WSJT-X/doc/user_guide/en/controls-functions-center.adoc
Joe Taylor 823a759f2a Another tweak for User Guuide from G3WDG.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8527 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2018-02-22 18:28:59 +00:00

80 lines
3.5 KiB
Plaintext
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// Status=review
At the center of the main window are a number of controls used when
making QSOs. Controls not relevant to a particular mode or submode
may be "grayed out" (disabled) or removed from the display.
//.Misc Controls Center
image::misc-controls-center.png[align="center",alt="Misc Controls Center"]
* Check *Tx even* to transmit in even-numbered UTC minutes or
sequences, starting at 0. Uncheck this box to transmit in the odd
sequences. The correct selection is made automatically when you
double-click on a decoded text line, as described in the
<<TUTORIAL,Basic Operating Tutorial>>.
* The Tx and Rx audio frequencies can be set automatically by
double-clicking on decoded text or a signal in the waterfall. They
can also be adjusted using the spinner controls.
* You can force Tx frequency to the current Rx frequency by clicking
the *Tx<-Rx* button, and vice-versa for *Rx<-Tx*. The on-the-air
frequency of your lowest JT9 or JT65 tone is the sum of dial frequency
and audio Tx frequency.
* Check the box *Lock Tx=Rx* to make the frequencies always track one
another.
IMPORTANT: In general we do not recommend using *Lock Tx=Rx* since it
encourages poor radio etiquette when running a frequency. With this
box checked, your own Tx frequency will move around following your
callers.
* For modes lacking a multi-decode feature, or when *Enable
VHF/UHF/Microwave features* has been checked on the *Settings ->
General* tab, the *F Tol* control sets a frequency toilerance range
over which decoding will be attempted, centered on the Rx frequency.
* The *Report* control lets you change a signal report that has been
inserted automatically. Typical reports for the various modes fall in
the range 30 to +20 dB. Remember that JT65 reports saturate at an
upper limit of -1 dB.
TIP: Consider reducing power if your QSO partner reports your
signal above -5 dB in one of the _WSJT-X_ slow modes. These are
supposed to be weak signal modes!
* In some circumstances, especially on VHF and higher bands, you can
select a supported submode of the active mode by using the *Submode*
control. The *Sync* control sets a minimum threshold for establishing
time and frequency synchronization with a received signal.
* Spinner control *T/R xx s* sets sequence lengths for transmission
and reception in ISCAT, MSK144, and the fast JT9 modes.
* With *Split operation* activated on the *Settings -> Radio* tab, in
MSK144 and the fast JT9 submodes you can activate the spinner control
*Tx CQ nnn* by checking the box to its right. The program will then
generate something like `CQ nnn K1ABC FN42` for your CQ message, where
`nnn` is the kHz portion of your current operating frequency,
in the range 010 to 999. Your CQ
message *Tx6* will then be transmitted at the calling frequency
selected in the *Tx CQ nnn* spinner control. All other messages will
be transmitted at your current operating frequency. On reception,
when you double-click on a message like `CQ nnn K1ABC FN42` your rig
will QSY to the specified frequency so you can call the station at his
specified response frequency.
* Checkboxes at bottom center of the main window control special
features for particular operating modes:
** *Sh* enables shorthand messages in JT4, JT65, QRA64 and MSK144 modes
** *Fast* enables fast JT9 submodes
** *Auto Seq* enables auto-sequencing of Tx messages
** *Call 1st* enables automatic response to the first decoded
responder to your CQ
** *Tx6* toggles between two types of shorthand messages in JT4 mode