mirror of
https://github.com/f4exb/sdrangel.git
synced 2024-11-06 00:41:17 -05:00
97 lines
4.2 KiB
Markdown
97 lines
4.2 KiB
Markdown
<h1>BladeRF input plugin</h1>
|
|
|
|
<h2>Introduction</h2>
|
|
|
|
This input sample source plugin gets its samples from a [BladeRF device](https://www.nuand.com/).
|
|
|
|
<h2>Build</h2>
|
|
|
|
The plugin will be built only if the [BladeRF host library](https://github.com/Nuand/bladeRF) is installed in your system. If you build it from source and install it in a custom location say: `/opt/install/libbladeRF` you will have to add `-DLIBBLADERF_INCLUDE_DIR=/opt/install/libbladeRF/include -DLIBBLADERF_LIBRARIES=/opt/install/libbladeRF/lib/libbladeRF.so` to the cmake command line.
|
|
|
|
The BladeRF Host library is also provided by many Linux distributions and is built in the SDRangel binary releases.
|
|
|
|
<h2>Interface</h2>
|
|
|
|
|
|
|
|
<h3>1: Common stream parameters</h3>
|
|
|
|
|
|
|
|
<h4>1.1: Frequency</h4>
|
|
|
|
This is the center frequency of reception in kHz.
|
|
|
|
<h4>1.2: Start/Stop</h4>
|
|
|
|
Device start / stop button.
|
|
|
|
- Blue triangle icon: device is ready and can be started
|
|
- Green square icon: device is running and can be stopped
|
|
- Magenta (or pink) square icon: an error occured. In the case the device was accidentally disconnected you may click on the icon, plug back in and start again.
|
|
|
|
<h4>1.3: Record</h4>
|
|
|
|
Record baseband I/Q stream toggle button
|
|
|
|
<h4>1.4: Stream sample rate</h4>
|
|
|
|
Baseband I/Q sample rate in kS/s. This is the device sample rate (4) divided by the decimation factor (6).
|
|
|
|
<h3>2: Auto correction options</h3>
|
|
|
|
These buttons control the local DSP auto correction options:
|
|
|
|
- **DC**: auto remove DC component
|
|
- **IQ**: auto make I/Q balance
|
|
|
|
<h3>3: XB-200 add-on control</h3>
|
|
|
|
This controls the optional XB-200 add-on when it is fitted to the BladeRF main board. These controls have no effect if the XB-200 board is absent. Options are:
|
|
|
|
- **None**: XB-200 is ignored
|
|
- **Bypass**: XB-200 is passed through
|
|
- **Auto 1dB**: The 50, 144 and 220 MHz filters are switched on automatically according to the frequency of reception when it is within the -1 dB passband of the filters
|
|
- **Auto 3dB**: The 50, 144 and 220 MHz filters are switched on automatically according to the frequency of reception when it is within the -3 dB passband of the filters
|
|
- **Custom**: The signal is routed through a custom filter
|
|
- **50M**: The signal is routed through the 50 MHz filter
|
|
- **144M**: The signal is routed through the 144 MHz filter
|
|
- **222M**: The signal is routed through the 222 MHz filter
|
|
|
|
<h3>4: Device sample rate</h3>
|
|
|
|
This is the BladeRF device ADC sample rate in S/s.
|
|
|
|
Use the wheels to adjust the sample rate. Left click on a digit sets the cursor position at this digit. Right click on a digit sets all digits on the right to zero. This effectively floors value at the digit position.
|
|
|
|
<h3>5: Decimation factor</h3>
|
|
|
|
The I/Q stream from the BladeRF ADC is doensampled by a power of two before being sent to the passband. Possible values are increasing powers of two: 1 (no decimation), 2, 4, 8, 16, 32.
|
|
|
|
<h3>6: Baseband center frequency position relative the the BladeRF Rx center frequency</h3>
|
|
|
|
Possible values are:
|
|
|
|
- **Cen**: the decimation operation takes place around the BladeRF Rx center frequency
|
|
- **Inf**: the decimation operation takes place around the center of the lower half of the BladeRF Rx passband.
|
|
- **Sup**: the decimation operation takes place around the center of the upper half of the BladeRF Rx passband.
|
|
|
|
<h3>7: Rx filter bandwidth</h3>
|
|
|
|
This is the Rx filter bandwidth in kHz in the LMS6002D device. Possible values are: 1500, 1750, 2500, 2750, 3000, 3840, 5000, 5500, 6000, 7000, 8750, 10000, 12000, 14000, 20000, 28000 kHz.
|
|
|
|
<h3>8: LNA gain</h2>
|
|
|
|
This is the LNA gain in dB. LNA is inside the LMS6002D chip and is placed before the RF mixer. Possible values are:
|
|
|
|
- **0dB**: no gain
|
|
- **3dB**
|
|
- **6dB**
|
|
|
|
<h3>9: Variable gain amplifier #1 gain</h3>
|
|
|
|
The VGA1 gain can be adjusted from 5 dB to 30 dB in 1 dB steps. The VGA1 is inside the LMS6002D chip and is placed between the RF mixer and the baseband filter.
|
|
|
|
<h3>10: Variable gain amplifier #2 gain</h3>
|
|
|
|
The VGA2 gain can be adjusted from 0 dB to 30 dB in 3 dB steps. The VGA2 is inside the LMS6002D chip and is placed between the baseband filter and the ADC. |