android_device_xiaomi_sm8350-common/wifi/WCNSS_qcom_cfg.ini

# This file allows user to override the factory
# defaults for the WLAN Driver

fw_timeout_crash=1
gDot11Mode=0
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
gAddTSWhenACMIsOff=1
gEnableApOBSSProt=1
RTSThreshold=1048576
gDisableIntraBssFwd=0
g11dSupportEnabled=0
gEnableDFSMasterCap=1
gNeighborScanTimerPeriod=200
gNeighborLookupThreshold=76
gNeighborScanChannelMinTime=20
FastRoamEnabled=1
RoamRssiDiff=5
gRoamIntraBand=0
gChannelBondingMode5GHz=1
gEnableDFSChnlScan=1
gAllowDFSChannelRoam=1
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1
gActiveMaxChannelTime=40
gWlanMccToSccSwitchMode = 3
gEnableTXSTBC=1
gEnableTxBFeeSAP=1
gEnableTxBFin20MHz=1
gEnableTxSUBeamformer=1
gRrmEnable=1
gEnablefwprint=0
gEnablefwlog=1
gVhtAmpduLenExponent=7
gVhtMpduLen=2
isP2pDeviceAddrAdministrated=0
gEnableVhtFor24GHzBand=1
gEnableLpassSupport=1
gCountryCodePriority=1
gEnableMuBformee=1
gEnableTDLSSupport=1
gEnableTDLSImplicitTrigger=1
gTDLSExternalControl=1
gEnableTDLSOffChannel=1

################ Datapath feature set Begin ################
gBusBandwidthHighThreshold=2000
gBusBandwidthMediumThreshold=500
gBusBandwidthLowThreshold=150
gBusBandwidthComputeInterval=100
gVhtRxMCS=2
gVhtTxMCS=2
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2
gIPAConfig=0x7d
gIPADescSize=800
dp_tx_ring_size=3072
gReorderOffloadSupported=1
gCEClassifyEnable=1
rx_mode=20
gEnableFastPath=1
gEnableIpTcpUdpChecksumOffload=1
TSOEnable=1
GROEnable=1
ght_mpdu_density=4
gEnableFlowSteering=1
ce_service_max_yield_time=500
ce_service_max_rx_ind_flush=1
maxMSDUsPerRxInd=8
#gEnableNUDTracking=1
dp_rx_fisa_enable=1
dp_rx_flow_search_table_size=128
rpsRxQueueCpuMapList=f3
legacy_mode_csum_disable=1

################ Datapath feature set End ################

adaptive_dwell_mode_enabled=1
hostscan_adaptive_dwell_mode=1
adapt_dwell_lpf_weight=80
adapt_dwell_wifi_act_threshold=10
enable_rtt_mac_randomization=1
gEnableSNRMonitoring=1
gWmiCreditCount=1
acs_with_more_param=1
AutoChannelSelectWeight=0x00fafafa
bcast_twt=1
gRuntimePM=2
gRuntimePMDelay=500
gEnablePacketLog=0
gfine_time_meas_cap=0x0030D
oem_6g_support_disable=0
cfr_disable=7

active_max_channel_time_2g=80
gActiveMaxChannelTime=60
active_max_channel_time_6g=60
gPassiveMaxChannelTime=110
passive_max_channel_time_6g=60

#####################################Xiaomi ADD: START

# WLM flags setting for ultralow level, bit9 for BMPS disabled
# bit 0: Avoid scan request from HLOS if setting
# bit 1: Skip DFS channel SCAN if setting
# bit 19/20: 1 to set PCIE in L1SS state(low power mode), 0 to set PCIE in L0 state(active mode)
wlm_latency_flags_ultralow=0x180003

#APF: Android Packet Filter
gActiveMcBcBpfMode=1

# Assoc failure timeout value
# Code default is 2000
assoc_failure_timeout=5000

# Enable NUD tracking feature
# 0 - disable(default),1 - trigger disconnect, 2 - trigger roaming,
# 3 - trigger roaming, but if roam fails, disconnection
gEnableNUDTracking=3

#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
#are succeed to send or not. Hence total effective detection time is
# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
gGoKeepAlivePeriod = 20
gApKeepAlivePeriod = 20
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod = 30

# Enable ETSI SRD channels by Xiaomi. Qualcom default value is disable
# * BIT 0:- Enable/Disable SRD channels for SAP.
# * BIT 1:- Enable/Disable SRD channels for P2P-GO.
# * BIT 2:- Enable/Disable SRD channels for NAN.
# Code default value is 6.
etsi13_srd_chan_in_master_mode=7

#####Roaming
# Sets RSSI preference for 5GHz over 2.4GHz AP
gSelect5GHzMargin=5

# Candidate AP minimum RSSI for beacon miss roam trigger
# Code default is -70
candidate_min_rssi_for_beacon_miss=-83

# Dense traffic threshold in kBps
# Code default is 400
gtraffic_threshold=50

#Idle Monitor Roaming: START
# Code default is flase to disable idle roaming
enable_idle_roam=1
idle_roam_min_rssi=-65
#Idle Monitor Roaming: END

#enable/disable FT open feature
# Code default is 1
enable_ftopen=0

# Stop auto-creating twt session
twt_congestion_timeout=0

#VTS SAR test fail as sar version is not match
gEnableSARV1toSARV2=1

# This ini is used to give higher priority for 5g scc than dbs.
# It is bitmap per enum policy_mgr_con_mode.
# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
g_prefer_5g_scc_to_dbs=8

# set modulated DTIM interval
gEnableModulatedDTIM=3
gMaxLIModulatedDTIM=3

# Reduce the expiry time for avoid list and black list in drv.
avoid_list_expiry_time=3
black_list_expiry_time=5
# Improve threshold to move the Ap from avoid to blacklist
bad_bssid_counter_thresh=7

# Enable the sending of ICMP requests to the
# FW at an interval of 200 milliseconds
send_icmp_req_to_fw=200

# Enable SoftAP on indoor channel, but Xiaomi's patch in driver only
# allow this when STA was connected on the same indoor channel.
gindoor_channel_support=1

#Enable max link speed
gReportMaxLinkSpeed=2

#####################################Xiaomi ADD: END


# MIUI:ADD:
# Add for optimize download performance in noisy env.

# used to specify AP OUIs. The station's EDCA should follow
# the APs' when connecting to those AP, even if the
# gEnableEdcaParams is set.
# Huawei OUI:ac:85:3d
gActionOUIDisableAggressiveEDCA=ac853d 00 01
# Enable edca parameter
gEnableEdcaParams=1
gEdcaVoCwmin=2
gEdcaViCwmin=2
gEdcaBkCwmin=2
gEdcaBeCwmin=2

gEdcaVoCwmax=3
gEdcaViCwmax=3
gEdcaBkCwmax=3
gEdcaBeCwmax=3

gEdcaVoAifs=2
gEdcaViAifs=2
gEdcaBkAifs=2
gEdcaBeAifs=2

END

# Note: Configuration parser would not read anything past the END marker