamlib code to correct minor flaws in controlling several rigs. - Update the Chinese and Hong Kong translations of the user interface. - Note that since the WSJT-X v2.5.0 GA release we have not been providing pre-built 32-bit packages for Linux on Intel CPUs, this is due to the mainstream Linux Desktop distributions no longer providing updates for 32-bit only systems. 32-bit WSJT-X can still be built for Linux Intel and is supported at least until some prerequisite package is no longer available. Release: WSJT-X 2.5.1 Oct 21, 2021 ---------------------- This release mainly contains improvements and defect repairs related to Q65 and JT65 modes when used with non-standard and compound calls. Also included is a new feature for microwave aircraft scatter and repairs for defects detected since the 2.5.0 GA release. - Improved Q65 support for 10GHz Aircraft Scatter contributed by Rex, VK7MO, and Roger, W3SZ. (See "10 GHz Terrestrial with Q65" in DUBUS Vol 1/2021 page 64.) Decodes of type 'q3' may now include corrections for frequency drift. - Repair a defect that failed to pre-load the DE and DX calls to the hash lookup tables in the Q65 decoder. - Repair standard message Tx4 and Tx5 generation in Q65 mode when using a non-standard call. - Repair a defect in generation of the standard Tx2 JT65 message in EME mode when using a compound call. - Repair a defect when decoding 77-bit type 4 non-standard call message. - Repair a defect that could cause a crash when switching from Q65 to JT65 mode and attempting a double-click decode. - Enable 'q3' AP decoding in Q65 mode for messages containing a non-standard call. - Repair a defect that required a blank DX Grid to achieve Q65 'q3' decodes of messages containing a non-standard call. - Repair the logic that sets parameters for Q65 "Deep" decoding. - In Q65 mode, allow 'q2' decodes when MyCall is compound or non-standard. - Repair a long-standing defect that could cause a crash when reference spectrum correction is enabled. - Updated UI translations from Xavi, EA3W, Oba-san, JA7UDE, and a new translation for Traditional Chinese by Steven, BU2EL. - Updated CTY.DAT database, tnx to Jim AD1C - Improved main window layout to ensure TxN messages are fully visible. Release: WSJT-X 2.5.0 Sept 27, 2021 ------------------------- WSJT-X in this release is nearly identical to that in WSJT-X 2.4.0. The Q65 decoder has been enhanced to measure and compensate for linear frequency drift in Q65 signals. In addition, the Windows installation package now includes version 3.0 of application MAP65 which has Q65 support to match and improve on its existing JT65 capabilities. See the 2.5.0 release candidate notices below for a summaries of the other changes included in this release. WSJT-X 2.5.0 is bundled with Hamlib version 4.3.1 which includes important regression repairs over the earlier 4.3 release. Other changes in the package since WSJT-X 2.5.0-rc6 include the following enhancements and defect repairs: MAP65: - Ensure that CALL3.TXT is not deleted while updating the file (this allows sharing using symlinks to work). - Fix MAP65's generation of Tx3 message for abs(SNR)< 10. WSJTX: - Repair a defect that caused CAT errors when using WSPR band hopping and auto tune-up with some Icom rigs. - Ensure that CALL3.TXT is not deleted while updating the file (this allows sharing using symlinks to work). Release: WSJT-X 2.5.0-rc6 Sept 6, 2021 ------------------------- Remember that the WSJT-X 2.5.0 package includes MAP65 3.0.0. Changes in the package since WSJT-X 2.5.0-rc5 include the following enhancements and defect repairs: MAP65: - There are no functional changes to MAP65 in this release. WSJT-X: - Repair a file handle leak in wsprd (tnx Phil, KA9Q). - Better handling of the Tx1 buttons when changing special operating modes. - Q65 mode now supports contest special operating modes. - Repair an issue when non-ASCII characters used in account names. - Repair a regression that prevented WSPR band-hopping working when the Tx percentage is zero. Release: WSJT-X 2.5.0-rc5 Aug 5, 2021 ------------------------- Remember that the WSJT-X 2.5.0 package includes MAP65 3.0.0. Changes in the package since WSJT-X 2.5.0-rc4 include the following enhancements and defect repairs: MAP65: - When you double-click on lower waterfall, Ftol is set to 100 only if it is currently set to a higher value. - Early decoding pass is skipped when data are read from disk. - Duplicate decodes are suppressed only when at the same frequency. WSJT-X: - Repair a regression that caused some messages involving compound or nonstandard callsigns to be encoded as free text Release: WSJT-X 2.5.0-rc4 Aug 1, 2021 ------------------------- Remember that the WSJT-X 2.5.0 package includes MAP65 3.0.0. Changes in the package since WSJT-X 2.5.0-rc3 include the following enhancements and defect repairs: MAP65: - Suppress display of duplicate decodes - Increase the length of .tf2 & .iq files to 56 s - Implement an early decoding pass at 52 s - Clean up the output written to map65_rx.log WSJT-X: - Repair a defect in CALL3.TXT lookups that incorrectly matched partial calls - Instructions in macOS ReadMe.txt to suppress App Nap energy saving - Revised User Guide using FT8 mode for the basic tutorial - Allow contest and FD operating in Q65 mode Release: WSJT-X 2.5.0-rc3 Jul 5, 2021 ------------------------- Remember that the WSJT-X 2.5.0 package includes MAP65 3.0.0. Changes in the package since WSJT-X 2.5.0-rc2 include the following enhancements and defect repairs: MAP65: - Correct two defects that could cause "hung decoder" status - Translate reported frequencies so that |DF| <= 500 Hz for Q65 decodes. - Provide access to Release Notes from the Help menu - Correct the formatting of Q65 messages to livecq - Repair an Xpol polarization finding hang - Build MAP65 to start without an attached console WSJT-X: - Repair a long standing defect that caused UDP Protocol Heartbeat messages to not be sent when no other intervening messages are sent. Release: WSJT-X 2.5.0-rc2 Jun 28, 2021 ------------------------- Remember that the WSJT-X 2.5.0 package includes MAP65 3.0.0. Changes in the package since WSJT-X 2.5.0-rc1 include the following enhancements and defect repairs: MAP65: - Compute polarization angle for Xpol systems and display to nearest degree - Compute and display the recommended Tx polarization - Protect against Fortran bounds errors in several places - Insert leading 0 when needed in UTC hours and minutes on waterfall - Wideband Q65 synchronization corrected to include single-polarization mode - Corrected a one-symbol (0.6 s) delay in Q65 Tx audio - Basic instruction document for building an MS Windows portaudio DLL for MAP65 users who are unable to use WDM/KS drivers for their multi-channel sound cards. WSJT-X (including the decoder for Q65 used by MAP65): - Increase maximum DT to 5.5 s when EME decoding is enabled in Q65 - Fix generation of Tx5 message when "hiscall" has suffix /P or /R. - Improve width management of GUI's band-selection combo box - Restore plotting of Q65 sync curve after a q3 decode - Disable selection of "View | Message Averaging F7" for modes other than JT4 and JT65 - Switching to Q65 mode now defaults to "Decode | Fast" - Repair a long standing regression with message generation for 72-bit modes when using a compound callsign. - Repair a defect in diagnostic logging that could cause crashes on some platforms. - Repair a defect which failed to strip leading and trailing spaces on input of callsigns during validation. - Hamlib updates including repair of defects with PTT handling on a separate serial port via rigctld, delayed PTT with Elecraft K3 series rigs, and support for the Icom IC-575 rig. - Updated CTY.DAT database Release: WSJT-X 2.5.0-rc1 Jun 3, 2021 ------------------------- WSJT-X in this release is nearly identical to that in WSJT-X 2.4.0. The Q65 decoder has been enhanced to measure and compensate for linear frequency drift in Q65 signals. In addition, the Windows installation package now includes version 3.0 of application MAP65 which has Q65 support to match and improve on its existing JT65 capabilities. The following notable defect and regression repairs are included: - FST4W mode no longer saves .WAV files when "Menu->Save->None" is checked. Release: