Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)
Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)
The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.
We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This makes the intc show up in sysfs (probably not very useful), and
allows us to easily add suspend/resume support later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SDRAM controller needs a clock in order to respond to our
commands, and suspend doesn't work very well without the SDRAM in
self-refresh mode.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Call device_init_wakeup() to signal that the RTC is capable of waking
the system. This is needed for rtcwake to work.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
This implements suspend and resume callbacks for the macb driver. We may
have to do some more to gracefully shut the MAC down, but this at least
prevents the macb from waking the system when hooked up to a busy
network.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Funny things may happen if we stop the USART clock before the shifter is
empty. Prevent this from happening by waiting until the shifter is
completely drained before allowing suspend to continue.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
AVR32 doesn't have at91_suspend_entering_slow_clock(). Just assume the
clock will keep running for now.
David has a better solution for this, but this works for now. Leaving
the USART clock running won't prevent the PM code from entering deep
power-down modes anyway.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Using a quicklist to allocate PTEs might be slightly faster than using
the page allocator directly since we might avoid zeroing the page
after each allocation.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Use a quicklist to allocate process PGDs. This is expected to be
slightly faster since we need to copy entries from swapper_pg_dir,
which can stay around for pages on the PGD quick list.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Expand the per-process PGDs so that they cover the kernel virtual
memory area as well. This simplifies the TLB miss handler fastpath
since it doesn't have to check for kernel addresses anymore.
If a TLB miss happens on a kernel address and a second-level page
table can't be found, we check swapper_pg_dir and copy the PGD entry
into the user PGD if it can be found there.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Instead of storing physical addresses along with page flags in the
PGD, store virtual addresses and use NULL to indicate a not present
second-level page table. A non-page-aligned page table indicates a bad
PMD.
This simplifies the TLB miss handler since it no longer has to check
the Present bit and no longer has to convert the PGD entry from
physical to virtual address. Instead, it has to check for a NULL
entry, which is slightly cheaper than either.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This and the following patches aim to optimize the code dealing with
page tables and TLB operations. Each patch reduces the time it takes
to gzip a 16 MB file slightly, but I expect things like fork() and
mmap() will improve somewhat more.
This patch deals with the low-level TLB operations:
* Remove unused _TLBEHI_I define
* Use gcc builtins instead of inline assembly
* Remove a few unnecessary pipeline flushes and nops
* Introduce NR_TLB_ENTRIES define and use it instead of hardcoding it
to 32 a few places throughout the code.
* Use sysreg bitops instead of hardcoded shifts and masks
* Make a few needlessly global functions static
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Basic I2C initialization for the NGW100 board:
- Provide empty i2c device table. Daughtercards may add devices,
and the ATtiny24 could do stuff too.
- Set up EXTINT(3) so the ATtiny24 can interrupt the AP7000.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.
The function for adding the PSIF platform device is also added to the
board header file.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
__raw_readsb() should always use byte accesses, never halfword accesses,
to I/O memory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A signal handler should be able to change the signal stack used for the
next signal by altering the ucontext_t passed as a parameter to the
handler. This does not currently work on avr32 since it doesn't update
the in-kernel signal context from the ucontext_t upon signal handler
return.
Fix it by adding a call to do_sigaltstack() from sys_rt_sigreturn(),
bringing it in line with most other architectures.
Signed-off-by: Martin Koegler <mkoegler@auto.tuwien.ac.at>
[haavard.skinnemoen@atmel.com: changed patch description]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On our custom board we have other oscillator rates than on atngw100 and
atstk100x.
Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.
This patch moves them into board specific code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fixes one of two ext4 build problems:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some non-PCI drivers need the PCI variant of the DMA mapping API.
Include <asm-generic/pci-dma-compat.h> to provide this through the
non-PCI DMA mapping API.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
[IA64] Handle count==0 in sn2_ptc_proc_write()
[IA64] Fix boot failure on ia64/sn2
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Remove now unused structs from kvm_para.h
x86: KVM guest: Use the paravirt clocksource structs and functions
KVM: Make kvm host use the paravirt clocksource structs
x86: Make xen use the paravirt clocksource structs and functions
x86: Add structs and functions for paravirt clocksource
KVM: VMX: Fix host msr corruption with preemption enabled
KVM: ioapic: fix lost interrupt when changing a device's irq
KVM: MMU: Fix oops on guest userspace access to guest pagetable
KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
KVM: MMU: Fix rmap_write_protect() hugepage iteration bug
KVM: close timer injection race window in __vcpu_run
KVM: Fix race between timer migration and vcpu migration
On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function. With this patch, vblank interrupts will work as expected
on resume, along with other chip functions. Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kvm_* structs are obsoleted by the pvclock_* ones.
Now all users have been switched over and the old structs
can be dropped.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.
The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup. kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch updates the xen guest to use the pvclock structs
and helper functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).
It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code. They are enabled using
CONFIG_PARAVIRT_CLOCK.
Subsequent patches of this series will put the code in use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch fixes bz 450641.
This patch changes the computation for zero_metapath_length(), which it
renames to metapath_branch_start(). When you are extending the metadata
tree, The indirect blocks that point to the new data block must either
diverge from the existing tree either at the inode, or at the first
indirect block. They can diverge at the first indirect block because the
inode has room for 483 pointers while the indirect blocks have room for
509 pointers, so when the tree is grown, there is some free space in the
first indirect block. What metapath_branch_start() now computes is the
height where the first indirect block for the new data block is located.
It can either be 1 (if the indirect block diverges from the inode) or 2
(if it diverges from the first indirect block).
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory. Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The fix applied in e0c6d97c65
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0'). Thanks to Andi Kleen for
pointing this out.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Call check_sal_cache_flush() after platform_setup() as
check_sal_cache_flush() now relies on being able to call platform
vector code.
Problem was introduced by: 3463a93def
"Update check_sal_cache_flush to use platform_send_ipi()"
Signed-off-by: Jes Sorensen <jes@sgi.com>
Tested-by: Alex Chiang: <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- Fix warning reported by sparse
kernel/kgdb.c:1502:6: warning: symbol 'kgdb_console_write' was not declared.
Should it be static?
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
kgdboe is not presently included kgdb, and there should be no
references to it.
Also fix the tcp port terminal connection example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used. xen-unstable has now officially dropped
non-PAE support. Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
