sm8350-common: update wifi configs

This commit is contained in:
Cosmin Tanislav 2021-09-05 12:28:47 +03:00
parent 69272b9f09
commit 1d0e2e3c57
2 changed files with 187 additions and 483 deletions

View File

@ -1,143 +1,125 @@
# This file allows user to override the factory
# defaults for the WLAN Driver
# Enable IMPS or not
gEnableImps=1
# Enable BMPS or not
gEnableBmps=1
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only.
fw_timeout_crash=1
gDot11Mode=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# UAPSD service interval for VO,VI, BE, BK traffic
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Flags to filter Mcast and Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=3
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#Flag to enable HostNSOffload feature or not
hostNSOffload=1
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2346
# Intra-BSS forward
RTSThreshold=1048576
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=0
# 802.11h support
g11hSupportEnabled=1
# DFS Master Capability
gEnableDFSMasterCap=1
# ESE Support and fast transition
EseEnabled=0
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
gNeighborLookupThreshold=76
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
# Check if the AP to which we are roaming is better than current AP in
# terms of RSSI. Checking is disabled if set to Zero.Otherwise it will
# use this value as to how better the RSSI of the new/roamable AP should
# be for roaming
RoamRssiDiff=5
# To enable, set gRoamIntraBand=1 (Roaming within band)
# To disable, set gRoamIntraBand=0 (Roaming across band)
gRoamIntraBand=0
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
gWlanAutoShutdown = 0
# Not used.
gApAutoChannelSelection=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=0
#Channel Bonding
gChannelBondingMode5GHz=1
gEnableDFSChnlScan=1
gAllowDFSChannelRoam=1
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1
gActiveMaxChannelTime=40
gWlanMccToSccSwitchMode = 3
gEnableTXSTBC=1
gEnableTxBFeeSAP=1
gEnableTxBFin20MHz=1
gEnableTxSUBeamformer=1
gRrmEnable=1
gEnablefwprint=0
gEnablefwlog=1
gVhtAmpduLenExponent=7
gVhtMpduLen=2
isP2pDeviceAddrAdministrated=0
gEnableVhtFor24GHzBand=1
gEnableLpassSupport=1
gCountryCodePriority=1
gEnableMuBformee=1
gEnableTDLSSupport=1
gEnableTDLSImplicitTrigger=1
gTDLSExternalControl=1
gEnableTDLSOffChannel=1
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
#is idle for last 10 seconds.) For both active and power save clients.
################ Datapath feature set Begin ################
gBusBandwidthHighThreshold=2000
gBusBandwidthMediumThreshold=500
gBusBandwidthLowThreshold=150
gBusBandwidthComputeInterval=100
gVhtRxMCS=2
gVhtTxMCS=2
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2
gIPAConfig=0x7d
gIPADescSize=800
dp_tx_ring_size=3072
gReorderOffloadSupported=1
gCEClassifyEnable=1
rx_mode=20
gEnableFastPath=1
gEnableIpTcpUdpChecksumOffload=1
TSOEnable=1
GROEnable=1
ght_mpdu_density=4
gEnableFlowSteering=1
ce_service_max_yield_time=500
ce_service_max_rx_ind_flush=1
maxMSDUsPerRxInd=8
#gEnableNUDTracking=1
dp_rx_fisa_enable=1
dp_rx_flow_search_table_size=128
rpsRxQueueCpuMapList=f3
legacy_mode_csum_disable=1
#Power save clients: DUT set TIM bit from 10th second onwards and till client
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
################ Datapath feature set End ################
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
#success still we try on 11th second if not tries on 12th and so on till 15th
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
#case DUT will detect client got removed in (10+5) seconds.
