The original code would incorrectly hardcode ELS timeout values
rather than using the traditional '2 * r_a_tov' value. In some
cases, the hardcoded values would be larger than the
mailbox-command-timeout and result in a needless BIG_HAMMER (ISP
reset), the typical recovery mechanism employed in such cases.
The second defect in the original code was in the assignment of
the default 'ha->r_a_tov' to twice the traditional value.
Correct this by setting the value to 10 seconds.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For recent ISPs, software must detect OVERRUN conditions by
checking the SS_RESIDUAL_OVER bit during CS_COMPLETE handling.
Update the driver to perform this check, which is consistent with
what earlier firmwares did by explicitly cracking open the
FCP_RSP statuses and returning an CS_DATA_OVERRUN.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no point in hitting the RISC with what will most
assuredly be an unsucessful reset of the RISC hardware if the
initial stop-firmware mailbox command fails with a time-out
status. Instead, to avoid what could amount to a lengthy
stop-firmware/detect-failure/reset-risc loop, continue with
driver unloading and discard the stop-firmware requirement.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fix up from Daniel Drake for replacing GFP_DMA with something
more sensible has gone in here:
commit 69e562c234
Author: Daniel Drake <dsd@gentoo.org>
Date: Wed Feb 20 13:29:05 2008 +0000
[SCSI] arcmsr: fix message allocation
add a change log and update the version for this.
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ps3rom does:
scsi_for_each_sg(cmd, sgpnt, scsi_sg_count(cmd), k) {
kaddr = kmap_atomic(sg_page(sgpnt), KM_IRQ0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sg driver rounds up the length in struct scatterlist to be a multiple
of 512 in some conditions. So LLDs can't use the data length in a sg
list to calculate residual. Instead, the length in struct scsi_cmnd
should be used.
[Geert: the variable buflen already contains scsi_bufflen(cmd)]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The phy sas address is showing wrongly (wrong endianness). Fix up the
endian transforms to make this correct.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recent patch named:
[SCSI] gdth: !use_sg cleanup and use of scsi accessors
has done a bad job in handling internal commands issued by gdth_execute().
Internal commands are issued with device gdth_cmd_str ready made directly
to the card, without any mapping or translations of scsi commands. So here
I added a gdth_cmd_str pointer to the gdth_cmndinfo private structure which
is then copied directly to host.
following this patch is a cleanup that removes the home cooked accessors
and reverts them to regular scsi_cmnd accessors. Since they are not used
anymore. After review maybe the 2 patches should be squashed together.
FIXME: There is still a problem with gdth_get_info(). as reported there
is a WARN_ON trigerd in dma_free_coherent() when doing:
$ cat /proc/sys/gdth/0
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gdth_exit would first remove all cards then stop the timer
and would not sync with the timer function. This caused a crash
in gdth_timer() when module was unloaded.
So del_timer_sync the timer before we delete the cards.
also the reboot notifier function would crash. So clean
that up and fix the crashes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The old tools did not set max session cmds. This is a regression.
I removed the check when merging the power of 2 patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a particularly nasty bug. The problem is that if any internal
ascb times out, currently we free it even though it's pending at the
sequencer. This results in the sequencer getting terminally confused
and the error message:
BUG:sequencer:dl:no ascb
Being returned when it comes back. The way to fix this is to manage
freeing the ascb from the tasklet completion routine, so that we only
free it when the sequencer actually returns it. The code is also
altered to use on stack completions and transfer variables.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Once the phy reset is plumbed in properly, SATA error handling fails
nastily because we change the port attached_sas_address using the WWN
field of the IDENTIFY message. This is a nice thing to do in theory,
but it really destroys hotplug because any event on the port causes an
automatic mismatch between the sas_address the phy just picked up and
the one we propagate into the port. However ugly they are, we have to
stick with the sas addresses made up by the phys and expanders.
Also does a few cosmetic changes to the way port printing is done to
make it clearer how a port is formed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently aic94xx has no exported I_T_nexus_reset function. This is a
bit of a huge problem, since sas_ata relies on this function to
perform an ATA phy reset and also it means that if abort fails, we
really have no bigger hammer to hit everything with.