WSJT-X 2.4.0 May 24, 2021 --------------------- WSJT-X 2.4.0 General Availability Release adds new Q65 mode functionality and decoder optimizations and repairs several defects and regressions discovered in the RC4 and v2.3.1 GA releases. Since the release candidates documented below this final release includes the following enhancements and defect repairs. - On MS Windows WSJT-X now ships with a DLL version of the Hamlib library, specifically Hamlib version 4.2. This should allow Hamlib bug fixes to resolved by the user replacing the DLL with an updated version. - Repair a defect with own call decode highlighting when callsigns with a common root are decoded. - Q65 message averaging correctly disabled as be menu option. - Repair a regression with missing timestamps in AlL.TXT for the MSK144 mode. - Repair a defect in the selection of working frequencies matching the current band and mode combination. - WSPR band hopping mode now generates a tune up tone for bands where it is scheduled to transmit. - Repair a long standing defect per band tune and Tx power level memories. - More flexibility for inputting calls into the DX Call field, leading and trailing white space characters are allowed but ignored. Release: WSJT-X 2.4.0-rc4 Mar 26, 2021 ------------------------- WSJT-X 2.4.0 Release Candidate 4 adds new Q65 mode functionality and decoder optimizations and repairs several defects and regressions discovered in the RC3 and v2.3.0 GA releases. - Correct a problem with display of Q65 sync curves for submodes Q65-120x and Q65-300x. - Audio frequency and decoded message are now saved for up to 100 most recent Q65 decodes. Subsequent double-click on waterfall will search the list for the clicked frequency +/- 10 Hz, recover "DXCall" from the mosr recent decode there, and attempt a decode at that frequency with full "q3" sensitivity. - Use new ADIF recommendations for Q65: mode=MFSK, submode=Q65. - If "Single decode" is unchecked, look for Q65 decodes from accumulated average even after obtaining a single-sequence decode at selected Rx Freq. - For data read from .wav files, display the original UTC (derived from file name) on the waterfall instead of current UTC. - Protect against bounds errors caused by unusual settings on the Wide Graph. - Correct a problem with Split operation in FT4 mode. Thanks to JG1APX. Release: WSJT-X 2.4.0-rc3 Mar 15, 2021 ------------------------- WSJT-X 2.4.0 Release Candidate 3 adds new Q65 mode functionality and decoder optimizations; repairs defects and regressions discovered in the RC2 and v2.3.0 GA releases. - Repaired a memory corruption related to display of Q65_Sync, particularly nasty on macOS. - Q65 now dissplays two sync curves: orange for the current sequence, red for the accumulated average. - Behavior of "Save decoded" has been corrected. - Repaired a defect that caused crash when displaying the Wide Graph with lower frequency limit set to 0. - Program no longer terminates a transmission when Settings is closed. - Program no longer forces TxFreq to 700 or 1000 Hz when entering Q65 mode or closing Settings. Instead, it highlights TxFreq with red background when its value should be 700 Hz but is not. - Program displays a warning label if a contest mode is active in Q65 mode. - Many updates to User Guide, mostly related to Q65. - Repaired a regression that disallowed a new QSO initiation after an abandoned QSO. Release: WSJT-X 2.4.0-rc2 Mar 6, 2021 ------------------------- WSJT-X 2.4.0 Release Candidate 2 adds new Q65 mode functionality and decoder optimizations; repairs defects and regressions discovered in the RC1 release. - Q65 sample .WAV files added. - Repair a defect that caused WSJT-X to crash when launched from an icon on macOS. - Repair a crash when using the JT4 mode. - Sequencing improvements to hold transmitted signal report fixed during a QSO. - UI translation updates tnx to Sze-to, VR2UPU, and Michael, 5P1KZX. - Enable the "Call 1st" option for Q65. - Improved Q65 message averaging that linearly averages the first 4 sequences and averages exponentially thereafter using a time-constant of 4 sequences. - Improved macOS post-install instructions, tnx to John, G4KLA. - Enhanced Q65 simulator that generates file names compatible with message averaging, tnx Charlie, G3WDG. - Q65 simulator option to generate single tone waveforms, tnx to Charlie, G3WDG. - Better suppression of birdies in the Q65 decoder. - Blank Q65 decode messages removed. - Automatic low Tx audio offset for the widest Q65 modes to keep Tx signal in transmitter passband, tnx to Charlie, G3WDG. - Improved SNR estimates for Q65 mode. - Decode depths Fast/Normal/Deep are now identical in Q65 mode. - "Save decoded" is now enabled for Q65 mode. - The obsolete ISCAT mode has been removed. Release: WSJT-X 2.3.1 Mar 26, 2021 --------------------- WSJT-X 2.3.1 General Availability release updates the User Guide to cover the new modes FST4 and FST4W along with sample .WAV files and decoding tutorials. This release also repairs a number of defects and regressions discovered since the v2.3.0 release, including those below. - When sending traffic to a multicast UDP server ensure that the local loop-back interface is used if no others are selected. - Repair a defect in instance lock file handling that causes an infinite loop on start up. - Invert the PTT serial port sharing default behaviour, and enable sharing when non-Hamlib CAT control is combined with direct serial port PTT control. - Allow the FST4 and FST4W decoders to continue after the first successful decode when using negative NB values to try multiple NB values. - Repair defects in auto-sequencing, particularly with responding to a repeated final message. In general a double-click of the repeated message now does the right thing. - Repair a regression that had inadvertently disabled EU VHF Contest mode when using the MSK144 mode. - Repair a defect that could caused incorrect log entry fields when using FT4 mode and a priori (AP) decoding. - Repair defects saving .WAV files for periods with decodes. - Offer a new scheme for adjusting macOS shared memory parameters. Release: WSJT-X 2.4.0-rc1 Feb 3, 2021 ------------------------- WSJT-X 2.4.0 is a program upgrade offering a new mode called Q65. It builds on the capabilities of the QRA64 mode to offer a flexible large symbol alphabet, low code rate, mode with excellent characteristics when used for EME on VHF through to microwave bands, and with challenging weak signal propagation via iono-scatter and similar on VHF bands. The Q65 mode carries the same 77-bit message payload as the popular FT8, MSK144, FT4, and FST4 QSO modes. Q65 also offers a range of T/R periods (15 second through to 5 mins) and tone spacings (up to 32 times the base spacing) suitable for adapting to required sensitivity and various channel frequency spreading characteristics. The Wide Graph plotter has a super-sensitive synchronization spectrum capable of detecting signals below visibility on the waterfall plot. The new synchronization plot combined with comprehensive a priori (AP) decoding techniques and message summing and averaging over multiple Rx periods should make use near the limits of extreme weak signal operating better than prior modes in all appropriate situations. Release: WSJT-X 2.3.0 Feb 2, 2021 --------------------- WSJT-X 2.3.0 General Availability release adds the new modes FST4 and FST4W along with many defect repairs. See summaries below and for the prior release candidates (2.3.0-rc1 through -rc4) of this version for details. - FST4/W: Disable envelope shaping at start and end of transmission when environment variable FST4_NOSHAPING=1. Works for fst4sim too. - Add time stamp to error message boxes to aid diagnosis. - Repair a defect that caused crashes at start up for some macOS Big Sur users. - Repair a defect that could cause the jt9 slow mode decoder process to exit incorrectly with a failure status. - Updated CTY.DAT file. Release: WSJT-X 2.3.0-rc4 Jan 26, 2021 ------------------------- WSJT-X 2.3.0 Release Candidate 4 is a stop-gap release while some recent important Hamlib changes are being verified. Also included are the following regression and defect repairs. - The wsprd command line tool uses the current working directory for the data