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
adaptive_dwell_mode_enabled=1
hostscan_adaptive_dwell_mode=1
adapt_dwell_lpf_weight=80
adapt_dwell_wifi_act_threshold=10
enable_rtt_mac_randomization=1
gEnableSNRMonitoring=1
gWmiCreditCount=1
acs_with_more_param=1
AutoChannelSelectWeight=0x00fafafa
bcast_twt=1
gRuntimePM=2
gRuntimePMDelay=500
gEnablePacketLog=0
gfine_time_meas_cap=0x0030D
oem_6g_support_disable=0
cfr_disable=7
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
#it is period where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
active_max_channel_time_2g=80
gActiveMaxChannelTime=60
active_max_channel_time_6g=60
gPassiveMaxChannelTime=110
passive_max_channel_time_6g=60
#####################################Xiaomi ADD: START
# WLM flags setting for ultralow level, bit9 for BMPS disabled
# bit 0: Avoid scan request from HLOS if setting
# bit 1: Skip DFS channel SCAN if setting
# bit 19/20: 1 to set PCIE in L1SS state(low power mode), 0 to set PCIE in L0 state(active mode)
wlm_latency_flags_ultralow=0x180003
#APF: Android Packet Filter
gActiveMcBcBpfMode=1
# Assoc failure timeout value
# Code default is 2000
assoc_failure_timeout=5000
# Enable NUD tracking feature
# 0 - disable(default),1 - trigger disconnect, 2 - trigger roaming,
# 3 - trigger roaming, but if roam fails, disconnection
gEnableNUDTracking=3
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
#are succeed to send or not. Hence total effective detection time is
@ -145,377 +127,98 @@ gChannelBondingMode5GHz=1
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
gGoKeepAlivePeriod = 20
gApKeepAlivePeriod = 20
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
# Enable DFS channel roam
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
gAllowDFSChannelRoam=1
gVhtChannelWidth=2
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200
# Set txchainmask and rxchainmask
# These parameters are used only if gEnable2x2 is 0
# Valid values are 1,2
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
gActiveMaxChannelTime=40
gActiveMinChannelTime=20
#If set to 0, MCC is not allowed.
gEnableMCCMode=1
# MCC to SCC Switch mode:
# 0-Disable
# 1-Enable
# 2-Force SCC if same band, with SAP restart
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
# without SAP restart by sending (E)CSA
gWlanMccToSccSwitchMode = 3
# 1=enable STBC; 0=disable STBC
gEnableRXSTBC=1
# 1=enable tx STBC; 0=disable
gEnableTXSTBC=1
# 1=enable rx LDPC; 0=disable
gEnableRXLDPC=1
#Enable/Disable Tx beamforming
gTxBFEnable=1
#Enable/Disable Tx beamformee in SAP mode
gEnableTxBFeeSAP=1
# Enable Tx beamforming in VHT20MHz
# Valid values are 0,1. If commented out, the default value is 0.
# 0=disable, 1=enable
gEnableTxBFin20MHz=1
#Enable/Disable SU Tx beamformer support.
