mirror of
https://github.com/f4exb/sdrangel.git
synced 2024-11-04 16:01:14 -05:00
71 lines
2.2 KiB
Markdown
71 lines
2.2 KiB
Markdown
<h1>Android SDR Driver Input Plugin</h1>
|
|
|
|
<h2>Introduction</h2>
|
|
|
|
This input sample source plugin gets its I/Q samples from the Android [SDR Driver](https://play.google.com/store/apps/details?id=marto.rtl_tcp_andro&hl=en&gl=US) or [SDRplay Driver](https://play.google.com/store/apps/details?id=com.sdrplay.driver&hl=en&gl=US) apps.
|
|
These apps enable support for RTL SDR, HackRF and SDRPlay SDRs.
|
|
|
|
<h2>Interface</h2>
|
|
|
|
|
|
|
|
<h3>1: Start/Stop</h3>
|
|
|
|
Device start / stop button.
|
|
|
|
- Blue triangle icon: device is ready and can be started
|
|
- Green square icon: device is running and can be stopped
|
|
- Red square icon: an error has occurred with the connection to the device. The plugin will continually try to reconnect.
|
|
|
|
<h3>2: Center frequency</h3>
|
|
|
|
This is the center frequency in kHz of the device.
|
|
|
|
<h3>3: Stream sample rate</h3>
|
|
|
|
Network I/Q sample rate in kS/s.
|
|
|
|
<h3>4: Local oscillator correction</h3>
|
|
|
|
This is the correction to be applied to the device's local oscillator in ppm.
|
|
|
|
<h3>5: DC offset correction</h3>
|
|
|
|
Check this button to enable DC offset correction on the device.
|
|
|
|
<h3>6: IQ imbalance correction</h3>
|
|
|
|
Check this button to enable IQ imbalance correction on the device.
|
|
|
|
<h3>7: Bias tee</h3>
|
|
|
|
Check this button to enable a bias tee, if the device supports it.
|
|
|
|
<h3>8: Direct sampling mode</h3>
|
|
|
|
Use this button to activate RTL-SDR's direct sampling mode. This can be used to tune to HF frequencies.
|
|
|
|
<h3>9: Sample bit depth</h3>
|
|
|
|
Specifies number of bits per I/Q sample transmitted via TCP/IP. This should be 8 for RTL SDR, but can be 16 for SDRPlay.
|
|
|
|
<h3>10: Server TCP Port</h3>
|
|
|
|
TCP port of SDR Driver to connect to. Typically 1234.
|
|
|
|
<h3>11: Sample rate</h3>
|
|
|
|
Specify the device's sample rate in samples per second (S/s).
|
|
|
|
<h3>12: RF Bandwidth</h3>
|
|
|
|
Specifies the bandwidth in kHz of the analog filter in the device. Available bandwidths are dependent upon the device.
|
|
|
|
<h3>13: Gain</h3>
|
|
|
|
Specify gain in dB applied in various stages of the device. Available gains will depend upon the type of device.
|
|
|
|
<h3>12: AGC</h3>
|
|
|
|
Check to enable automatic gain control in the device. How AGC works is device dependent.
|