mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-09-04 20:36:39 -04:00
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7333 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
292 lines
12 KiB
Plaintext
292 lines
12 KiB
Plaintext
_WSJT-X_ v1.7 introduces a number of new features designed for use
|
|
on the VHF and higher bands. These features now include:
|
|
|
|
- *JT4*, a mode particularly useful for EME on the microwave bands
|
|
|
|
- *JT9* fast modes, useful for scatter propagation on VHF bands
|
|
|
|
- *QRA64*, a mode for EME using a "`Q-ary Repeat Accumulate`" code,
|
|
a low-density parity-check (LDPC) code using a 64-character symbol
|
|
alphabet
|
|
|
|
- *MSK144*, a mode for meteor scatter using a binary LDPC code and
|
|
Offset Quadrature Phase-Shift Keying (OQPSK). The resulting waveform
|
|
is sometimes called Minimum Shift Keying (MSK).
|
|
|
|
- *ISCAT*, intended for aircraft scatter and other types of scatter
|
|
propagation
|
|
|
|
- *Echo* mode, for detecting and measuring your own lunar echoes
|
|
|
|
- *Doppler tracking*, which becomes increasingly important for EME
|
|
on bands above 1.2 GHz.
|
|
|
|
- *Auto-sequencing* of transmitted messages for the fast modes with
|
|
forward error control
|
|
|
|
[[VHF_SETUP]]
|
|
=== VHF Setup
|
|
|
|
To activate the VHF-and-up features:
|
|
|
|
- On the *Settings | General* tab check *Enable VHF/UHF/Microwave
|
|
features* and *Single decode*.
|
|
|
|
- For EME, check *Decode at t = 52 s* to allow for extra path delay on
|
|
received signals.
|
|
|
|
- If you will use automatic Doppler tracking and your radio accepts
|
|
frequency-setting commands while transmitting, check *Allow Tx
|
|
frequency changes while transmitting*. Transceivers known to permit
|
|
such changes include the IC-735, IC-756 Pro II, IC-910-H, FT-847,
|
|
TS-590S, TS-590SG, TS-2000 (with Rev 9 or later firmware upgrade),
|
|
Flex 1500 and 5000, HPSDR, Anan-10, Anan-100, and KX3. To gain full
|
|
benefit of Doppler tracking your radio should allow frequency changes
|
|
under CAT control in 1 Hz steps.
|
|
|
|
NOTE: If your radio does not accept commands to change frequency
|
|
while transmitting, Doppler tracking will be approximated with a
|
|
single Tx frequency adjustment before a transmission starts, using a
|
|
value computed for the middle of the Tx period.
|
|
|
|
- On the *Radio* tab select *Split Operation* (use either *Rig* or
|
|
*Fake It*; you may need to experiment with both options to find one
|
|
that works best with your radio).
|
|
|
|
- On the right side of the main window select *Tab 1* to present the
|
|
traditional format for entering and choosing Tx messages.
|
|
|
|
The main window will reconfigure itself as necessary to display
|
|
controls supporting the features of each mode.
|
|
|
|
- If you are using transverters, set appropriate frequency offsets on
|
|
the *Settings | Frequencies* tab. Offset is defined as (transceiver
|
|
dial reading) minus (on-the-air frequency). For example, when using a
|
|
144 MHz radio at 10368 MHz, *Offset (MHz)* = (144 - 10368) =
|
|
-10224.000. If the band is already in the table, you can edit the
|
|
offset by double clicking on the offset field itself. Otherwise a new
|
|
band can be added by right clicking in the table and selecting
|
|
*Insert*.
|
|
|
|
image::Add_station_info.png[align="center",alt="Station information"]
|
|
|
|
- On the *View* menu, select *Astronomical data* to display a window
|
|
with important information for tracking the Moon and performing
|
|
automatic Doppler control. The right-hand portion of the window
|
|
becomes visible when you check *Doppler tracking*.
|
|
|
|
image::Astronomical_data.png[align="center",alt="Astronomical data"]
|
|
|
|
Three different types of Doppler tracking are provided:
|
|
|
|
- Select *Full Doppler to DX Grid* if you know your QSO partner's locator
|
|
and he/she will not be using any Doppler control.
|
|
|
|
- Select *Receive only* to enable EME Doppler tracking of your receive
|
|
frequency to a specific locator. Your Tx frequency will remain fixed.
|
|
|
|
- Select *Constant frequency on Moon* to correct for your own one-way
|
|
Doppler shift to or from the Moon. If your QSO partner does the same
|
|
thing, both stations will have the required Doppler compensation.
|
|
Moreover, anyone else using this option will hear both of you
|
|
without the need for manual frequency changes.
|
|
|
|
- See <<ASTRODATA,Astronomical Data>> for details on the quantities
|
|
displayed in this window.