file directory if it is not specified. - Updates to the language translations of the WSJT-X user Interface. Release: WSJT-X 2.3.0-rc3 Jan 6, 2021 ------------------------- WSJT-X 2.3.0 Release Candidate 3 adds an improved FST4W decoder and fixes several defects and regressions discovered since the second release candidate. - FST4W: Improve FST4W decoder sensitivity on fading channels and decrease false decode rate. FST4W uses 50-bit messages and a 24-bit CRC. The 74-bit message+CRC is encoded into a 240-bit codeword. Received messages are decoded by two different decoders: (i) a “belief propagation” (BP) decoder and (ii) an ordered statistics decoder (OSD). The ordered statistics decoder has a knob that allows any or all CRC bits to be treated as additional parity bits rather than as part of the message+CRC field. Thus, the OSD decoder can decode the received message as a (240,50+Nc) code, where Nc is any integer between 0 and 24. In the RC1 and RC2 releases the OSD decoding attempt treated the code as a (240,64) code (14-bit CRC). This release uses 2 OSD decoding attempts that treat the received word as (i) a (240,66) code with 16-bit CRC and code rate 0.308 and (ii) a (240,50) code with no CRC and code rate 0.208. Codewords returned by the (240,50) CRC-less decoding attempt are unpacked and the decode is printed only if it contains a callsign/grid pair that have been previously decoded by the belief propagation decoder (which treats the code as a (240,74) code with 24-bit CRC) or the ordered statistics decoder configured for (240,66) (16-bit CRC). The callsign/grid memory is stored in file “fst4w_calls.txt” which resides in the data directory. - FT8: Fixed a crash triggered by double clicking on the waterfall to invoke a decode of a signal in the preceding T/R interval. - FST4W: Do not save .c2 files. - FST4W: Correct a bug that could cause incorrect operation when using negative noise blanker (NB) percentage to trigger looping over a range of NB percentages. - fst4sim: Added simulation of Lorentzian fading spectrum, invoked by negative fspread values. - Color highlighting scheme window fixed in dark mode. - Reports sent by QSO partners to other stations no longer logged in error. - UDP Status(1) message now includes the current Tx message. - Example diagnostic logging configuration files included. - Use system localization for date fields in Log QSO dialog. - Improvements to audio input and output buffer sizes. - wsprd: Fails gracefully if data directory does not exist. - wsjtx_app_version: new utility to print application version string. - Regression causing incorrect working frequency selection when changing modes repaired. - Regression with QSO initiation with "Best S&P" repaired. - Updated installation instructions for macOS covering M1 hardware. - Improved compatibility is Debian 9 required distribution packages. - Repair regression with missing time-stamps in the ALL.TXT journal. - Allow hamlib_settings.json to work with PTT only configurations so that optional PTT sharing on RTS or DTR can be enabled. - Several improvements to main window sizing and layout. - Repair regression with OpenSSL libraries being required when LoTW highlighting is not enabled. - Repair a defect that caused 2 by 1 callsigns to be incorrectly parsed as non-standard. - Several updates to international UI translations. Release: WSJT-X 2.3.0-rc2 Nov 16, 2020 ------------------------- WSJT-X 2.3.0 Release Candidate 2 fixes issues found in RC1 and includes some new functionality that missed the RC1 cut off deadline. - Dropped audio samples message box removed, warnings and errors for these are now sent to the WSJT-X system log. - FST4W spots to WSPRNet.org will be augmented such that the server can distinguish the mode being spotted. Spots to WSPRNet.org will no longer be restricted to WSPR sub-bands. - A new internal system and data logging facility used to provide trace, debug, information, warning, error, and fatal error messages. The verbosity and filtering of messages is user definable via a configuration file. Without a configuration file a basic log is written with information, warning and error messages only. Log files are automatically rotated to limit disk usage. - Due to some users using inappropriate multicast IP addresses for their interoperating severs the default behaviour now is to only send multicast UDP datagrams to the loop-back network interface. Users who require WSJT-X UDP Message Protocol datagrams to reach other hosts will now have to configure WSJT-X to send on an appropriate network interface, and use an appropriately scoped multicast group address for their server applications. If you are not sure then 224.0.0.1 (or ff02::1 if IPv6 is desired) is a safe choice. Release: WSJT-X 2.3.0-rc1 Sept 28, 2020 ------------------------- WSJT-X 2.3.0 is a program upgrade offering two new modes designed especially for use on the LF and MF bands. FST4 is for 2-way QSOs, and FST4W is for WSPR-like transmissions. Both modes offer a range of options for T/R sequence lengths and threshold decoding sensitivities extending well into the -40 dB range. Early tests have shown these modes frequently spanning intercontinental distances on the 2200 m and 630 m bands. Further details and operating hints can be found in the "Quick-Start Guide to FST4 and FST4W", posted on the WSJT web site: https://physics.princeton.edu/pulsar/k1jt/FST4_Quick_Start.pdf WSJT-X 2.3.0-rc1 is a beta-quality release candidate for a program upgrade that provides a number of new features, capabilities, and defect repairs. These include: - New modes FST4 and FST4W targeting LF and MF bands. - Improved noise baseline discovery for more reliable SNR estimates. - On the waterfall and 2D spectrum a tool-tip shows the frequency offset under the mouse pointer. - The *On Dx Echo* Doppler compensation method has been modified in response to feedback from Users. Basic functionality is unchanged. See the User Guide (Section 8.1) for more information. - Improved user_hardware script or program initiation for WSPR band-hopping mode. - Decoded QSO mode message display narrowed to make appended information easier to view without scrolling the window. - Option to record the propagation mode in logged QSO records. - ADIF v3.1.1 compliance. - Option to connect to PSKReporter using TCP/IP for those with very poor Internet connections. - Major rewrite of the PSKReporter interface to improve efficiency and reduce traffic levels. - Removal of the Tab 2 generated messages. - Accessibility improvements to the UI. - Tweaked decode speed options for a better user experience with lower powered single-board computers like the Raspberry Pi. - Updates to UI translations in Spanish, Italian, Catalan, Chinese, Hong Kong Chinese, Danish, and Japanese. - Audio devices only enumerated when starting up and opening the "Settings->Audio" device lists. - Option to select the default audio device removed to minimize the likelihood of system sounds being transmitted. - Better handling of missing audio devices. - Improved and enhanced meta-data saved to .WAV files. - More reliable multi-instance support. - Included CTY.DAT file moved to installation share directory. - The bundled Hamlib library is updated to the latest available which fixes several regressions, defects, and adds new rig support. - Fixed some edge-case message packing and unpacking defects and ambiguities. - Fix a defect that allowed non-CQ messages to be replied to via the UDP Message Protocol. - Fix a long-standing defect with Tx start timing. - Repair a defect with style sheets when switching configurations. - Repair defects that made the astronomical data window an several main window controls unreadable when using the dark style sheet. - Repair a regression with setting WSPR transmitted power levels. - Repair a regression with newly created ADIF log file's header. - Many other defects repaired. Release: WSJT-X 2.2.2 June 22, 2020 --------------------- WSJT-X v2.2.2 is a bug fix release, mainly to incorporate the new RAC section PE into the FT8/FT4/MSK144 Contest Mode for Field Day. - Stations intending to operate in Field Day (FD) are urged to upgrade to this release, without it you cannot set your section to PE, and of equal importance you cannot decode contest