Convert code in core/ to use the new DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch implements the interposing DMA mapping functions to allow
support for IOMMUs and remove the dependence on phys_to_virt() and
bus_to_virt().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The QLogic InfiniPath HCAs use programmed I/O instead of HW DMA.
This patch allows a verbs device driver to interpose on DMA mapping
function calls in order to avoid relying on bus_to_virt() and
phys_to_virt() to undo the mappings created by dma_map_single(),
dma_map_sg(), etc.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export the rdma cm interfaces to userspace via a misc device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow the use of UD QPs through the rdma_cm, in order to provide
address translation services for resolving IB addresses for datagram
messages using SIDR.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During connection establishment, the passive side of a connection can
receive messages from the active side before the connection event has
been delivered to the user. Allow the passive side to send messages
in response to received data before the event is delivered. To handle
the case where the connection messages are lost, a new rdma_notify()
function is added that users may invoke to force a connection into the
established state.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connection information was never given to the recipient of a
connection request or reply message. Only the event was delivered.
Report the connection data with the event to allows user to
reject the connection based on the requested parameters, or adjust
their resources to match the request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The qp_type parameter into the rdma_cm is unneeded, and can be
misleading. The QP type should be determined from the port space.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 51f65ebc ("IB/ipath - program intconfig register using new HT
irq hook"), which fixed interrupts for HyperTransport HCAs, broke PCI
Express HCAs, because for those HCAs, the driver uses the value of
pdev->irq before pci_enable_msi() and ends up getting a totally bogus
IRQ number. Fix this by using the value of pdev->irq after
pci_enable_msi().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the iSER
initiator. These cleanups came from David Binderman's list of "set
but never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the ipath
driver. These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_flush_fmr_pool() stashes away the request generation number
properly, but then goes ahead and rereads it every time it tests
whether the flush generation number has caught up. This means that
there is a theoretical possibility of livelock, if the request
generation number keeps getting bumped and the flush generation number
never catches up. The fix is simple: use the request generation
number read at the beginning of the function.
Also, atomic_inc() followed by atomic_read() can be replaced with
atomic_int_return(). There's no real requirement for atomicity here
but we might as well shrink the code.
This bug was discovered using David Binderman's list of "set but never
used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 2d4ba4a3b9 introduced a dependency
that was never meant to exist when the ac97_bus.c module was created.
Move ac97_bus.c up the directory hierarchy to make sure it is built when
selected even if sound is configured out so things work as originally
intended.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix OMAP clock prescaler to match the comment
i2c: Refactor a kfree in i2c-dev
i2c: Fix return value check in i2c-dev
i2c: Enable PEC on more i2c-i801 devices
i2c: Discard the i2c algo del_bus wrappers
i2c: New ARM Versatile/Realview bus driver
i2c: fix broken ds1337 initialization
i2c: i2c-i801 documentation update
i2c: Use the __ATTR macro where possible
i2c: Whitespace cleanups
i2c: Use put_user instead of copy_to_user where possible
i2c: New Atmel AT91 bus driver
i2c: Add support for nested i2c bus locking
i2c: Cleanups to the i2c-nforce2 bus driver
i2c: Add request/release_mem_region to i2c-ibm_iic bus driver
i2c: New Philips PNX bus driver
i2c: Delete the broken i2c-ite bus driver
i2c: Update the list of driver IDs
i2c: Fix documentation typos
current -git doesnt boot on my laptop due to netpoll not unlocking the
tx lock in the else branch.
booted this up on my laptop with lockdep enabled and there are no
locking complaints and it works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
seqlock_init() needs to use spin_lock_init() for dynamic locks, so that
lockdep is notified about the presence of a new lock.
(this is a fallout of the recent networking merge, which started using
the so-far unused seqlock_init() API.)
This fix solves the following lockdep-internal warning on current -git:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
__lock_acquire+0x10c/0x9f9
lock_acquire+0x56/0x72
_spin_lock+0x35/0x42
neigh_destroy+0x9d/0x12e
neigh_periodic_timer+0x10a/0x15c
run_timer_softirq+0x126/0x18e
__do_softirq+0x6b/0xe6
do_softirq+0x64/0xd2
ksoftirqd+0x82/0x138
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4954): Fix: On ia64, i2c adap->inb/adap->outb are wrongly evaluated
i2c defines two callbacks (inb/outb). On ia64, since it defines also two macros
with those names, it causes the following errors:
drivers/media/video/usbvision/usbvision-i2c.c:64:39: macro "outb" passed 4 arguments, but takes just 2
drivers/media/video/usbvision/usbvision-i2c.c: In function `try_write_address':
drivers/media/video/usbvision/usbvision-i2c.c:64: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:89:38: macro "inb" passed 4 arguments, but takes just 1
drivers/media/video/usbvision/usbvision-i2c.c: In function `try_read_address':
drivers/media/video/usbvision/usbvision-i2c.c:89: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:85: warning: unused variable `buf'
drivers/media/video/usbvision/usbvision-i2c.c:173:53: macro "inb" passed 4 arguments, but takes just 1
drivers/media/video/usbvision/usbvision-i2c.c: In function `usb_xfer':
drivers/media/video/usbvision/usbvision-i2c.c:173: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:179:54: macro "outb" passed 4 arguments, but takes just 2
drivers/media/video/usbvision/usbvision-i2c.c:179: warning: assignment makes integer from pointer without a cast
thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When I converted the original patch, I left unnecessary blk_queue_bounce in
SG_IO.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes bio leaks in SG_IO. rq->bio can be changed after io
completion, so we need to reset rq->bio before calling blk_rq_unmap_user()
http://marc.theaimsgroup.com/?l=linux-kernel&m=116570666807983&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
While working on bidi support at struct request level
I have found that blk_queue_activity_fn is actually never used.