|
|
|
|
=== JT4
|
|
|
|
JT4 is designed especially for EME on the microwave bands, 2.3 GHz and
|
|
above.
|
|
|
|
- Select *JT4* from the *Mode* menu. The central part of the main
|
|
window will look something like this:
|
|
|
|
image::VHF_controls.png[align="center",alt="VHF Controls"]
|
|
|
|
- Select the desired *Submode*, which determines the spacing of
|
|
transmitted tones. Wider spacings are used on the higher microwave
|
|
bands to allow for larger Doppler spreads. For example, submode JT4F
|
|
is generally used for EME on the 5.7 and 10 GHz bands.
|
|
|
|
- For EME QSOs some operators use short-form JT4 messages consisting
|
|
of a single tone. To activate automatic generation of these messages,
|
|
check the box labeled *Sh*.
|
|
|
|
- Select *Deep* from the *Decode* menu. You may also choose to
|
|
*Enable averaging* over successive transmissions and/or *Enable deep
|
|
Search* (correlation decoding).
|
|
|
|
image::decoding_depth.png[align="center",alt="Decoding Depth"]
|
|
|
|
The following screen shot shows one transmission from a 10 GHz EME
|
|
QSO using submode JT4F.
|
|
|
|
image::JT4F.png[align="center",alt="JT4F"]
|
|
|
|
=== JT65
|
|
|
|
In many ways JT65 operation on VHF and higher bands is similar to HF
|
|
usage, but a few important differences should be noted. Typical
|
|
VHF/UHF operation involves only a single signal (or perhaps two or
|
|
three) in the receiver passband. You may find it best to check
|
|
*Single decode* on the *Settings -> General* tab. There will be
|
|
little need for *Two pass decoding* on the *Advanced* tab. With VHF
|
|
features enabled the JT65 decoder will respond to special message
|
|
formats often used for EME: the OOO signal report and two-tone
|
|
shorthand messages for RO, RRR, and 73. These messages are always
|
|
enabled for reception; they will be automatically generated for
|
|
transmission if you check the shorthand message box *Sh*.
|
|
|
|
Be sure to check *Deep* on the *Decode* menu; you may optionally
|
|
include *Enable averaging* and *Deep search*.
|
|
|
|
The following screen shot shows three transmissions from a 144 MHz EME
|
|
QSO using submode JT65B and shorthand messages. Take note of the
|
|
colored tick marks on the Wide Graph frequency scale. The green
|
|
marker at 1220 Hz indicates the selected QSO frequency (the frequency
|
|
of the JT65 Sync tone) and the *F Tol* range. A green tick at 1575 Hz
|
|
marks the frequency of the highest JT65 data tone. Orange markers
|
|
indicate the frequency of the upper tone of the two-tone signals for
|
|
RO, RRR, and 73.
|
|
|
|
image::JT65B.png[align="center",alt="JT65B"]
|
|
|
|
=== QRA64
|
|
|
|
QRA64 is an experimental mode in the Version 1.7 alpha release of
|
|
_WSJT-X_. In most ways you will find operation of QRA64 similar to
|
|
JT65. The following screen shot shows an example of a QRA64C
|
|
transmission from DL7YC recorded at G3WDG over the EME path at 24 GHz,
|
|
at a time when Doppler spread on the path was 78 Hz. The red curve
|
|
with a peak at 967 Hz shows that the decoder has detected its
|
|
synchronizing symbols, and the decode is successful.
|
|
|
|
image::QRA64.png[align="center",alt="QRA64"]
|
|
|
|
=== ISCAT
|
|
|
|
ISCAT is a useful mode for signals that are weak but more or less
|
|
steady in amplitude over several seconds or longer. Aircraft scatter
|
|
at 10 GHz is a good example. ISCAT messages are free-format and may
|
|
have any length from 1 to 28 characters. This protocol includes no
|
|
error-correction facility.
|
|
|
|
=== MSK144
|
|
|
|
Meteor-scatter QSOs can be made any time on the VHF bands at distances
|
|
up to about 2100 km (1300 miles). Completing a QSO takes longer in
|
|
the evening than in the morning, longer at higher frequencies, and
|
|
longer at distances close to the upper limit. But with patience, 100
|
|
Watts or more, and a single yagi it can usually be done. The
|
|
following screen shot shows two 15-second MSK144 transmissions from
|
|
W5ADD during a 50 MHz QSO with K1JT, at a distance of about 1800 km
|
|
(1100 mi). The decoded segments have been encircled on the *Fast
|
|
Graph* spectral display.
|
|
|
|
image::MSK144.png[align="center",alt="MSK144"]
|
|
|
|
Unlike other _WSJT-X_ modes, the MSK144 decoder operates in real time
|
|
during the reception sequence. Decoded messages will appear on your
|
|
screen almost as soon as you hear them.