messages from stations who are operating from PE without this upgrade. - FT8 decoder speeded up in Normal and Fast modes. This change gives a speed of decoding closer to that of v2.1.2 without compromising the number of decodes. It is particularly targeted for slower single board computer users such as the Raspberry Pi Model 3 or similar. - Thanks to our user interface language translation contributors for many improvements to the translated strings. - The DX Grid field is now cleared automatically when the DX Call field is changed. Care should be taken to complete entry of a callsign before entering a grid square. Release: WSJT-X 2.2.1 June 6, 2020 --------------------- WSJT-X v2.2.1 is a bug fix release that fixes regressions found in the prior v2.2.0 release. Here is a brief summary; - Incorporate a revised Hamlib version the address a regression in rig control of some rigs including the Yaesu FT-991 and FT-891. - Repair a defect in 6 character gridsquare lookup from the CALL3.TXT database, and improve "Lookup" button processing. - Repair a defect with selecting Wide Graph 2D spectrum types in translated UIs. - Repair a regression that blocked the Highlight Callsign UDP request from highlighting terms including a '+' character. - Repair a defect that caused hash code lookups of one's own call to fail after an extended period of inactivity, when operating with a non-standard callsign. - Repair a regression where occasional Highlight Callsign UDP requests with the 'Highlight last' parameter as true highlighted a match in a prior period. This fix include a performance improvement when processing any Highlight Callsign request with 'Highlight last' as true. - Include support for the Yaesu FT-920 when controlled by Ham Radio Deluxe. This change inadvertently missed the v2.2.0 GA release. - Correct a documentation issue with the UDP Message Protocol Status(1) message Special Operations Mode enumeration values ("WW DIGI added", Fox, and Hound renumbered). Thanks to Sam, W2JDB, for raising this issue. - Updated Catalan UI translation, tnx Xavi, EA3W. - Italian UI translation, tnx Marco, PY1ZRJ. - Updated Spanish UI translation, tnx Cédric, EA4AC. Release: WSJT-X 2.2 June 2, 2020 ------------------- WSJT-X 2.2 is a program upgrade that provides a number of new features and capabilities. Here is a brief summary; for further details see the notes for candidate releases 2.2.0-rc1, -rc2, and -rc3, below, and of course the updated WSJT-X 2.2 User Guide. - Significant improvements to the decoders for FT4, FT8, JT4, JT65, and WSPR. - New format for "EU VHF Contest" Tx2 and Tx3 messages When "EU VHF Contest" is selected, the Tx2 and Tx3 messages (those conveying signal report, serial number, and 6-character locator) now use hashcodes for both callsigns. This change is NOT backward compatible with earlier versions of _WSJT-X_, so all users of EU VHF Contest messages should be sure to upgrade to version 2.2.0. - Accessibility Keyboard shortcuts have been added as an aid to accessibility: Alt+R sets Tx4 message to RR73, Ctrl+R sets it to RRR. As an aid for partial color-blindness, the "inverted goal posts" marking Rx frequency on the Wide Graph's frequency scale are now rendered in a darker shade of green. - User Interface Translations have been enabled. Translations are now available for Catalan, Spanish, Japanese, Chinese, and Hong Kong Chinese. Additiional languages will follow, when available. Note that UI translation is automatic, based on your system primary language. If you do not want the WSJT-X UI translated to your local language then start WSJT-X with the '--language=en' command line option: wsjtx --language=en If you wish to contribute by authoring WSJT-X UI translations please join the new discussion group wsjtx-l10n@Groups.io (https://groups.io/g/wsjtx-l10n), where help from other translation authors and coordination with the development team is available. - Minor enhancements and bug fixes "Save None" now writes no .wav files to disk, even temporarily. An explicit entry for "WW Digi Contest" has been added to "Special operating activities" on the "Settings | Advanced" tab. Contest mode FT4 now always uses RR73 for the Tx4 message. The Status bar now displays the number of decodes found in the most recent Rx sequence. The "Highlight Callsign" UDP message has been enhanced to allow clearing of old highlighting for a specified callsign. Please note a recommended restriction on the use of this message in the documentation here: https://tinyurl.com/y85nc3tg - Hamlib - this library which we use for direct rig control has had many defect repairs and enhancements, we thank the contributors to that project for their work. Release: WSJT-X 2.2.0-rc3 May 29, 2020 ------------------------- WSJT-X 2.2.0-rc3 is the third release candidate for WSJT-X 2.2.0. The most important differences from the -rc2 version are the correction of regressions in hamlib code that affected particular radios and PTT keying by means of DTR or RTS on a COM port. In addition, RC3 has the following enhancements and minor bug fixes: - Updates to Catalan translation of the UI (thanks to EA3W) - Spanish translation of the UI (EA3W) - Load language translations only when matching primary language - Minor corrections to User Guide - Increased FT8 sync threshold in "Normal" and "Fast" decoding - Corrected the code that restores the WideGraph, EchoGraph, and FastGraph windows to normal view after they have been minimized. - Don't allow restart with "ISCAT B" mode label unless VHF features are enabled. - Repair regression defect in WSPR power combo box items Release: WSJT-X 2.2.0-rc2 May 25, 2020 ------------------------- WSJT-X 2.2.0-rc2 is a release candidate for WSJT-X 2.2.0. The following bugs present in the -rc1 version have been fixed: - Missing blank line between some decode sequences. - Improper functioning of "Start new period decodes at top". - Font selection caused crash on some macOS systems. - Mouse action in band selector box not right in some macOS systems. - Incorrect recall of Tx power setting in WSPR mode. - Many fixes to hamlib library and executables (rigctld, etc.). - Some regional settings did not allow WSJT-X to start. - Main window "looked like old Windows" in macOS. - Crash when "Ref Spec" is selected and no refspec.dat available. - Improper decoding of some FT4 messages with hashed "MyCall". - Crash after warning message about double-clicking in ISCAT mode. In addition, we have made the following improvements: - Updated some figures and text in User Guide. - Corrected some formatting issues in the pdf version of User Guide. - Added some new sample files. - Improved shape and position of "green goal post" in Wide Graph. - Significantly reduced the rate of false decodes in FT4 and FT8. - Allow FT4 to use NA VHF Contest message formats. - Hold Tx frequency no longer cleared when switching between modes. - Added capability for translations of the user interface into languages other than English. First working example (special thanks to Xavi Perez, EA3W!), is Catalan. Spanish will be next. - Performance improvements to decode highlighting via UDP messages. And finally: Increasing FT8 usage on the popular bands 40, 30, and 20m means that the default 3 kHz sub-bands are often wall-to-wall with signals. Overcrowding encourages some to turn on their amplifiers, which only makes things worse. We are trying to coordinate the suggested frequencies in WSJT-X with updated band plans being considered by IARU, ARRL, and other amateur radio societies. On a trial basis, and in response to numerous suggestions from around the world, we have added a second set of suggested dial frequencies for FT8 on three HF bands and also on 6 meters. The new suggested dial frequencies are 7.071, 10.133, 14.071, and 50.310 MHz. These frequencies will appear in your drop-down band-selector list after you go to the "Settings | Frequencies" tab, right-click on the frequency table, and select "Reset". Alternatively, you can add the new FT8 frequencies manually. When the conventional FT8 sub-band on 6, 20, 30, or 40 m seems too full, please try moving your dial frequency down 3 kHz! Be aware that as currently implemented, WSJT-X will set your dial to the lowest frequency for the selected mode and band, when