gEnableTxSUBeamformer=1
gEnableFastRoamInConcurrency=1
#Maxium Channel time in msec
gMaxMediumTime = 6000
# 802.11K support
gRrmEnable=1
#Enable Power Save offload
gEnablePowerSaveOffload=1
#Enable firmware uart print
gEnablefwprint=0
# Firmware log mode
# Valid values are 0,1,2
# 0=Disable, 1=WMI, 2=DIAG
gEnablefwlog=1
# Maximum Receive AMPDU size (VHT only. Valid values:
# 0->8k 1->16k 2->32k 3->64k 4->128k)
gVhtAmpduLenExponent=7
# Maximum MPDU length (VHT only. Valid values:
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
gVhtMpduLen=2
# Maximum number of wow filters required
#gMaxWoWFilters=22
# WOW Enable/Disable.
# 0 - Disable both magic pattern match and pattern byte match.
# 1 - Enable magic pattern match on all interfaces.
# 2 - Enable pattern byte match on all interfaces.
# 3 - Enable both magic pattern and pattern byte match on all interfaces.
# Default value of gEnableWoW is 3.
# gEnableWoW=0
# Enable or Disable MCC Adaptive Scheduler at the FW
# 1=Enable (default), 0=Disable
gEnableMCCAdaptiveScheduler=1
#Enable or Disable p2p device address administered
isP2pDeviceAddrAdministrated=0
# Set Thermal Power limit
TxPower2g=10
TxPower5g=10
# Remove Overlap channel restriction
gEnableOverLapCh=0
#Enable VHT on 2.4Ghz
gEnableVhtFor24GHzBand=1
# Configure channel Bonding in 2.4GHz
gChannelBondingMode24GHz=0
#Maximum number of offload peers supported
# gMaxOffloadPeers=2
# controlling the following offload patterns
# through ini parameter. Default value is 1
# to disable set it to zero. ssdp = 0
# Setup multicast pattern for mDNS 224.0.0.251,
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
ssdp=0
#Enable Memory Deep Sleep
gEnableMemDeepSleep=1
# Regulatory Setting; 0=STRICT; 1=CUSTOM
gRegulatoryChangeCountry=1
# RA filtering rate limit param, the current value would not
# help if the lifetime in RA is less than 3*60=3min. Then
# we need to change it, though it is uncommon.
# gRAFilterEnable=0
gRArateLimitInterval=600
# Maximum number of concurrent connections
gMaxConcurrentActiveSessions=3
# Disable/Enable GreenAP
# 0 to disable, 1 to enable, default: 1
gEnableGreenAp=0
# Radar PRI multiplier
gDFSradarMappingPriMultiplier=4
gPNOScanSupport=1
#Enable/Disable LPASS support
# 0 to disable, 1 to enable
gEnableLpassSupport=1
# Whether userspace country code setting shld have priority
gCountryCodePriority=1
# Enable(1)/Disable(0) SIFS burst
gEnableSifsBurst=1
# Enable or Disable Multi-user MIMO
# 1=Enable (default), 0=Disable
gEnableMuBformee=1
# Enable/Disable channel avoidance for SAP in SCC scenario
# 0 - disable
# 1 - enable
gSapSccChanAvoidance=0
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
gIbssTxSpEndInactivityTime=10
# Enable support for TDLS
# 0 - disable
# 1 - enable
gEnableTDLSSupport=1
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
# and RSSI) is met and then will initiate teardown when teardown criteria
# (idle packet count and RSSI) is met.
# 0 - disable
# 1 - enable
gEnableTDLSImplicitTrigger=1
# Enable TDLS External Control. That is, user space application has to
# first configure a peer MAC in wlan driver towards which TDLS is desired.
# Device will establish TDLS only towards those configured peers whenever
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
# when teardown criteria (idle packet count and RSSI) is met. However,
# device will accept TDLS connection if it is initiated from any other peer,
# even if that peer is not configured.
# 0 - disable
# 1 - enable
# For TDLS External Control, Implicit Trigger must also be enabled.
gTDLSExternalControl=1
# Enable support for TDLS off-channel operation
# 0 - disable
# 1 - enable
# TDLS off-channel operation will be invoked when there is only one
# TDLS connection.
gEnableTDLSOffChannel=1
# Enable or Disable Random MAC (Spoofing)
# 1=Enable (default), 0=Disable
gEnableMacAddrSpoof=1
################ Datapath feature set Begin ################
# Bus bandwidth threshold values in terms of number of packets
gBusBandwidthHighThreshold=2000
gBusBandwidthMediumThreshold=500
gBusBandwidthLowThreshold=150
# Bus bandwidth compute timeout value in ms
gBusBandwidthComputeInterval=100
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# VHT Tx/Rx MCS values for 2x2
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2
#IPA config is a bit mask and following are the configurations.
