mirror of
https://github.com/saitohirga/WSJT-X.git
synced 2024-11-15 16:42:12 -05:00
3d4cb994be
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5440 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
84 lines
3.5 KiB
Plaintext
84 lines
3.5 KiB
Plaintext
////
|
|
Questions:
|
|
Should be short one liners ending with ?::
|
|
If your question is too long for one line, consider multiple questions or rephrase
|
|
|
|
Answers:
|
|
Can be bullet or paragraphs. Bullets make for easier reading.
|
|
|
|
Bullet Usage:
|
|
* = a circle bullet single intent
|
|
** = circle bullet double indent
|
|
. = should be avoided as the questions are numbered
|
|
.. = bullet a, b, c, and so on, double indent
|
|
|
|
Alternatives: Use a * Bullet, followed by .. for example, then have
|
|
a multi-section answer using the * as the section header
|
|
|
|
* Section Header 1
|
|
.. Possible Answer a
|
|
.. Possible Answer b
|
|
* Section Header 2
|
|
.. Possible Answer a
|
|
.. Possible Answer b
|
|
|
|
Link Usage:
|
|
Use the common/links.adoc for href links to maintain consistency. Try to avoid
|
|
apostrophes ` or ' as it breaks AsciiDoc syntax without special escaping
|
|
and they do not translate into other languages well.
|
|
|
|
////
|
|
[qanda]
|
|
My displayed spectrum is flatter when I do not check the *Flatten* box. What's wrong?::
|
|
|
|
_WSJT-X_ does not expect a steep filter edge within the displayed
|
|
passband. Use a wider IF filter or reduce the displayed passband by
|
|
decreasing *Bins/Pixel*, increasing *Start*, or reducing the width of
|
|
the *Wide Graph*. You might also choose to re-center the filter
|
|
passband, if such control is available.
|
|
|
|
My rig has only a single SSB filter, about 2700 Hz bandwidth. Can I use split mode?::
|
|
|
|
Set _Split Operation_ to *Rig* (or if necessary, *Fake It*) on the
|
|
*Settings | Radio* tab. To operate primarily in the JT9 frequency
|
|
range, check the *{plus}2 kHz* box. VFO-A will be moved up by that
|
|
amount, e.g., to 14.078 MHz on 20 meters. The JT9 sub-band now falls
|
|
between about 500 Hz and 2000Hz on the waterfall display. As
|
|
described above, VFO-B will be adjusted so as to keep your Tx audio
|
|
always between 1500 and 2000 Hz. To operate JT65, simply uncheck the
|
|
*{plus}2 kHz* option. If your rig has an IF shift control or
|
|
equivalent (``passband tuning''), you can operate as if you had 4 kHz
|
|
Rx bandwidth and use the IF shift control to focus on any 2.7 kHz
|
|
portion of the JT65 and JT9 sub-bands.
|
|
|
|
How should I configure _WSJT-X_ to run multiple instances?::
|
|
|
|
Start _WSJT-X_ from a command-prompt window, passing each instance a
|
|
unique identifier as in the following two-instance example. This
|
|
procedure will isolate the *Settings* file and the writable file
|
|
location for each instance of _WSJT-X_.
|
|
|
|
wsjtx --rig-name=TS2000
|
|
wsjtx --rig-name=FT847
|
|
|
|
When setting up rig control through _OmniRig_, something goes wrong when I click *Test CAT*. What can I do about it?::
|
|
|
|
_OmniRig_ apparently has a bug that appears when you click *Test CAT*.
|
|
Forget using *Test CAT* and just click *OK*. _OmniRig_ then behaves
|
|
normally.
|
|
|
|
I am using _WSJT-X_ with _Ham Radio Deluxe_. All seems well until I start HRD Logbook or DM780 running in parallel; then CAT control becomes unreliable.::
|
|
|
|
You may see delays up to 20 seconds or so in frequency changes or
|
|
other radio commands, due to a bug in HRD. HRD folks are aware of the
|
|
problem, and are working to resolve it.
|
|
|
|
I am running _WSJT-X_ under Ubuntu 14.04. The program starts, but menu bar is missing from the top of the main window and the hot-keys don't work.::
|
|
|
|
Ubuntu's new ``Unity'' desktop puts the menu for the currently active
|
|
window at the top of the primary display screen. You can restore menu
|
|
bars to their traditional locations by typing the following in a
|
|
command-prompt window:
|
|
|
|
sudo apt-get remove appmenu-qt5
|