you switch bands. See the next section for a list of other program improvements since WSJT-X 2.1.2. Release: WSJT-X 2.2.0-rc1 May 10, 2020 ------------------------- WSJT-X 2.2.0-rc1 is a beta-quality release candidate for a program upgrade that provides a number of new features and capabilities. These include: - Improvements to the decoders for five modes: FT4: Corrected bugs that prevented AP decoding and/or multi-pass decoding in some circumstances. The algorithm for AP decoding has been improved and extended. FT8: Decoding is now spread over three intervals. The first starts at t = 11.8 s into an Rx sequence and typically yields around 85% of the possible decodes for the sequence. You therefore see most decodes much earlier than before. A second processing step starts at 13.5 s, and the final one at 14.7 s. Overall decoding yield on crowded bands is improved by 10% or more. (Systems with receive latency greater than 0.2 s will see smaller improvements, but will still see many decodes earlier than before.) JT4: Formatting and display of Averaged and Deep Search decodes has been cleaned up and made consistent with other modes. Together with JT65 and QRA64, JT4 remains one of the digital modes widely for EME and other extreme weak-signal work on microwave bands. JT65: Many improvements for Averaged and Deep Search decodes and their display to the user. These improvements are particularly important for EME on VHF and UHF bands. WSPR: Significant improvements have been made to the WSPR decoder's sensitivity, its ability to cope with many signals in a crowded sub-band, and its rate of undetected false decodes. We now use up to three decoding passes. Passes 1 and 2 use noncoherent demodulation of single symbols and allow for frequency drifts up to ±4 Hz in a transmission. Pass 3 assumes no drift and does coherent block detection of up to three symbols. It also applies bit-by-bit normalization of the single-symbol bit metrics, a technique that has proven helpful for signals corrupted by artifacts of the subtraction of stronger signals and also for LF/MF signals heavily contaminated by lightning transients. With these improvements the number of decodes in a crowded WSPR sub-band typically increases by 10 to 15%. - New format for "EU VHF Contest" Tx2 and Tx3 messages When "EU VHF Contest" is selected, the Tx2 and Tx3 messages (those conveying signal report, serial number, and 6-character locator) now use hashcodes for both callsigns. This change is NOT backward compatible with earlier versions of _WSJT-X_, so all users of EU VHF Contest messages should be sure to upgrade to versiion 2.2.0. - Accessibility Keyboard shortcuts have been added as an aid to accessibility: Alt+R sets Tx4 message to RR73, Ctrl+R sets it to RRR. As an aid for partial color-blindness, the "inverted goal posts" marking Rx frequency on the Wide Graph's frequency scale are now rendered in a darker shade of green. - Minor enhancements and bug fixes "Save None" now writes no .wav files to disk, even temporarily. An explicit entry for "WW Digi Contest" has been added to "Special operating activities" on the "Settings | Advanced" tab. Contest mode FT4 now always uses RR73 for the Tx4 message. The Status bar now displays the number of decodes found in the most recent Rx sequence. Release candidate WSJT-X 2.2.0-rc1 will be available for beta-testing for one month starting on May 10, 2020. We currently plan a General Availability (GA) release of WSJT-X 2.2.0 on June 1, 2020. For those looking even farther ahead: We are well along in the development of two new modes designed for the LF and MF bands. One mode is for WSPR-like activity and one for making 2-way QSOs. Both use Low-density Parity Check (LDPC) codes, 4-GFSK modulation, and two-minute T/R sequences. The QSO mode reaches threshold SNR sensitivity around -31 dB on the AWGN channel, and the WSPR-like mode better than -32 dB. Release: WSJT-X 2.1.1 November 25, 2019 --------------------- WSJT-X 2.1.1 is a bug fix only release addressing regressions in the prior v2.1.0 release. - Document rules for the UDP message protocol. - Fix bug that could cause display of a blank Settings window. - Fix message parsing to properly handle 4-character directed CQs - Fix a potential crash in the interface to Omni-Rig. - Improve handling of unexpected rig off line status changes from Omni-Rig. - Add an option to highlight unworked 2-character grid fields rather than 4-character grid squares. - Fix bug that caused unwanted disabling of "Enable Tx" in Fox mode. - Log duplicate contacts in FT8 DXpedition Fox mode. - Regenerate the GFSK Tx waveform if Tx audio frequency is changed. - Fix the behavior of double-clicking on a decoded message with first callsign displayed as an unresolved hash code <...>. - Fix a problem with determining "worked before" status after a band change. - Updates to the WSJT-X 2.1 User Guide. - Fix a production issue with the macOS tool chain that generated broken executables. Release: WSJT-X 2.1 July 15, 2019 ------------------- WSJT-X 2.1 is a major update that introduces FT4, a new protocol targeted at HF contesting. Other improvements have been made in the following areas: - FT8 waveform generated with GMSK, fully backward compatible - user options for waterfall and spectrum display - contest logging - rig control - user interface - UDP messaging for inter-program communication - accessibility There are numerous minor enhancements and bug fixes. We now provide a separate installation package for 64-bit Windows 7 and later, with significant improvements in decoding speed. Release: WSJT-X 2.1.0-rc7 June 3, 2019 ------------------------- This release is a bug fix only release addressing regressions in the prior RC6 release. There are no functional changes other than an updated AD1C CTY.DAT database. Release: WSJT-X 2.1.0-rc6 June 2, 2019 ------------------------- Changes and bug fixes since WSJT-X 2.1.0-rc5: IMPORTANT CHANGES TO THE FT4 PROTOCOL *** NOT BACKWARD COMPATIBLE *** - T/R sequence length increased from 6.0 to 7.5 seconds - Symbol rate decreased from 23.4375 to 20.8333 baud - Signal bandwidth decreased from 90 Hz to 80 Hz OTHER FT4 IMPROVEMENTS - Allowable time offsets -1.0 < DT < +1.0 s - Tx4 message with RRR now allowed, except in contest messages - Audio frequency is now sent to PSK Reporter - Add a third decoding pass - Add ordered statistics decoding - Improved sensitivity: threshold S/N is now -17.5 dB - Improved S/N calculation - In FT4 mode, Shift+F11/F12 moves Tx freq by +/- 100 Hz OTHER IMPROVEMENTS - Improvements to accessibility - Updates to the User Guide (not yet complete, however) - New user option: "Calling CQ forces Call 1st" - N1MM Logger+ now uses the standard WSJT-X UDP messages - OK/Cancel buttons on Log QSO window maintain fixed positions - Put EU VHF contest serial numbers into the ADIF SRX and STX fields - Enhancements to the Omni-Rig CAT interface - New setting option to include or exclude WAE entities BUG FIXES - Fix generation of Tx5 message when one callsign is nonstandard - Fix a bug that prevented use on macOS - Fix a bug that caused mode switch from FT4 to FT8 - Fix a bug that caused FT4 to do WSPR-style band hopping - Fix a bug that caused a Fortran bounds error - Repaired field editing in the Contest Log window Release candidate WSJT-X 2.1.0-rc6 will be available for beta-testing through July 21, 2019. It will be inoperable during the ARRL June VHF QSO Party (June 8-10) or ARRL Field Day (June 22-23). It will permanently cease to function after July 21, 2019. If all goes according to plan, by that time there will be a General Availability (GA) release of WSJT-X 2.1.0. Release: WSJT-X 2.1.0-rc5 April 29, 2019 ------------------------- WSJT-X 2.1.0 fifth release candidate is a minor release including the following. - Repairs a defect that stopped messages from UDP servers being accepted. - Improved message sequencing a QSO end for CQing FT4 stations. - "Best S+P" action times out after two minutes waiting for a candidate. - Updated macOS Info.plist to comply with latest mic. privacy controls. - Multi-pass decoding for FT4 inc. prior decode subtraction. - Fast/Normal/Deep options for the FT4 decoder. - Proposed suggested working frequencies for the new FT4 mode. - Repair a defect in