#bit0 IPA Enable
#bit1 IPA PRE Filter enable
#bit2 IPv6 enable
#bit3 IPA Resource Manager (RM) enable
#bit4 IPA Clock scaling enable
#bit5 IPA uC ENABLE
#bit6 IPA uC STA ENABLE
#bit8 IPA Real Time Debugging
gIPAConfig=0x7d
gIPADescSize=800
# Enable/Disable RX full reorder offload
gReorderOffloadSupported=1
# Enable CE classification
# 1 - enable(default) 0 - disable
gCEClassifyEnable=1
# Enable Rx handling options
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
rx_mode=5
# Enable(Tx) fastpath for data traffic.
# 1 - enable(default) 0 - disable
gEnableFastPath=1
# This flag enables IP, TCP and UDP checksum offload
# 1 - enable(default) 0 - disable
gEnableIpTcpUdpChecksumOffload=1
# Enable TCP Segmentation Offload
# 1 - enable 0 - disable
TSOEnable=1
# Enable Generic Receive Offload
# 1 - enable(default) 0 - disable
GROEnable=1
# Enable HT MPDU Density
# 4 for 2 micro sec
ght_mpdu_density=4
# Enable flow steering to enable multiple CEs for Rx flows.
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
# Parallel Rx paths.
# 1 - enable 0 - disable(default)
gEnableFlowSteering=1
# Time in microseconds after which a NAPI poll must yield
ce_service_max_yield_time=500
#Maximum number of HTT messages to be processed per NAPI poll
ce_service_max_rx_ind_flush=1
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
maxMSDUsPerRxInd=8
# Enable NUD tracking feature
# 1 - enable 0 - disable(default)
gEnableNUDTracking=1
# Enable PEER UNMAP CONF SUPPORT
# 1 - enable 0 - disable(default)
gEnablePeerUnmapConfSupport=1
################ Datapath feature set End ################
################ NAN feature set start ###################
# Enable NAN discovery (NAN 1.0)
# 1 - enable 0 - disable(default)
gEnableNanSupport=1
# Enable NAN Datapath
genable_nan_datapath=1
################ NAN feature set end #####################
adaptive_dwell_mode_enabled=1
hostscan_adaptive_dwell_mode=1
adapt_dwell_lpf_weight=80
adapt_dwell_wifi_act_threshold=10
MAWCEnabled=0
drop_bcn_on_chan_mismatch=0
# Enable/Disable rtt sta mac randomization
enable_rtt_mac_randomization=1
#Enable/Disable SNR monitoring
gEnableSNRMonitoring=1
#Sets RSSI preference for 5GHz over 2.4GHz AP
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod = 30
# Enable ETSI SRD channels by Xiaomi. Qualcom default value is disable
# * BIT 0:- Enable/Disable SRD channels for SAP.
# * BIT 1:- Enable/Disable SRD channels for P2P-GO.
# * BIT 2:- Enable/Disable SRD channels for NAN.
# Code default value is 6.
etsi13_srd_chan_in_master_mode=7
#####Roaming
# Sets RSSI preference for 5GHz over 2.4GHz AP
gSelect5GHzMargin=5
#RSSI threshold offset for 2G to 5G roam
roam_bad_rssi_thresh_offset_2g=0
#RSSI threshold for background roam
roam_bg_scan_bad_rssi_thresh=-76
#Sends NULL frame to AP periodically in seconds to notify STA's existence
gStaKeepAlivePeriod=30
gEnablePacketLog=1
#Enable/Disable Modulated DTIM feature
gEnableModulatedDTIM=3
#Set MaxLIModulate Dtim
gMaxLIModulatedDTIM=3
#Sets dense roam RSSI Threshold diff
groam_dense_rssi_thresh_offset=5
#traffic Threshold required for dense roam scan
# Candidate AP minimum RSSI for beacon miss roam trigger
# Code default is -70
candidate_min_rssi_for_beacon_miss=-83
# Dense traffic threshold in kBps
# Code default is 400
gtraffic_threshold=50
gRoamBmissFirstBcnt=10
gRoamBmissFinalBcnt=20
#To Enable/Disable PER based Roaming in FW
gper_roam_enabled=3
#ARP access category
arp_ac_category=0
#Enable/Disable LPRx
gEnableLPRx=0
gEnableSelfRecovery=1
#Enable/Disable FT open feature
#Idle Monitor Roaming: START
# Code default is flase to disable idle roaming
enable_idle_roam=1
idle_roam_min_rssi=-65
#Idle Monitor Roaming: END
#enable/disable FT open feature
# Code default is 1
enable_ftopen=0
# Stop auto-creating twt session
twt_congestion_timeout=0
#VTS SAR test fail as sar version is not match
gEnableSARV1toSARV2=1
# This ini is used to give higher priority for 5g scc than dbs.
# It is bitmap per enum policy_mgr_con_mode.
# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
g_prefer_5g_scc_to_dbs=8
# set modulated DTIM interval
gEnableModulatedDTIM=3
gMaxLIModulatedDTIM=3
# Reduce the expiry time for avoid list and black list in drv.
avoid_list_expiry_time=3
black_list_expiry_time=5
# Improve threshold to move the Ap from avoid to blacklist
bad_bssid_counter_thresh=7
# Enable the sending of ICMP requests to the
# FW at an interval of 200 milliseconds
send_icmp_req_to_fw=200
# Enable SoftAP on indoor channel, but Xiaomi's patch in driver only
# allow this when STA was connected on the same indoor channel.
gindoor_channel_support=1
#Enable max link speed
gReportMaxLinkSpeed=2
#Enable/Disable SAE support in Driver
sae_enabled=0
# Enable/disable ETSI SRD channels in master mode PCL and ACS functionality
etsi13_srd_chan_in_master_mode=1
# Set max time for active 2G channel scan
active_max_channel_time_2g=0
# Enable/Disable emergency roaming during deauth/disassoc
enable_disconnect_roam_offload=1
# Enable/Disable RTT feature
gEnableRTTSupport=0
#####################################Xiaomi ADD: END
# MIUI:ADD:
# Add for optimize download performance in noisy env.
# used to specify AP OUIs. The station's EDCA should follow
# the APs' when connecting to those AP, even if the
# gEnableEdcaParams is set.
# Huawei OUI:ac:85:3d
gActionOUIDisableAggressiveEDCA=ac853d 00 01
# Enable edca parameter
gEnableEdcaParams=1
gEdcaVoCwmin=2
gEdcaViCwmin=2
gEdcaBkCwmin=2
gEdcaBeCwmin=2
gEdcaVoCwmax=3
gEdcaViCwmax=3
gEdcaBkCwmax=3
gEdcaBeCwmax=3
gEdcaVoAifs=2
gEdcaViAifs=2
gEdcaBkAifs=2
gEdcaBeAifs=2
END

View File

@ -2,4 +2,5 @@ disable_scan_offload=1
p2p_no_group_iface=1
persistent_reconnect=1
bss_max_count=400
p2p_go_intent=14
p2p_go_he=1
p2p_6ghz_disable=1