Plumb in the I_T_nexus_reset by quiescing the sequencer, sending the
correct phy reset (link for ATA and hard for SAS) and then carefully
resuming the sequencer again.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
mvsas.c picked up execute permissions. Move it back to being a plane
old file.
James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Oleg Nesterov and others have pointed out that on some architectures,
the traditional sequence of
set_current_state(TASK_INTERRUPTIBLE);
if (CONDITION)
return;
schedule();
is racy wrt another CPU doing
CONDITION = 1;
wake_up_process(p);
because while set_current_state() has a memory barrier separating
setting of the TASK_INTERRUPTIBLE state from reading of the CONDITION
variable, there is no such memory barrier on the wakeup side.
Now, wake_up_process() does actually take a spinlock before it reads and
sets the task state on the waking side, and on x86 (and many other
architectures) that spinlock is in fact equivalent to a memory barrier,
but that is not generally guaranteed. The write that sets CONDITION
could move into the critical region protected by the runqueue spinlock.
However, adding a smp_wmb() to before the spinlock should now order the
writing of CONDITION wrt the lock itself, which in turn is ordered wrt
the accesses within the spinlock (which includes the reading of the old
state).
This should thus close the race (which probably has never been seen in
practice, but since smp_wmb() is a no-op on x86, it's not like this will
make anything worse either on the most common architecture where the
spinlock already gave the required protection).
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(sorry for being offtpoic, but while experts are here...)
A "typical" implementation of atomic_add_unless() can return 0 immediately
after the first atomic_read() (before doing cmpxchg). In that case it doesn't
provide any barrier semantics. See include/asm-ia64/atomic.h as an example.
We should either change the implementation, or fix the docs.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cgroup requires the subsystem to return negative error code on error in the
create method.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove this VM_BUG_ON(), as Balbir stated:
We used to have a for loop with !list_empty() as a termination condition
and VM_BUG_ON(!pc) is a spill over. With the new loop, VM_BUG_ON(!pc) does
not make sense.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Balbir Singh <balbir@in.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list head res->tasks gets initialized twice in find_css_set().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cgroup uses unsigned long for subsys bitops, not unsigned long long.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
opts.release_agent is not kfree()ed in all necessary places.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- replace old name 'cont' with 'cgrp' (Paul Menage did this cleanup for
cgroup.c in commit bd89aabc67)
- remove a duplicate declaration of cgroup_path()
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix:
- comments about need_forkexit_callback
- comments about release agent
- typo and comment style, etc.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Misc fixes and updates, make the doc consistent with current cgroup
implementation.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.meminit.text+0x649):
Section mismatch in reference from the
function free_area_init_core() to the function .init.text:setup_usemap()
The function __meminit free_area_init_core() references
a function __init setup_usemap().
If free_area_init_core is only used by setup_usemap then
annotate free_area_init_core with a matching annotation.
The warning is covers this stack of functions in mm/page_alloc.c:
alloc_bootmem_node must be marked __init.
alloc_bootmem_node is used by setup_usemap, if !SPARSEMEM.
(usemap_size is only used by setup_usemap, if !SPARSEMEM.)
setup_usemap is only used by free_area_init_core.
free_area_init_core is only used by free_area_init_node.
free_area_init_node is used by:
arch/alpha/mm/numa.c: __init paging_init()
arch/arm/mm/init.c: __init bootmem_init_node()
arch/avr32/mm/init.c: __init paging_init()
arch/cris/arch-v10/mm/init.c: __init paging_init()
arch/cris/arch-v32/mm/init.c: __init paging_init()
arch/m32r/mm/discontig.c: __init zone_sizes_init()
arch/m32r/mm/init.c: __init zone_sizes_init()
arch/m68k/mm/motorola.c: __init paging_init()
arch/m68k/mm/sun3mmu.c: __init paging_init()
arch/mips/sgi-ip27/ip27-memory.c: __init paging_init()
arch/parisc/mm/init.c: __init paging_init()
arch/sparc/mm/srmmu.c: __init srmmu_paging_init()
arch/sparc/mm/sun4c.c: __init sun4c_paging_init()
arch/sparc64/mm/init.c: __init paging_init()
mm/page_alloc.c: __init free_area_init_nodes()
mm/page_alloc.c: __init free_area_init()
and
mm/memory_hotplug.c: hotadd_new_pgdat()
hotadd_new_pgdat can not be an __init function, but:
It is compiled for MEMORY_HOTPLUG configurations only
MEMORY_HOTPLUG depends on SPARSEMEM || X86_64_ACPI_NUMA
X86_64_ACPI_NUMA depends on X86_64
ARCH_FLATMEM_ENABLE depends on X86_32
ARCH_DISCONTIGMEM_ENABLE depends on X86_32
So X86_64_ACPI_NUMA implies SPARSEMEM, right?