RTTY RU where sequencer fails to advance to Tx3. - Fix a defect where the contest serial # spin box was incorrectly hidden. - Fix defects in ALL.TXT formatting for JT65 and JT9. - Reduce timeout for AP decoding with own call from 10 mins to 5 mins. Release: WSJT-X 2.1.0-rc4 April 10, 2019 ------------------------- WSJT-X 2.1.0 fourth release candidate is a minor release including the following. - New "Call Best" button for FT4 mode to select the best reply to a CQ call based on neediness. - Fixed UTC display on FT4 waterfall. This release is made by invitation only to selected testers to trial the FT4 mode in semi-realistic contest simulations and to elicit feedback to guide future development. *Note* this release is not for general public release and we request that it is not distributed. Release: WSJT-X 2.1.0-rc3 April 5, 2019 ------------------------- WSJT-X 2.1.0 third release candidate is an enhancement release to change the implementation of the new FT4 mode to a synchronous T/R period of 6 seconds. This release is made by invitation only to selected testers to trial the FT4 mode in semi-realistic contest simulations and to elicit feedback to guide future development. *Note* this release is not for general public release and we request that it is not distributed. Release: WSJT-X 2.1.0-rc2 March 29, 2019 ------------------------- WSJT-X 2.1.0 second release candidate is a bug fix release to repair some usability issues with FT4 contest mode. The following new features are also included. - Better options for QSO flow by clicking Tx# buttons to transmit - A 64-bit package for Windows 64-bit systems - Improved FT4 sync detection speed This release is made by invitation only to selected testers to trial the FT4 mode in semi-realistic contest simulations and to elicit feedback to guide future development. *Note* this release is not for general public release and we request that it is not distributed. Release: WSJT-X 2.1.0-rc1 March 25, 2019 ------------------------- WSJT-X 2.1.0 first release candidate is a preview alpha quality release containing the following new features. - FT4 mode, a new mode targeted at HF digital contesting - GMSK modulation for FT4 and FT8 - New waterfall option to select between raw sensitivity or a filtered signal representation for best visualization of signal quality This release is made by invitation only to selected testers to trial the FT4 mode in semi-realistic contest simulations and to elicit feedback to guide future development. *Note* this release is not for general public release and we request that it is not distributed. Release: WSJT-X 2.0.1 February 25, 2019 --------------------- WSJT-X 2.0.1 is a bug fix release including the following defect repairs reported since the v2.0.0 GA release. - Remove startup message about importance of upgrading to v2.0. - Relax ADIF log file parsing to allow garbage between records and records with no DX callsign - Fix bug that prevented retention of power and comments in Log QSO window - Updates to User Guide - MSK144 frequency defaults to 50.260 in IARU Regions 2 and 3 - Remove hexadecimal RGB values from color-configuration panel - Fix a bounds error by not executing Fox-related code when not in Fox mode - Allow the logQSO dialog to modify "Exch Sent" or "Rcvd" when operating in RTTY or NA VHF Contest mode, and to have any changes flow through to N1MM Logger. - Fix several problems in handling hashed callsigns - More rigorous quality checking of WSPR decodes from the OSD algorithm - Fix bug that prevented recevied signal reports from compound callsigns to be logged - Improved recognition of callsigns with /P or /R suffixes - Do not waste time trying AP decoding of nonstandard callsigns - Make OSD decoding work with WSPR "type 2" messages - Retain in Tx6 message field any CQ messages like "CQ xxxx K1ABC FN42", where xxxx is 1-4 letters or 1-3 digits - Optional key bindings for F1 through F5, especially for contest use - Include grid in Tx1 messages with hashed callsign, for example " K1ABC FN42" - Better formatting for the files ALL.TXT and ALL_WSPR.TXT - Correct a flaw in validating contest exchange data when logging - Option to always start new decode periods at top of Band Activity window - New command "Erase WSPR hashtable" on the File menu - Improved validation for ARRL RTTY RU and FD exchange fields - UDP Reference applications join a multicast group on all available multicast capable network interfaces - Minor code changes to support Qt versions >=5.10 - Changes to support x64 Windows builds in preparation for Qt v5.12 - Add "ADIF Export ..." to Fox Log's contextual popup menu - Use ARRL-required names for VHF+ bands in exported Cabrillo log - New utility program rigctlcom-wsjtx (from Hamlib) - Remove temporary FT8 working frequencies from default frequency list - UDP protocol's Clear (3) message is made two-way, for better communication with DX Lab Suite applications - Reset QSO start time when aborting a QSO or clearing messages by ESC or F4 - Correct a logging issue in Fox's ADIF log when Fox sends RR73 to more than one Hound in the same Tx sequence. Release: WSJT-X 2.0 December 10, 2018 ----------------------- WSJT-X 2.0 is a major update that introduces new protocols for FT8 and MSK144. The new protocols become the world-wide standards on December 10, 2018. WSJT-X 2.0 cannot communicate in these modes with other stations using WSJT-X v1.9.1 or earlier. Please help by urging everyone to upgrade no later than January 1, 2019. New features since WSJT-X v1.9.1: 1. Compound and nonstandard callsigns are automatically recognized and handled using new message formats. 2. The new FT8 protocol provides optimized message formats for North American VHF contests, European VHF contests, ARRL Field Day, and ARRL RTTY Roundup. Similarly, the new MSK144 protocol provides optimized message formats for North American VHF and European VHF contests. Full support is provided for "/R" and "/P" calls in the relevant contests. 3. The new protocols provide nearly equal (or better) sensitivity compared to the old ones, and lower false decode rates. 4. New logging features are provided for contesting and for "Fox" (DXpedition) mode. Logging is optionally integrated with N1MM Logger+ and WriteLog. 5. Color highlighting of decoded messages provides worked-before status for callsigns, grid locators, DXCC entities, continents, CQ Zones, and ITU zones on a “by band” and “by mode” basis, and for stations that have uploaded their logs to Logbook of the World (LoTW) within a specified time interval. 6. The WSPR decoder now achieves decodes down to S/N = -31 dB. For the particular benefit of LF/MF users, an option "No own call decodes" has been added. 7. The UDP messages sent to companion programs have been expanded and improved. Some details of changes since WSJT-X-rc5 include the following: - Initial load of ADIF log in background - Correct the UTC displayed in Fox/Contest log - Faster entry and correct scrolling for Fox/Contest log - Add contest exchanges and contest type to UDP logged QSO message - Fix a bug that suppressed decodes with negative DT. - AK and HI are DXCCs, not states, for RTTY Roundup - Fix improper truncation of some non-FT8 messages in ALL.TXT - Various minor bug fixes and code cleanup - Update the WSJT-X User Guide to v2.0 (more to come...) - Update cty.dat Release: WSJT-X 2.0-rc5 November 26, 2018 ----------------------- Release Candidate 5 ("RC5") is stable, works well, and fixes the known problems in RC4. It is likely that the General Availability (GA) release of WSJT-X 2.0 will be nearly identical to RC5. Changes from WSJT-X 2.0-rc4 include the following: - Make the "Auto Seq" checkbox sticky, again - Remove the 5-minute mouse timer - Correct the "worked before" logic for color highlighting - Add "No own call decodes" checkbox in WSPR mode - Display and log UTC (not local time) in contest operations - Validate contest QSO details before allowing logging - Force Aqua theme on macOS to avoid issues with Mojave dark theme - Move Fox log Reset action to Fox log window context menu - Improve layout of Working Frequencies and Station Information tables - Allow deletes and editing in Fox and Contest log windows - Add Tool Tips for Fox and Contest log windows - Fix a bug