mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-22 04:11:16 -05:00
55b74f5a0e
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8030 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
75 lines
3.5 KiB
Plaintext
75 lines
3.5 KiB
Plaintext
=== Frequency Calibration
|
|
|
|
Many _WSJT-X_ capabilities depend on signal-detection bandwidths no
|
|
more than a few Hz. Frequency accuracy and stability are therefore
|
|
unusually important. We provide tools to enable accurate frequency
|
|
calibration of your radio, as well as precise frequency measurement of
|
|
on-the-air signals. The calibration procedure works by automatically
|
|
cycling your CAT-controlled radio through a series of preset
|
|
frequencies of carrier-based signals at reliably known frequencies,
|
|
measuring the error in dial frequency for each signal.
|
|
|
|
You will probably find it convenient to define and use a special
|
|
<<CONFIG-MENU,Configuration>> dedicated to frequency calibration.
|
|
Then complete the following steps, as appropriate for your system.
|
|
|
|
- Switch to FreqCal mode
|
|
|
|
- In the _Working Frequencies_ box on the *Settings -> Frequencies*
|
|
tab, delete any default frequencies for *FreqCal* mode that are not
|
|
relevant for your location. You may want to replace some of them with
|
|
reliably known frequencies receivable at your location.
|
|
|
|
TIP: We find major-city AM broadcast stations generally serve well as
|
|
frequency calibrators at the low frequency end of the spectrum. In
|
|
North America we also use the standard time-and-frequency broadcasts
|
|
of WWV at 2.500, 5.000, 10.000, 15.000, and 20.000 MHz, and CHU at
|
|
3.330, 7.850, and 14.670 MHz. Similar shortwave signals are available
|
|
in other parts of the world.
|
|
|
|
- During the calibration procedure, the radio's USB dial frequency is
|
|
offset 1500 Hz below each *FreqCal* entry in the default frequencies
|
|
list. As shown in the screen shot below, detected signal carriers
|
|
therefore appear at about 1500 Hz in the WSJT-X waterfall.
|
|
|
|
image::FreqCal.png[align="left",alt="FreqCal"]
|
|
|
|
With modern synthesized radios, small measured offsets from 1500 Hz
|
|
will exhibit a straight-line dependence on frequency. You can
|
|
approximate the calibration of your radio by simply dividing the
|
|
measured frequency offset (in Hz) at the highest reliable frequency by
|
|
the nominal frequency itself (in MHz). For example, the 20 MHz
|
|
measurement for WWV shown above produced a measured tone offset of
|
|
24.6 Hz, displayed in the _WSJT-X_ decoded text window. The resulting
|
|
calibration constant is 24.6/20=1.23 parts per million. This number
|
|
may be entered as *Slope* on the *settings -> Frequencies* tab.
|
|
|
|
A more precise calibration can be effected by fitting the intercept
|
|
and slope of a straight line to the whole sequence of calibration
|
|
measurements, as shown for these measurements in the graph plotted
|
|
below. Software tools for completing this task are included with the
|
|
_WSJT-X_ installation, and detailed instructions for their use are
|
|
available at https://physics.princeton.edu/pulsar/k1jt/FMT_User.pdf.
|
|
Using these tools and no specialized hardware beyond your
|
|
CAT-interfaced radio, you can calibrate the radio to better than 1 Hz
|
|
and compete very effectively in the ARRL's periodic Frequency
|
|
Measuring Tests.
|
|
|
|
image::FreqCal_Graph.png[align="left",alt="FreqCal_Graph"]
|
|
|
|
=== Reference Spectrum
|
|
|
|
WSJT-X provides a tool that can be used to determine the detailed
|
|
shape of your receiver's passband. Disconnect your antenna or tune to
|
|
a quiet frequency with no signals. With WSJT-X running in one of the
|
|
slow modes, select *Measure reference spectrum* from the *Tools* menu.
|
|
Wait for about a minute and then hit the *Stop* button. A file named
|
|
`refspec.dat` will appear in your log directory.
|
|
|
|
[ ... TBD ... ]
|
|
|
|
=== Equalization
|
|
|
|
[ ... TBD ... ]
|
|
|