So we can mark the stack of functions __init for !SPARSEMEM, but we must mark
them __meminit for SPARSEMEM configurations. This is ok, because then the
calls to alloc_bootmem_node are also avoided.
Compile-tested on:
silly minimal config
defconfig x86_32
defconfig x86_64
defconfig x86_64 -HIBERNATION +MEMORY_HOTPLUG
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the Smack LSM to allow the registration of the capability "module"
as a secondary LSM. Integrate the new hooks required for file based
capabilities.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Paul Moore <paul.moore@hp.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kprobes makes use of preempt_disable(),preempt_enable_noresched() and these
functions inturn call add/sub_preempt_count(). So we need to refuse user from
inserting probe in to these functions.
This patch disallows user from probing add/sub_preempt_count().
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document huge memory/cache overhead of memory controller in Kconfig
I was a little surprised that 2.6.25-rc* increased struct page for the
memory controller. At least on many x86-64 machines it will not fit into a
single cache line now anymore and also costs considerable amounts of RAM.
At earlier review I remembered asking for a external data structure for
this.
It's also quite unobvious that a innocent looking Kconfig option with a
single line Kconfig description has such a negative effect.
This patch attempts to document these disadvantages at least so that users
configuring their kernel can make a informed decision.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Balbir Singh <balbir@in.ibm.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running "make htmldocs" I'm seeing some non-fatal perl errors caused
by trying to parse the callback function definitions in blk-core.c.
The errors are "Use of uninitialized value in concatenation (.)..."
in combination with:
Warning(linux-2.6.25-rc2/block/blk-core.c:1877): No description found for parameter ''
The function pointers are defined without a * i.e.
int (drv_callback)(struct request *)
The compiler is happy with them, but kernel-doc isn't.
This patch teaches create_parameterlist in kernel-doc to parse this type of
function pointer definition, but is it the right way to fix the problem ?
The problem only seems to occur in blk-core.c.
However with the patch applied, kernel-doc finds the correct parameter
description for the callback in blk_end_request_callback, which is doesn't
normally.
I thought it would be a bit odd to change to code to use the more normal
form of function pointers just to get the documentation to work, so I fixed
kernel-doc instead - even though this is teaching it to understand code
that might go away (The comment for blk_end_request_callback says that it
should not be used and will removed at some point).
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all architectures implement futex_atomic_cmpxchg_inatomic(). The default
implementation returns -ENOSYS, which is currently not handled inside of the
futex guts.
Futex PI calls and robust list exits with a held futex result in an endless
loop in the futex code on architectures which have no support.
Fixing up every place where futex_atomic_cmpxchg_inatomic() is called would
add a fair amount of extra if/else constructs to the already complex code. It
is also not possible to disable the robust feature before user space tries to
register robust lists.
Compile time disabling is not a good idea either, as there are already
architectures with runtime detection of futex_atomic_cmpxchg_inatomic support.
Detect the functionality at runtime instead by calling
cmpxchg_futex_value_locked() with a NULL pointer from the futex initialization
code. This is guaranteed to fail, but the call of
futex_atomic_cmpxchg_inatomic() happens with pagefaults disabled.
On architectures, which use the asm-generic implementation or have a runtime
CPU feature detection, a -ENOSYS return value disables the PI/robust features.