causing false AP decodes in JT65 VHF+ operation - Fix a bug that could switch unexpectedly from JT65 to JT9 mode PLEASE NOTE: As far as WSJT-X 2.0 (RC4, RC5, and GA releases) are concerned, signals using the old FT8 protocol are undecodable interference. This means that regenerated replicas cannot be subtracted from received data, and consequently second- and third-pass decodes may be impeded. Full performance of the 77-bit decoder will not be realized until most signals on a crowded band are using the new FT8 protocol. Release: WSJT-X 2.0-rc4 November 12, 2018 ----------------------- Changes from WSJT-X Version 2.0.0-rc3 include the following: - Fix the "cannot open file fort.81" bug - Avoid too many redirect loops related to openSSL support - Fix the auto-generated messages for nonstandard callsigns - Remove all support for the legacy FT8 protocol - Disallow selecting MSK144 with RTTY or Field Day messages active - Correct and expand support for color highlighting decoded messages - ESC key aborts a QSO, clears DX Call, and selects Tx6 - Disable "nextCall" procedure for RTTY contest; it still needs work - Correct a flaw in handling MSK144 Sh messages - Prevent Fox from inadvertently toggling Tx 1st/Even - Re-organize the Fox/Hound/Contest selection boxes - Improve the validators for contest exchange boxes - Disable Tx after 5 minutes of no mouse movement - Remove end-of-line AP info when using contest messages - Fix forwarding of Sent and Rcvd exchanges to N1MM+ and ADIF log - Don't auto-log a QSO with incomplete exchange info - Fix two sequencing flaws after double-clicks on a decoded msg - New facilities for Contest and Fox-mode logging Release: WSJT-X 2.0-rc3 October 15, 2018 ----------------------- Changes from WSJT-X Version 2.0.0-rc2 include the following: - Improved SNR calculation for FT8 - Test grid4 (not grid6) for matches in ADIF log - Auto-generate 77-bit messages for callsigns with /R or /P - Fix auto-sequencing for "CQ ABC ...", "CQ ABCD ...", etc. - Fix the "CQ RU RU ..." bug - Implement AP decoding for contest messages and for Hound - Check Field Day and RTTY Roundup exchanges for validity - Implement "Select next caller" and use of "TU; ..." messages - Option to "auto log" in contests - Real-time display of contest log - Contest exchanges sent to ADIF log and N1MM+ - Function to export Cabrillo log - Convert DXpedition mode to always use 77-bit messages - Fix bug associated with opening "houndcallers.txt" - Remove end-of-line numbers from MSK144 decodes - Finish MSK144 encoding/decoding for Sh msgs and nonstandard calls - Halt Tx before resetting power after Tune - Auto update of LoTW info, and faster program startup Release: WSJT-X 2.0-rc2 September 25, 2018 ----------------------- Changes from WSJT-X Version 2.0.0-rc1 include the following: - Corrected a flaw that encoded a message's first callsign as hexadecimal telemetry data if the call consisted only of letters A-F and digits 0-9. - Corrected program logic that failed to identify certain callsigns as "nonstandard". - Fixed a bug that color-highlighted bare CQ messages (no grid locator) as "New DXCC". - Fixed a bug that failed to log Report Sent if MyCall is a nonstandard call. - Fixed a bug that generated incorrect MSK144 tones for certain messages and caused a "memory" effect on stations receiving the incorrect tones. - Fixed several bugs that could cause certain Tx messages to crash the program. - Suppressed the display of certain illogical false decodes. Release: WSJT-X 2.0-rc1 September 17, 2018 ----------------------- This is the first candidate release on WSJT-X 2.0, intended for beta-level testing. For details see: http://physics.princeton.edu/pulsar/k1jt/New_Features_WSJT-X_2.0.txt http://physics.princeton.edu/pulsar/k1jt/Quick_Start_WSJT-X_2.0.pdf http://physics.princeton.edu/pulsar/k1jt/77bit.txt Release: WSJT-X Version 1.9.1 May 31, 2018 ----------------------------- This release is a critical bug fix release that removes an unintended restriction of FT8 DXpedition mode. Release: WSJT-X Version 1.9.0 May 28, 2018 ----------------------------- Changes from WSJT-X Version 1.9.0-rc4 include the following: - Display in the right text window of MSK144 messages addressed to "MyCall" has been restored. - Fox is not allowed to transmit in any of the default FT8 sub-bands. - Fox can now work Hounds using compound callsigns. - Fox can now transmit free-text messages (and any standard FT8 message) by using Tab 1 or Tab 2. - Added a checkbox to enable more frequent programmed CQs by Fox. Default is OFF. - Alt+N keyboard shortcut has been restored. - MacOS program crash on unexpected decode request has been fixed. - Several minor bug fixes and added convenience features. - Hamlib, support for TRXManger added. - Hamlib, improved support for flrig. Release: WSJT-X Version 1.9.0-rc4 April 30, 2018 --------------------------------- Changes from WSJT-X Version 1.9.0-rc3 include the following: - Corrected a number of flaws in Fox and Hound behavior, FT8 DXpedition Mode - Decoded CQ calls where a prefix has been used as a suffix should have the DXCC entity name assigned correctly in almost all cases - Improved AFC capability for the wider JT65 sub-modes to help with drifting signals - Better support for macOS using hi-DPI Retina displays - New UDP message that allows external applications to highlight decoded callsigns - Main-screen geometry and state of the "splitter" setting between its two text windows is now properly restored after program restart. - New simulator jt49sim[.exe] replaces jt4sim and jt9sim - Correct S/N measurements for the JT9 slow/wide submodes - Other minor bug fixes - Updated copy of cty.dat Release: WSJT-X Version 1.9.0-rc3 March 18, 2018 --------------------------------- Changes from WSJT-X Version 1.9.0-rc2 include the following: - Corrected a number of flaws in Fox behavior, FT8 DXpedition Mode - Allow Hounds to use compound callsigns - Write debugging information to FoxQSO.txt. - Fix the "Blue Decode Button" bug - Allow partial processing of incoming UDP Reply messages so that non-CQ/QRZ decodes can be processed. The processing is the same as double-clicking the same decoded message within WSJT-X except that "Enable Tx" will not be enabled. - Send DX grid locator to wsjt_status.txt, for use by applications like PstRotatorAZ - Correct the display of DXCC status of KG4 calls - Updated copy of cty.dat - Updates to documentation - Other minor bug fixes - This release contains updated Hamlib functionality including changes to the Yaesu FT-817 back end that allows the uBITx kit transceiver to be CAT controlled by WSJT-X. Release: WSJT-X Version 1.9.0-rc2 February 26, 2018 --------------------------------- Changes from WSJT-X Version 1.8.0 include the following: - New FT8 DXpedition Mode to facilitate high QSO rates in pileup situations - Decoding improvements for JT65 mode, including a priori (AP) decoding when VHF/UHF/Microwave features are enabled - Optional Auto-Sequencing in JT4, JT9, and JT65 when VHF/UHF/Microwave features are enabled - Better suppression of low-confidence false decodes generated by AP decoding in FT8 mode - Improved decoding performance for WSPR mode, especially effective at LF and MF - Minor adjustments to auto-sequencing behavior - More flexible Doppler control features for EME - Improved waterfall sensitivity for very weak signals - Automatic real-time forwarding of logged information to N1MM Logger+ - Expanded and improved UDP messages sent to companion programs - Bug fixes and other minor tweaks to user interface A primary purpose of this beta release is to allow field testing of FT8 DXpedition Mode. Instructions for this mode are posted here: http://physics.princeton.edu/pulsar/k1jt/FT8_DXpedition_Mode.pdf Contacts in FT8 DXpedition Mode must use WSJT-X v1.9.0 at both ends of the QSO. Please report any anomalous behavior to email list wsjt-devel@lists.sourceforge.net. You must be a subscriber in order to post there. Release: WSJT-X Version 1.8.0 October 27, 2017 ----------------------------- This is the full General Availability release of WSJT-X Version 1.8.0. Changes from WSJT-X Version 1.8.0-rc3 are very minor: - Right-click on the Wide Graph now pops up a Context Menu. Select the item *Set Rx & Tx Offset* to complete a one-handed setting of both red and green frequency markers. - Several clarifications and additions to Tool Tips and the User Guide. We recommend that all users should upgrade to WSJT-X Version 1.8.0. If you upgrade from v1.8.0-rc1 it may be necessary to do a one-time reset of the default list of suggested operating frequencies. Go to *File->Settings->Frequencies*, right click on the table and select *Reset*. Release: WSJT-X Version 1.8.0-rc3 October 16, 2017 --------------------------------- Most (but not all) changes since Version 1.8.0-rc2 involve user control of the increasingly popular FT8 mode. The "RC3" release also includes minor bug fixes and updates to the WSJT-X User Guide. The following list includes all of the more important changes: - New optimization of GUI for simplex and split behavior in FT8 mode. 1. Checkbox "Lock Tx Freq" on main window is relabeled "Hold Tx Freq". 