|
|
|
|
To configure _WSJT-X_ for MSK144 operation:
|
|
|
|
- Select *MSK144* from the *Mode* menu.
|
|
|
|
- Select *Fast* from the *Decode* menu.
|
|
|
|
- Set the audio receiving frequency to *Rx 1500 Hz*.
|
|
|
|
- Set frequency tolerance to *F Tol 100*.
|
|
|
|
- Set the *T/R* sequence duration to 15 s.
|
|
|
|
- To match decoding depth to your computer's capability, click
|
|
*Monitor* (if it's not already green) to start a receiving sequence.
|
|
Observe the percentage figure displayed on the _Receiving_ label in
|
|
the Status Bar:
|
|
|
|
image::Rx_pct_MSK144.png[align="center",alt="MSK144 Percent CPU"]
|
|
|
|
- The displayed number (here 17%) indicates the fraction of available
|
|
time being used for execution of the MSK144 real-time decoder. If
|
|
this number is well below 100% you may increase the decoding depth
|
|
from *Fast* to *Normal* or *Deep*, and increase *F Tol* from 100 to
|
|
200 Hz.
|
|
|
|
NOTE: Most modern multi-core computers can easily handle the optimum
|
|
parameters *Deep* and *F Tol 200*. Older and slower machines may not
|
|
be able to keep up at these settings; at the *Fast* and *Normal*
|
|
settings there will be a small loss in decoding capability (relative
|
|
to *Deep*) for the weakest pings.
|
|
|
|
- T/R sequences of 15 seconds or less requires selecting your
|
|
transmitted messages very quickly. Check *Auto Seq* to have the
|
|
computer make the necessary decisions automatically, based on the
|
|
messages received.
|
|
|
|
- For operation at 144 MHz or above you may find it helpful to use
|
|
short-format *Sh* messages for Tx3, Tx4, and Tx5. These messages are
|
|
20 ms long, compared with 72 ms for full-length MSK144 messages.
|
|
Their information content is a 12-bit hash of the two callsigns,
|
|
rather than the callsigns themselves, plus a 4-bit numerical report,
|
|
acknowledgment (RRR), or sign-off (73). Only the intended recipient
|
|
can decode short-messages. They will be displayed with the callsigns
|
|
enclosed in <> angle brackets, as in the following model QSO
|
|
|
|
CQ K1ABC FN42
|
|
K1ABC W9XYZ EN37
|
|
W9XYZ K1ABC +02
|
|
<K1ABC W9XYZ> R+03
|
|
<W9XYZ K1ABC> RRR
|
|
<K1ABC W9XYZ> 73
|
|
|
|
|
|
NOTE: There is little or no advantage to using MSK144 *Sh*
|
|
messages at 50 or 70 MHz. At these frequencies, most pings are long
|
|
enough to support standard messages -- which have the advantage of
|
|
being readable by anyone listening in.
|
|
|
|
=== Echo Mode
|
|
|
|
*Echo* mode allows you to make sensitive measurements of your own
|
|
lunar echoes even when they are too weak to be heard. Select *Echo*
|
|
from the *Mode* menu, aim your antenna at the moon, pick a clear
|
|
frequency, and toggle click *Tx Enable*. _WSJT-X_ will then cycle
|
|
through the following loop every 6 seconds:
|
|
|
|
1. Transmit a 1500 Hz fixed tone for 2.3 s
|
|
2. Wait about 0.2 s for start of the return echo
|
|
3. Record the received signal for 2.3 s
|
|
4. Analyze, average, and display the results
|
|
5. Repeat from step 1
|
|
|
|
To make a sequence of echo tests:
|
|
|
|
- Select *Echo* from the *Mode* menu.
|
|
|
|
- Check *Doppler tracking* and *Constant frequency on the Moon* on the
|
|
Astronomical Data window.
|
|
|
|
- Be sure that your rig control has been set up for _Split Operation_,
|
|
using either *Rig* or *Fake It* on the *Settings | Radio* tab.
|
|
|
|
- Click *Enable Tx* on the main window to start a sequence of 6-second
|
|
cycles.
|
|
|
|
- _WSJT-X_ calculates and compensates for Doppler shift automatically.
|
|
As shown in the screen shot below, when proper Doppler corrections
|
|
have been applied your return echo should always appear at the center
|
|
of the plot area on the Echo Graph window.
|
|
|
|
image::echo_144.png[align="center",alt="Echo 144 MHz"]
|
|
|
|
=== VHF+ Sample Files
|
|
|
|
Sample recordings typical of QSOs using the VHF/UHF/Microwave modes
|
|
and features of _WSJT-X_ are available for
|
|
<<DOWNLOAD_SAMPLES,download>>. New users of the VHF-and-up features
|
|
are strongly encouraged to practice decoding the signals in these
|
|
files.
|