mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-19 10:32:02 -05:00
d9df62b9e9
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@2608 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
64 lines
3.2 KiB
Plaintext
64 lines
3.2 KiB
Plaintext
JT9 is a mode designed for amateur QSOs and beacon-like transmissions
|
|
at MF and LF. The mode uses the same 72-bit user messages as JT65.
|
|
Convolutional error-control coding (ECC) uses constraint length K=32,
|
|
rate r=1/2, and a zero tail, which leads to an encoded message length
|
|
of (72+31)*2 = 206 bits. Modulation is 9-FSK: 8 tones for data, one
|
|
for synchronization. Sixteen symbol intervals are used for
|
|
synchronization, so a transmission requires a total of 207/3 + 16 = 85
|
|
channel symbols. Symbol durations tsym are approximately
|
|
(TRperiod-10)/85, where TRperiod is the T/R sequence length in
|
|
seconds. Exact symbol lengths are chosen so that nsps, the number of
|
|
samples per symbol (at 12000 samples per second) is a number with no
|
|
prime factor greater than 7. This choice makes for efficient FFTs.
|
|
Tone spacing of the 9-FSK modulation is df=1/tsym=12000/nsps, the same
|
|
as the keying rate. The total occupied bandwidth is 9*df.
|
|
|
|
Parameters of five JT9 sub-modes are summarized in the following
|
|
table, along with S/N thresholds measured by simulation on an AWGN
|
|
(additive white Gaussian noise) channel.
|
|
|
|
-------------------------------------------------------------------------
|
|
Mode nsps nsps2 df tsym BW S/N* Tdec Tfree Factors
|
|
12000 750 (Hz) (s) (Hz) (dB) (s) (s) of nsps
|
|
-------------------------------------------------------------------------
|
|
JT9-1 6912 432 1.736 0.58 15.6 -26.9 52.5 7.5 2^8 3^3
|
|
JT9-2 15360 960 0.781 1.28 7.0 -30.2 112.3 7.7 2^10 3 5
|
|
JT9-5 40960 2560 0.293 3.41 2.6 -34.4 293.6 6.4 2^13 5
|
|
JT9-10 82944 5184 0.145 6.91 1.3 -37.5 591.0 9.0 2^10 3^4
|
|
JT9-30 250880 15750 0.048 20.91 0.4 -42.3 1788.5 11.5 2^5 3^2 5^3 7
|
|
-------------------------------------------------------------------------
|
|
* Noise power measured in a 2500 Hz bandwidth.
|
|
|
|
|
|
Transmitting
|
|
------------
|
|
1. Source encode the structured message to 72 bits
|
|
2. Apply convolutional ECC (K=32, r=1/2) to yield (72+31)*2 = 206 bits
|
|
3. Interleave to scramble the bit order
|
|
4. Assemble 3-bit groups to make (206+1)/3 = 69 symbols
|
|
5. Gray-code the symbol values
|
|
6. Insert 16 sync symbols ==> 69+15=81 channel symbols, values 0-8
|
|
|
|
|
|
Receiving
|
|
---------
|
|
1. Apply noise blanking with the timf2 method
|
|
2. Filter to 500 Hz bandwidth and downsample (1/16) to 750 Hz (FIR
|
|
filter with 61 taps). Complex data to array c0 (max 1.35M)
|
|
3. Compute symbol-length spectra at half-symbol steps. Use for
|
|
waterfall display s(15750) and save in ss(184,15750) and
|
|
savg(15750) for detecting sync vectors.
|
|
4. At time Tdec, find sync vectors in ss(); get estimates of DF, DT
|
|
5. Do full-length FFT, NFFT1=96*nsps2, zero-pad as required.
|
|
6. For each candidate signal, do inverse FFT of length 1536. This
|
|
yields 16 complex samples per symbol, and sync tone should be
|
|
close to zero frequency.
|
|
7. Use afc65b method to get improved values of DF, DT.
|
|
8. Tweak freq and time offset to 0.
|
|
9. Compute 8-bin spectra of 69 data symbols: s2(8,69). Re-order bins
|
|
by removing Gray code.
|
|
10. Compute soft symbols for 206 bits.
|
|
11. Remove interleaving
|
|
12. Pack bits into bytes, send to Fano decoder
|
|
13. If Fano succeeds, remove source encoding and display user message.
|