2. Double-clicking on decoded messages that do not contain your own call moves both Rx and Tx frequencies. If the first callsign is your own call, only Rx freq moves. 3. Double-clicking on decoded messages moves the Rx frequency. If "Hold Tx Freq" is checked, Tx frequency is moved only if CTRL was held down. 4. Clicking on the waterfall moves Rx and Tx frequencies as before: Rx only on a simple click, Tx only on SHIFT-click, and both on CTRL-click. This happens even if "Hold Tx Freq" is checked. - Add a semi-automated "FreqCal" procedure: see *Solve for calibration parameters* on the Tools menu. - Improv auto-sequencing behavior: stop and on-frequency transmission if a called station comes back to someone else. - Improve S/N estimation in some situations involving QRM. - Fix an initialization issue with user-modified application fonts. - Fix an issue with Tx5 message generation with Type 2 compound calls. - Enhance and improve the ADIF parser of logbook records. Update the band limits as per ADIF 3.0.6 specification. - Increase the FT8 DT range to +/- 2.5 s. - Do not allow window manager events to close the astronomical data window. - Add an "Erase" item to the context (right-click) menu for decoded text. - Extend UDP messages with an "off air" boolean field indicating that the decode was derived from a .WAV file playback rather than an on air reception. - Extend reference applications to use the new off air decode message field. - Improve performance of FT8 decoder, especially for overlapping signals. - Allow specialized use of "x2 Tone Spacing" in FT8 and slow JT9 modes. - Move "NA VHF Contest Mode" checkbox to main screen. Query the operator if d > 10000 km. - Adjust UI to improve portability with font size changes and between platforms. - Extend UDP Reply message to support keyboard modifiers. This allows UDP servers to emulate keyboard modified double-clicks on decoded messages, e.g. ALT+double-click for replying to a CQ or QRZ call without changing ones Tx frequency offset. - Update the cty.dat file (21st Sept 2017). - Ensure that Fast Graph is properly initialized. - Better handling of worked before and country name display. Appended text is added at a fixed column unless the message overlaps in which case the appended information floats to the right. - Restore printing of MSK144 decode quality information. - Display Echo Graph automatically when Echo mode is started. - Fix a bug that prevented double-click on a JT65 EME-style "OOO" message from populating the Tx message boxes. - Fixed behavior with double-click on 'CQ .' - Update the "blank line" divider with band ID at 4*TRperiod/5. - Fix cty.dat lookups that were not honouring exact match flags - Add some further Copyright protections. - Fix a bug involving "firstcall contains mycall" but not equal to mycall. - Fix an issue with editing IARU regions in the working frequencies table. Release: WSJT-X Version 1.8.0-rc2 September 2, 2017 --------------------------------- Implementation of FT8 and its auto-sequencing feature is now more capable and more polished. The decoder is faster and better: it now includes signal subtraction, multi-pass decoding, and the use of accumulated "a priori" information as a QSO progresses. Sensitivity extends downward as far as -24 dB in some circumstances. Overlapping signals 2 and 3 deep are frequently decoded at essentially the same frequency. On a crowded band we sometimes see more than 30 decodes in a single 15-second interval, over a 2 kHz window. The North American VHF Contesting Mode has been extended to include both FT8 and MSK144 modes. The "RC2" release also includes many minor bug fixes and an extensively updated WSJT-X User Guide. Depending on what code revision you upgrade from, it may be necessary to do a one-time reset of the default list of suggested operating frequencies. Go to *File->Settings->Frequencies*, right click on the table and select *Reset*. Release: WSJT-X Version 1.8.0 ----------------------------- NEW FEATURES IN WSJT-X Version 1.8.0 ------------------------------------ 1. New mode called FT8: sensitivity down to -20 dB on the AWGN channel; QSOs 4 times faster than JT65 or JT9; auto-sequencing includes an option to respond automatically to first decoded reply to your CQ. 2. New mode for accurate Frequency Calibration of your radio. 3. Improved performance of decoders for JT65, QRA64, and MSK144. MSK144 includes facilities for amplitide and phase equalization and an "SWL" mode for short-format messages. 4. Options to minimize screen space used by Main and Wide Graph windows. 5. Enhanced management scheme for table of operating frequencies, and a new set of default frequencies specific to the three IARU Regions. 6. Improved CAT control for many rigs, including those controlled through Commander or OmniRig. 7. New keyboard shortcuts to set "Tx even/1st" ON or OFF. 8. A number of (mostly minor) bug fixes and tweaks to the user interface. For example: new behavior for the audio level slider; correctly logged QSO start times in certain situations; correct control of FT-891/991 and some other radios via rigctld. At the time of the v1.8.0-rc1 release the following tasks are yet to be completed: 1. Updates to WSJT-X User Guide. 2. Sample files for FT8. 3. Enhanced decoding using AP ("a priori") information. 4. Signal subtraction and multi-pass decoding. 5. Option to Auto-respond to the weakest responder to your CQ. Installation packages for Windows, Linux, OS X, and Raspbian can be downloaded from the WSJT web site: http://physics.princeton.edu/pulsar/K1JT/wsjtx.html Please send bug reports to either wsjtgroup@yahoogroups.com or wsjt-devel@lists.sourceforge.net. Such reports should include a full prescription of steps to reproduce the undesired behavior. You must be a subscriber to post to either of these lists. Brief Description of the FT8 Protocol ------------------------------------- WSJT-X Version 1.8.0 includes a new mode called FT8, developed by K9AN and K1JT. The mode name "FT8" stands for "Franke and Taylor, 8-FSK modulation". FT8 uses 15-second T/R sequences and provides 50% or better decoding probability down to -20 dB on an AWGN channel. An auto-sequencing facility includes an option to respond automatically to the first decoded reply to your CQ. FT8 QSOs are 4 times faster than those made with JT65 or JT9. FT8 is an excellent mode for HF DXing and for situations like multi-hop E_s on 6 meters, where deep QSB may make fast and reliable completion of QSOs desirable. Some important characteristics of FT8: - T/R sequence length: 15 s - Message length: 75 bits + 12-bit CRC - FEC code: LDPC(174,87) - Modulation: 8-FSK, tone spacing 6.25 Hz - Constant-envelope waveform - Occupied bandwidth: 50 Hz - Synchronization: 7x7 Costas arrays at start, middle, and end - Transmission duration: 79*1920/12000 = 12.64 s - Decoding threshold: -20 dB; several dB lower with AP decoding - Multi-decoder finds and decodes all FT8 signals in passband - Optional auto-sequencing and auto-reply to a CQ response - Operational behavior similar to JT9, JT65 We plan to implement signal subtraction, two-pass decoding, and use of a priori (AP) information in the decoder. These features are not yet activated in v1.8.0. We haven't yet finalized what the three extra bits in the message payload will be used for. Suggestions are welcome! ++++++ -- Joe, K1JT, for the WSJT Development Team