WSJT-X/doc/user_guide/en/vhf-features.adoc
Bill Somerville 7cda91c759 Improve the "translatability" of some of the User Guide links
To  aid translators  some of  the links  in the  doc/common/links.adoc
file, which is shared by all translations, have been changed to remove
generic  link  text  like  "here"   with  the  titles  of  the  linked
references.   Since  these  are  in the  language  of  the  references
documents there is no need to translate these.

git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6647 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2016-04-24 19:45:52 +00:00

135 lines
5.7 KiB
Plaintext

=== VHF Setup
V1.6.0 is the first _WSJT-X_ version to include features specifically
designed for use on VHF and higher bands. These features include
*JT4*, a mode particularly useful for EME on the microwave bands;
*Echo* mode, for detecting and measuring your own lunar echoes; and
automatic *Doppler tracking* for the EME path. The accuracy of
Doppler calculations is better than 1 Hz at 10 GHz. (Note that
sub-modes JT65B and JT65C are present in v1.6.0, but are not yet fully
implemented for EME purposes.)
- To activate the VHF-and-up features check the box labeled _Enable
VHF/UHF/Microwave features_ on the *Settings | General* tab.
- If you will be doing EME, check the box _Decode at t = 52 s_
to allow for the EME path delay on received signals.
- If you will use automatic Doppler tracking, check the box _Allow Tx
frequency changes while transmitting_. On the *Radio* tab select
_Split Operation_ (use either _Rig_ or _Fake It_: you might need to
experiment with both).
IMPORTANT: Not all transceivers permit computer adjustments of Tx
frequency while transmitting. Among those that do are the IC-735,
IC-756 Pro II, IC-910-H, FT-847, TS-2000 (with Rev 9 firmware
upgrade), Flex 1500 and 5000, HPSDR, Anan-10, Anan-100, and KX3.
- The main window reconfigures itself as necessary to include controls
supporting features of each mode. For example, in JT4 mode the
central part of the main window will look like this:
image::VHF_controls.png[align="center",alt="VHF Controls"]
- On the *View* menu, select *Astronomical data* to display a window
with important information for tracking the Moon and performing
automatic Doppler control. Check the box labeled _Doppler tracking_
to ensure that the right-hand portion of the window is visible.
image::Astronomical_data.png[align="center",alt="Astronomical data"]
IMPORTANT: Note that two different types of Doppler control are provided.
- Select _Full Doppler to DX Grid_ if you know your QSO partner's locator
and he/she will not be using any Doppler control.
- Select _Constant frequency on Moon_ to correct for your own (one-way)
Doppler shift to or from the Moon. If your QSO partner does the same
thing, both stations will have the required Doppler compensation.
Moreover, anyone else using this option will hear both of you
without the need for manual frequency changes. The hypothetical "`man
in the moon`" will copy all of you on the selected nominal frequency.
- In the example depicted above, the moon-based nominal frequency is
100 kHz above the stated band edge, or 10368.100 MHz for the 10 GHz
band. The home station two-way self Doppler shift is +6193 Hz, so the
one-way shift is +3096.5 Hz. Therefore, the receive frequency is set
to 10,360.103097 Hz. When a transmission is started, the frequency
is reset to 3096.5 Hz below the nominal frequency.
- Spinner controls at top right of the *Astronomical Data* window let you
set a working frequency above the nominal band edge. The frequency above
band edge is the sum of the numbers in these two controls (kHz + Hz).
=== EME with JT4
- Select *JT4* from the *Mode* menu.
- Select the desired submode, which determines the tone spacing.
Higher spacings are used on the higher microwave bands, to allow for
larger Doppler spreads. For example, JT4F is generally used for EME on
the 10 GHz band.
- If using a transverter, set the appropriate offset on the *Settings
| Frequencies* tab. Offset is defined as (desired transceiver dial
reading) minus (desired on-the-air frequency). For example, when
using a 144 MHz radio at 10368 MHz, _Offset (MHz)_ = (144 - 10368) =
-10224.000. If the band is already in the table, you can edit the
offset by double clicking on the offset field itself. Otherwise a new
band can be added by right clicking in the table and selecting _Insert_.
image::Add_station_info.png[align="center",alt="Station information"]
- The JT4 decoder in _WSJT-X_ includes optional facilities for
averaging over successive transmissions and also correlation decoding,
sometimes known as "`Deep Search`".
IMPORTANT: The *Decode* menu appears to provide options to set
different decoding behavior. However, in JT4 mode _WSJT-X_ Version
1.6 always behaves as if you have selected _Include correlation_.
image::decoding_depth.png[align="center",alt="Decoding Depth"]
- By convention, EME with JT4 can use "`short form`" messages. To
activate automatic generation of these messages, check the box labeled
_Sh_ on the main window.
IMPORTANT: Thanks to G3WDG, many additional hints for using JT4 and
Echo mode on the EME path are available in {jt4eme}.
=== Echo Mode
*Echo* mode allows you to make sensitive measurements of your own
lunar echoes, even when they are too weak to be heard. Select *Echo*
from the *Mode* menu, aim your antenna at the moon, pick a clear
frequency, and toggle click *Tx Enable*. _WSJT-X_ will then cycle
through the following loop every 6 seconds:
1. Transmit a 1500 Hz fixed tone for 2.3 s
2. Wait about 0.2 s for start of the return echo
3. Record the received signal for 2.3 s
4. Analyze, average, and display the results
5. Repeat from step 1
To make a sequence of echo tests:
- Select *Echo* from the *Mode* menu.
- On the Astronomical Data window check _Doppler tracking_ and
_Constant frequency on the Moon_
- Choose your desired test frequency using the _Frequency above nominal
band edge_ controls.
- Be sure that your rig control has been set up for _Split Operation_
(either _Rig_ of _Fake It_) on the *Settings | Radio* tab.
- Click *Enable Tx* on the main window to start a sequence of 6-second
cycles.
- _WSJT-X_ calculates and compensates for Doppler shift automatically.
Your return echo should always appear at the center of the plot area
on the Echo Graph window, as in the screen shot below.
image::echo_144.png[align="center",alt="Echo 144 MHz"]