mirror of
https://github.com/f4exb/sdrangel.git
synced 2024-11-09 01:56:05 -05:00
138 lines
4.2 KiB
Markdown
138 lines
4.2 KiB
Markdown
<h1>AM modulator plugin</h1>
|
|
|
|
<h2>Introduction</h2>
|
|
|
|
This plugin can be used to generate a narrowband amplitude modulated signal. "Narrowband" means that the bandwidth can vary from 1 to 40 kHz.
|
|
|
|
<h2>Interface</h2>
|
|
|
|
|
|
|
|
<h3>1: Frequency shift from center frequency of reception direction</h3>
|
|
|
|
The "+/-" button on the left side of the dial toggles between positive and negative shift.
|
|
|
|
<h3>2: Frequency shift from center frequency of reception value</h3>
|
|
|
|
Use the wheels to adjust the frequency shift in Hz from the center frequency of reception. Left click on a digit sets the cursor position at this digit. Right click on a digit sets all digits on the right to zero. This effectively floors value at the digit position.
|
|
|
|
<h3>3: Channel power</h3>
|
|
|
|
Average total power in dB relative to a +/- 1.0 amplitude signal generated in the pass band.
|
|
|
|
<h3>4: Channel mute</h3>
|
|
|
|
Use this button to toggle mute for this channel.
|
|
|
|
<h3>5: RF bandwidth</h3>
|
|
|
|
This is the bandwidth in kHz of the channel signal filtered after modulation. It can be set continuously in 1 kHz steps from 1 to 40 kHz.
|
|
|
|
<h3>6: Modulation level</h3>
|
|
|
|
Adjusts the AM modulation level in %
|
|
|
|
<h3>7: Volume</h3>
|
|
|
|
This is the volume of the audio signal from 0.0 (mute) to 2.0 (maximum). It can be varied continuously in 0.1 steps using the dial button.
|
|
|
|
<h3>8: Level meter in %</h3>
|
|
|
|
- top bar (beige): average value
|
|
- bottom bar (brown): instantaneous peak value
|
|
- tip vertical bar (bright red): peak hold value
|
|
|
|
You should aim at keepimg the peak value below 100% using the volume control
|
|
|
|
<h3>9: Input source control</h3>
|
|
|
|
|
|
|
|
<h4>9.1: Tone input select</h4>
|
|
|
|
Switches to the tone input. You must switch it off to make other inputs available.
|
|
|
|
<h4>9.2: Morse keyer input select</h4>
|
|
|
|
Switches to the Morse keyer input. You must switch it off to make other inputs available.
|
|
|
|
<h4>9.3: Tone frequency (kHz)</h4>
|
|
|
|
Adjusts the tone frequency from 0.1 to 2.5 kHz in 0.01 kHz steps
|
|
|
|
<h4>9.4: Audio input select</h4>
|
|
|
|
Switches to the audio input. You must switch it off to make other inputs available.
|
|
|
|
<h3>10: CW (Morse) text</h3>
|
|
|
|
Enter the text to be keyed when Morse input is active and in text mode
|
|
|
|
<h3>11: Clear CW text</h3>
|
|
|
|
Clears the CW (Morse) text
|
|
|
|
<h3>12: Morse keyer controls</h3>
|
|
|
|
|
|
|
|
<h4>12.1: CW keying speed</h4>
|
|
|
|
Sets the CW speed in Words Per Minute (WPM). This is based on the word "PARIS" sent 5 times. For 5 WPM the dot length is 240 ms. In other terms the dot length is calculated as 1.2 / WPM seconds. The dot length is used as the base to compute other timings:
|
|
|
|
- Element (dot or dash) silence separator: 1 dot length
|
|
- Dash: 3 dot lengths
|
|
- Character silence separator: 3 dot lengths
|
|
- Word silence separator: 7 dot lengths
|
|
|
|
<h4>12.2: Dots keying</h4>
|
|
|
|
Switch this button to send dots continuously
|
|
|
|
<h4>12.3: Dashes keying</h4>
|
|
|
|
Switch this button to send dashes continuously
|
|
|
|
<h4>12.4: Text keying</h4>
|
|
|
|
Switch this button to send the text typed into the text box (10)
|
|
|
|
<h4>12.5: Text auto repeat</h4>
|
|
|
|
Switch this button to auto repeat the text keying
|
|
|
|
<h4>12.6: Text play/stop</h4>
|
|
|
|
Use this button to stop sending text. When resuming keying restarts at the start of text
|
|
|
|
<h3>13: Audio file path</h3>
|
|
|
|
The path to the selected audio file to be played or dots if unselected
|
|
|
|
<h3>14: Audio file play controls</h3>
|
|
|
|
|
|
|
|
<h4>14.1: Audio file select</h4>
|
|
|
|
Opens a file dialog to select the audio file to be played. It must be mono 48 kHz 16LE raw format.
|
|
|
|
<h4>14.2: Audio file loop</h4>
|
|
|
|
Audio replay file at the end
|
|
|
|
<h4>14.3: Play/pause file play</h4>
|
|
|
|
Toggle play/pause file play. When paused the slider below (17) can be used to randomly set the position in the file when re-starting.
|
|
|
|
<h3>15: Play file current position</h3>
|
|
|
|
This is the current audio file play position in time units relative to the start
|
|
|
|
<h3>16: Play file length</h3>
|
|
|
|
This is the audio file play length in time units
|
|
|
|
<h3>17: Play file position slider</h3>
|
|
|
|
This slider can be used to randomly set the currennt position in the file when file play is in pause state (button 14.3) |