On architectures with a working implementation the call returns -EFAULT and
the PI/robust features are enabled.
The relevant syscalls return -ENOSYS and the robust list exit code is blocked,
when the detection fails.
Fixes http://lkml.org/lkml/2008/2/11/149
Originally reported by: Lennart Buytenhek
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Riku Voipio <riku.voipio@movial.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the futex init code fails to initialize the futex pseudo file system it
returns early without initializing the hash queues. Should the boot succeed
then a futex syscall which tries to enqueue a waiter on the hashqueue will
crash due to the unitilialized plist heads.
Initialize the hash queues before the filesystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Riku Voipio <riku.voipio@movial.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list. This is however what we do in dmi_scan
since commit 79da472111 ("x86: fix DMI out
of memory problems").
Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/video/built-in.o(.text+0x7c64a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c65d): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c679): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c699): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c69f): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3676): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3689): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36a5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36c5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36cb): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a079a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ad): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07c9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07e9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ef): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
Remove __devinitdata annotation from the variable ypan.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RLIMIT_RTTIME was introduced to allow the user to set a runtime timeout on
real-time tasks: http://lkml.org/lkml/2007/12/18/218. This patch updates
/proc/<pid>/limits with the new rlimit.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge include/linux/efs_fs{_i,_dir}.h into fs/efs/efs.h. efs_vh.h remains
there because this is the IRIX volume header and shouldn't really be
handled by efs but by the partitioning code. efs_sb.h remains there for
now because it's exported to userspace. Of course this wrong and aboot
should have a copy of it's own, but I'll leave that to a separate patch to
avoid any contention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.
The two problems I have experienced with nbd and cfq are:
1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
fixed
There's a similar debian bug that has been filed as well:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638
There have been posts to nbd-general mailing list about problems with
cfq and nbd also.
2) nbd performs about 10% better (the last time I tested) with deadline
vs. cfq (the overhead of cfq doesn't provide much advantage to nbd [not
being a real disk], and you end up going through the I/O scheduler on
the nbd server anyway, so it makes sense that deadline is better with
nbd)
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ee3d9bd4de ("uml: simplify SIGSEGV
handling"), while greatly simplifying the kernel SIGSEGV handler that
runs in the process address space, introduced a bug which corrupts FP
state in the process.
Previously, the SIGSEGV handler called the sigreturn system call by hand - it
couldn't return through the restorer provided to it because that could try to
call the libc restorer which likely wouldn't exist in the process address
space. So, it blocked off some signals, including SIGUSR1, on entry to the
SIGSEGV handler, queued a SIGUSR1 to itself, and invoked sigreturn. The
SIGUSR1 was delivered, and was visible to the UML kernel after sigreturn
finished.
The commit eliminated the signal masking and the call to sigreturn. The
handler simply hits itself with a SIGTRAP to let the UML kernel know that it
is finished. UML then restores the process registers, which effectively
longjmps the process out of the signal handler, skipping sigreturn's restoring
of register state and the signal mask.
The bug is that the host apparently sets used_fp to 0 when it saves the
process FP state in the sigcontext on the process signal stack. Thus, when
the process is longjmped out of the handler, its FP state is corrupt because
it wasn't saved on the context switch to the UML kernel.
This manifested itself as sleep hanging. For some reason, sleep uses floating
point in order to calculate the sleep interval. When a page fault corrupts
its FP state, it is faked into essentially sleeping forever.
This patch saves the FP state before entering the SIGSEGV handler and restores
it afterwards.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 1aa351a308 ("uml: tidy helper
code") the arguments of helper_wait() were changed. The adaptation of
harddog_user.c was forgotten, so this errors occur:
/arch/um/drivers/harddog_user.c: In function 'start_watchdog':
/arch/um/drivers/harddog_user.c:82: error: too many arguments to function 'helper_wait'
/arch/um/drivers/harddog_user.c:89: error: too many arguments to function 'helper_wait'
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The macros which extract registers from a struct sigcontext are no longer
needed and can be removed. They are starting not to build anyway, given the
removal of the 'e' and 'r' from register names during the x86 merge.
Cc: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect. Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
