mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-15 16:42:12 -05:00
43664a2e01
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@3669 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
114 lines
4.6 KiB
Plaintext
114 lines
4.6 KiB
Plaintext
// Status=review
|
||
.Wide Graph Settings:
|
||
|
||
- Set *Bins/Pixel* = 7
|
||
- Adjust the width of the Wide Graph window so that the upper
|
||
frequency limit is approximately 4000 Hz.
|
||
|
||
.Main Window:
|
||
- Select *JT9+JT65* on the *Mode* menu.
|
||
- Toggle the *Tx mode* button to read *Tx JT65*, and set the Tx and Rx
|
||
frequencies to 1718 Hz.
|
||
- Double-click on *Erase* to clear both text windows.
|
||
|
||
.Open a Wave File:
|
||
|
||
- Select *File | Open* and navigate to +...\save\samples\130610_2343.wav+.
|
||
The waterfall should look like this:
|
||
|
||
//.130610_2343.wav Decode
|
||
[[X14]]
|
||
image::images/130610_2343-wav-80.png[align="left",alt="Wide Graph Decode 130610_2343"]
|
||
|
||
TIP: Notice the [blue]*BLUE* marker on the waterfall scale, here
|
||
set at 2400 Hz. Its position is set by the spinner control *JT65 nnnn
|
||
JT9*, where nnnn is a frequency in Hz. In *JT9+JT65* mode the program
|
||
will automatically decode JT65 signals below this frequency and JT9
|
||
signals above it.
|
||
|
||
JT9 signals appear in the *Cumulative* spectrum as nearly
|
||
rectangular shapes about 16 Hz wide. Although there is no clearly
|
||
visible sync tone like the one at the low-frequency edge of JT65
|
||
signals, by convention the nominal frequency of a JT9 signal is taken
|
||
to be that of its lowest tone, at the left edge of its spectrum.
|
||
|
||
This sample file contains 17 decodable signals — nine in JT65 mode
|
||
(flagged with the character # in the decoded text windows), and eight
|
||
in JT9 mode (flagged with @). The *Band Activity* window should
|
||
contain these decodes (you may need to scroll back in the window to
|
||
see them all):
|
||
|
||
// ... Figure here showing the text windows ?
|
||
[[FigDecodes]]
|
||
image::images/decodes.png[align="center"]
|
||
|
||
Since the Tx mode was set to *Tx JT65*, signals in that mode were
|
||
decoded next. If you had selected *Tx JT9*, JT9 signals would have
|
||
been decoded first.
|
||
|
||
- Confirm that mouse-click behavior is similar to that described
|
||
<<X13,earlier>>, in Example 1. The program automatically determines
|
||
the mode of each JT9 or JT65 signal.
|
||
|
||
TIP: When you double-click on a signal in the waterfall it will be
|
||
properly decoded even if on the ``wrong'' side of the *JT65 nnnn JT9*
|
||
marker. The Tx mode automatically switches to that of the decoded
|
||
signal and the Rx and Tx frequency markers on the waterfall scale
|
||
resize themselves accordingly. When selecting a JT65 signal, click on
|
||
the sync tone at its left edge.
|
||
|
||
- Double-click on the waterfall near 815 Hz: a JT65 message
|
||
originating from W7VP will be decoded and appear in the *Rx Frequency*
|
||
window.
|
||
|
||
[width="70%",cols="3,^3,^3,^4,^4,30",options="header"]
|
||
|=================================
|
||
|UTC|db|dt|Freq|Mode|Message
|
||
|2343|-7|0.3|815|#|KK4DSD W7VP -16
|
||
|=================================
|
||
|
||
- Double-click on the waterfall at 3196 Hz. The program will decode a
|
||
JT9 message from IZ0MIT:
|
||
|
||
[width="70%",cols="3,^3,^3,^4,^4,30",options="header"]
|
||
|=====================================
|
||
|UTC|db|dt|Freq|Mode|Message
|
||
|2343|-7|0.3|3196|@|WB8QPG IZ0MIT -11
|
||
|=====================================
|
||
|
||
- Scroll back in the *Band Activity* window and double-click on the
|
||
message CQ DL7ACA JO40. The program will set *Tx mode* to JT65 and Tx
|
||
and Rx frequencies to that of DL7ACA, 975 Hz. If you had checked
|
||
*Double-click on call sets Tx Enable* on the *Setup* menu, the program
|
||
would configure itself to start a QSO with DL7ACA.
|
||
|
||
- Double-click on the decoded JT65 message CQ TA4A KM37. The program
|
||
will set Tx mode to JT9 and the Rx and Tx frequencies to 3567 Hz. The
|
||
program is now configured properly for a JT9 QSO with TA4A.
|
||
|
||
.Reopen the First Sample File:
|
||
- Select *File | Open* and navigate to +...\save\samples\130418_1742.wav+.
|
||
|
||
Taking full advantage of the wide-band, dual-mode capability of
|
||
_WSJT-X_ requires a receiver bandwidth of at least 4 kHz. These
|
||
data were recorded with a much narrower Rx bandwidth, roughly 200 to
|
||
2600 Hz. If you have no Rx filter wider than about 2.7 kHz, you will
|
||
be using data like this. For best viewing, adjust *Bins/Pixel* and the
|
||
width of the Wide Graph so that only the active part of the spectrum
|
||
shows, say 0 to 2600 Hz. Re-open the example file after any change of
|
||
*Bins/Pixel* or Wide Graph width, to refresh the waterfall.
|
||
|
||
The signals in this file are all JT9 signals. To decode them
|
||
automatically in *JT9+JT65* mode you’ll need to move the *JT65 nnnn JT9*
|
||
delimiter down to 1000 Hz or less.
|
||
|
||
.Start, Zero, and Gain
|
||
|
||
Now is a good time to experiment with the *Start*, *Zero*, and *Gain*
|
||
parameters. *Start* determines the frequency displayed at the left
|
||
side of the waterfall scale. *Zero* sets the baseline level for
|
||
colors, and *Gain* sets the sensitivity for color changes. For the
|
||
receiver setup of this file good values are close to *Zero*=0,
|
||
*Gain*=0. Re-open the wave file after each change, to see the new
|
||
results.
|