Release: WSJT-X Version 1.7.0 ----------------------------- Short list of new features -------------------------- 1. New modes: ISCAT, MSK144, QRA64. 2. Newly implemented submodes: JT65B-C, JT9B-H (wide and fast). 3. FT decoder replaces KV decoder for JT65; KVASD is no longer used. 4. Improvements to JT4, JT9, and JT65 decoders. 5. Multi-pass decoding now implemented for JT65 as well as WSPR. 6. Many improvements to Rig Control. 7. Improved convenience features for EME Doppler tracking. 8. Multiple configurations can be saved and restored. 9. Sample-file download facility. 10. Optional auto-sequencing for Fast modes. 11. Power settings optionally remembered for Transmit and Tune on a band-by-band basis. New Modes --------- 1. MSK144 is intended for meteor scatter at 50 MHz and higher. It uses a low-density parity check code (LDPC) designed by Steve Franke, K9AN. The mode is a direct descendant of the now-defunct mode JTMSK, with a number of improvements for better performance on weak and short meteor pings. The effective character transmission rate is about 250 cps, compared with 147 cps for FSK441. Like JT4, JT9, JT65, and QRA64, MSK144 uses strong forward error correction. Message decoding is all or nothing: partial decodes do not occur, and you will see little or no garbage on your screen. Standard MSK144 message frames are 72 ms long, compared with about 120 ms for an equivalent FSK441 message. The MSK144 waveform allows coherent demodulation, allowing up to 3 dB better sensitivity. After QSO partners have exchanged callsigns, MSK144 can use even shorter messages, only 20 ms long. As in all the fast modes in WSJT-X, the 72 ms (or 20 ms) messages are repeated without gaps for the duration of a transmission cycle. For most purposes we recommend a T/R cycle duration of 15 s, but 5 s and 10 s sequences are also supported. Short ("Sh") messages in MSK144 are intended primarily for 144 MHz and higher frequencies, where most pings are very short. These messages do not contain full callsigns; instead, they contain a hash of the two callsigns along with a report, acknowledgement, or 73. Short messages are fully decodable only by the station to whom they are addressed, as part of an ongoing QSO, because only then will the received hash match that calculated using the known strings for "My Call" and "DX Call". If you are monitoring someone else's QSO, you will not be able to decode its Sh messages. An MSK144 signal occupies the full bandwidth of a typical SSB transmitter, so transmissions are always centered at an offset of 1500Hz. For best results, selectable or adjustable Rx and Tx filters should be set to provide the flattest possible response over at least 300 - 2700 Hz. The maximum permissible frequency offset between you and your QSO partner is 200 Hz, and less is better. 2. QRA64 is a intended for EME and other weak-signal use. Its internal code was designed by Nico Palermo, IV3NWV, and implemented in WSJT-X by K1JT. The protocol uses a "Q-ary Repeat Accumulate" code -- along with LDPC, another one of the latest research areas in communication theory. The QRA64 code is inherently better than the Reed Solomon (63,12) code used in JT65, yielding already a 1.3 dB advantage. QRA64 uses a new synchronizing scheme based on a 7 x 7 Costas array, so you will not see a bright sync tone at the lowest tone frequency. This change yields another 1.9 dB advantage. In most respects our implementation of QRA64 is operationally similar to JT65. QRA64 does not use two-tone shorthand messages, and it makes no use of a callsign database. Rather, additional sensitivity is gained by making use of "already known" information as a QSO progresses -- for example, when reports are being exchanged and you have already decoded both callsigns in a previous transmission. QRA64 presently offers no message averaging capability, though that may be added. In our early tests, many EME QSOs have already been made using submodes QRA64A-E on bands from 144 MHz to 10 GHz. 3. ISCAT is essentially the same as in recent versions of program WSJT. For details consult the WSJT User Guide: http://physics.princeton.edu/pulsar/K1JT/doc/wsjt/ Program Setup ------------- Many of the new program capabilities are enabled when you check "Enable VHF/UHF/Microwave features" on the Settings | General tab. For MSK144 mode, we suggest setting "T/R 15 s" and "F Tol 100 Hz". Check "Sh" to enable the use of short messages and "Auto Seq" for auto-sequencing. For QRA64 mode, set Tx and Rx frequencies to 1000 Hz. We encourage you to check "Save all" when making tests, and to save any of the resulting .wav files that might help us to improve program performance or behavior, or to illustrate a problem that you identify. Final Comments -------------- We will be grateful for any and all reports from users; these will surely help us to make further improvements to WSJT-X. The most helpful bug reports describe the problem clearly and include a complete recipe to reproduce it. Feature requests are also welcome. Send your reports to wsjtgroup@yahoogroups.com, or to the developers list wsjt-devel@lists.sourceforge.net.