WSJT-X/doc/source/configuration-station.adoc
Joe Taylor 43664a2e01 Another round of documentation updates.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3669 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2014-01-29 20:50:18 +00:00

62 lines
2.8 KiB
Plaintext
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// Status=review
- Start _WSJT-X_ and select *Configuration* from its *Setup* menu. Enter
the following information:
* *Call Sign*: <Your Call Sign>
* *Grid*: <Your Maidenhead locator>
* *PTT method*: choose from RTS, DTR, CAT, VOX, or None.
* *PTT port*: if you will use RTS or DTR, choose a serial port.
* *PSK Reporter*: check to enable sending reception reports to the
{pskreporter} mapping facility.
* *CW ID*: Check to send your callsign in CW after sending 73.
* *CW Interval*: set the time interval for sending your CW identification.
Default is 0 (never).
_WSJT-X_ does not implement full transceiver control, but it provides a
way to ensure that _WSJT-X_ can read and set the radios dial
frequency. To enable this capability:
- Check the box *Enable CAT*
- Select your radio type from a drop-down list
- Select a *CAT port* (not the same port selected for PTT control)
TIP: If you need an additional item in the list of devices for the
CAT port, edit the configuration file +wsjtx.ini+ and add your
requirement as +CATdriver=<yourdriver>+ (for example,
+CATdriver=/dev/tty.usbserial+) in the group of entries marked
+[Common]+.
- Set the port parameters *Serial rate*, *Handshake*, *Data bits*,
*Stop bits* as required for your radio
- If you use {dxlcommander} or {hrd} to control your transceiver, you
can configure _WSJT-X_ to communicate with the radio through that
program. Entries for these programs appear at the end of the
drop-down list of supported rigs.
[[FIG_CONFIG_STATION]]
image::images/r3666-config-screen-80.png[align="center",alt="Configuration Screen"]
Leave *Split Tx* unchecked for now. If you are using CAT control, most
radios will allow you to set *PTT method* = CAT. Some radios support
two types of PTT assertion via CAT control: one takes audio input from
the Mic connector, the other from a rear-panel Data connector. The
simplest CAT configuration sets *Polling interval* = 0 (no polling the
radio for dial frequency). _WSJT-X_ can then set the radios
frequency, but the program will be unaware of subsequent changes made
using the radios panel controls.
With most radios you can set *Polling interval* to a small number (say
1 3 s) and the program will follow any frequency changes made at the
radio. Note that you may not be able simultaneously to control the
radio from _WSJT-X_ and from another program. Some experimentation
may be required; refer to the documentation for your rig-control
software and your radio. It is best to have the radio and any
interface equipment turned on and connected before starting _WSJT-X_,
and to exit the program before turning the equipment off.
- Click the *Test CAT Control* and *Test PTT* buttons to see that you
have established the desired control of station functions.
- Select the devices you will use for *Audio In* and *Audio Out*.
- Click *OK* to dismiss the *Configuration* window.