mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-25 05:38:46 -05:00
72 lines
3.3 KiB
Plaintext
72 lines
3.3 KiB
Plaintext
// Status=edited
|
||
|
||
At the center of the main window are a number of controls used when
|
||
making QSOs. Controls not relevant to a particular mode or submode
|
||
may be "grayed out" (disabled) or removed from the display.
|
||
|
||
//.Misc Controls Center
|
||
image::misc-controls-center.png[align="center",alt="Misc Controls Center"]
|
||
|
||
* Check *Tx even/1st* to transmit in even-numbered UTC minutes or
|
||
sequences, starting at 0. Uncheck this box to transmit in the odd
|
||
sequences. The correct selection is made automatically when you
|
||
double-click on a decoded text line, as described in the
|
||
<<TUTORIAL,Basic Operating Tutorial>>.
|
||
|
||
* The Tx and Rx audio frequencies can be set automatically by
|
||
double-clicking decoded text or a signal in the waterfall. They
|
||
can also be adjusted using the spinner controls.
|
||
|
||
* You can force Tx frequency to the current Rx frequency by clicking
|
||
the *Tx<-Rx* button, and vice-versa for *Rx<-Tx*. The on-the-air
|
||
frequency of your lowest JT9 or JT65 tone is the sum of dial frequency
|
||
and audio Tx frequency.
|
||
|
||
* Check the box *Hold Tx Freq* to ensure that the specified Tx
|
||
frequency is not changed automatically when you double-click on
|
||
decoded text or a signal in the waterfall.
|
||
|
||
* For modes lacking a multi-decode feature, or when *Enable VHF/UHF/Microwave features* has been checked on the *File -> Settings -> General* tab, the *F Tol* control sets a frequency tolerance range over which decoding is attempted, centered on the Rx frequency.
|
||
|
||
* The *Report* control lets you change an automatically inserted signal report. Typical reports for the various modes fall in
|
||
the range –30 to +20 dB. Remember that JT65 reports saturate at an
|
||
upper limit of -1 dB.
|
||
|
||
+
|
||
|
||
TIP: Consider reducing power if your QSO partner reports your signal above -5 dB in one of the _WSJT-X_ slow modes. These are supposed to be weak signal modes!
|
||
|
||
* In some circumstances, especially on VHF and higher bands, you can
|
||
select a supported submode of the active mode by using the *Submode*
|
||
control. The *Sync* control sets a minimum threshold for establishing
|
||
time and frequency synchronization with a received signal.
|
||
|
||
* Spinner control *T/R xx s* sets sequence lengths for transmission
|
||
and reception in ISCAT, MSK144, and the fast JT9 modes.
|
||
|
||
* With *Split operation* activated on the *File -> Settings -> Radio* tab, in
|
||
MSK144 and the fast JT9 submodes you can activate the spinner control
|
||
*Tx CQ nnn* by checking the box to its right. The program will then
|
||
generate something like `CQ nnn K1ABC FN42` for your CQ message, where
|
||
`nnn` is the kHz portion of your current operating frequency,
|
||
in the range 010 to 999. Your CQ
|
||
message *Tx6* will then be transmitted at the calling frequency
|
||
selected in the *Tx CQ nnn* spinner control. All other messages will
|
||
be transmitted at your current operating frequency. On reception,
|
||
when you double-click on a message like `CQ nnn K1ABC FN42` your rig
|
||
will QSY to the specified frequency so you can call the station at his
|
||
specified response frequency.
|
||
|
||
* Checkboxes at bottom center of the main window control special
|
||
features for particular operating modes:
|
||
|
||
** *Sh* enables shorthand messages in JT4, JT65, QRA64 and MSK144 modes
|
||
|
||
** *Fast* enables fast JT9 submodes
|
||
|
||
** *Auto Seq* enables auto-sequencing of Tx messages
|
||
|
||
** *Call 1st* enables automatic response to the first decoded
|
||
responder to your CQ
|
||
|
||
** *Tx6* toggles between two types of shorthand messages in JT4 mode |