The only user is in ide-probe.c with this code:
/* enable led activity for disk drives only */
if (drive->media == ide_disk && hwif->led_act)
blk_queue_activity_fn(q, hwif->led_act, drive);
And led_act is never initialized anywhere.
(Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18)
Unless it is all for future use off course.
(this patch is against linux-2.6-block.git as off 2006/12/4)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Add missing #include <linux/param.h> to delay.c
[AVR32] Pass dev parameter to dma_cache_sync()
[AVR32] Implement intc_get_pending()
[AVR32] Don't include <asm/delay.h>
[AVR32] Put the chip in "stop" mode when halting the system
[AVR32] Set flow handler for external interrupts
[AVR32] Remove unused file
[AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data
[AVR32] Move ethernet tag parsing to board-specific code
[AVR32] Add macb1 platform_device
[AVR32] Portmux API update
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
This patch makes paging_init() use highend_pfn/highstart_pfn globals.
It removes the need of 'high' local which was needed only by HIGHMEM config.
More important perhaps, it fixes a bug when HIGHMEM is set but there's
actually no physical highmem (highend_pfn = 0)
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While the recent cset 86384d5441 did improve
things it didn't resolve all the problems. So bite the bullet and discard
.exit.text and .exit.data at runtime. Which of course sucks because it
bloats binaries with code that will never ever be used but it's the only
thing that will work reliable as demonstrated by the function sd_major() in
drivers/scsi/sd.c.
Gcc may compile sd_major() using a jump table which it will put into
.rodata. If it also inlines sd_major's function body into exit_sd() which
gcc > 3.4.x does. If CONFIG_BLK_DEV_SD has been set to y we would like ld
to discard exit_sd's code at link time. However sd_major happens to
contain a switch statement which gcc will compile using a jump table in
.rodata on the architectures I checked. So, when ld later discards
.exit.text only the jump table in .rodata with its stale references to
the discard .exit.text will be left which any no antique ld will honor
with a link error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During boot we get:
netconsole: device eth0 not up yet, forcing it
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
WARNING (!__warned) at kernel/softirq.c:137 local_bh_enable()
Call Trace:
[<ffffffff80235baf>] local_bh_enable+0x41/0xa3
[<ffffffff8045ab8e>] netpoll_send_skb+0x116/0x144
[<ffffffff8045b1ee>] netpoll_send_udp+0x263/0x271
[<ffffffff803d41ec>] write_msg+0x42/0x5e
[<ffffffff80230c9b>] __call_console_drivers+0x5f/0x70
[<ffffffff80230d19>] _call_console_drivers+0x6d/0x71
[<ffffffff802313f0>] release_console_sem+0x148/0x1ec
[<ffffffff802316ce>] register_console+0x1b1/0x1ba
[<ffffffff803d4178>] init_netconsole+0x54/0x68
[<ffffffff802071ae>] init+0x152/0x308
[<ffffffff804dac8b>] _spin_unlock_irq+0x14/0x30
[<ffffffff8022c15e>] schedule_tail+0x43/0x9f
[<ffffffff8020a758>] child_rip+0xa/0x12
Herbert sayeth:
Normally networking isn't invoked with interrupts turned off, but I
suppose we don't have a choice here. This is unique being a place where you
can get called with BH on, off, or IRQs off.
Given that this is only used for printk, the easiest solution is probably
just to disable local IRQs instead of BH.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds in support for the BUG() trap on SH-2.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was inadvertently broken when the entry.S code split up,
restore the missing branch and get subsequent traps working
under debug again. This manifested itself as a lockup when
attempting to reload the VBR base.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2 and SH-2A need to use a different syscall base for the trapa
vector than the other parts, so fixup the logic in the kernel_execve()
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some time ago the schedule frame size changed and we failed to reflect
this in get_wchan() at the time. This first popped up as a problem on
SH7751R where schedule_frame ended up being unaligned and generating
an unaligned trap. This fixes it up again..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we haven't been doing anything with verbose BUG() reporting,
and we've been relying on the oops path for handling BUG()'s, which is
rather sub-optimal.
This switches BUG handling to use a fixed trapa vector (#0x3e) where we
construct a small bug frame post trapa instruction to get the context
right. This also makes it trivial to wire up a DIE_BUG for the atomic
die chain, which we couldn't really do before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds alarm support for the RTC_ALM_SET, RTC_ALM_READ,
RTC_WKALM_SET and RTC_WKALM_RD operations to rtc-sh.
The only unusual part is the handling of the alarm interrupt. If you
clear the alarm flag (AF) while the time in the RTC still matches the
time in the alarm registers than AF is immediately re-set, and if the
alarm interrupt (AIE) is still enabled then it re-triggers. I was
originally getting around 20k+ interrupts generated during the second
when the RTC and alarm registers matches.
The solution I've used is to clear AIE when the alarm goes off and
then use the carry interrupt to re-enabled it. The carry interrupt
will check AF and re-enabled AIE if it's clear. If AF is not clear
it'll clear it and then the check will be repeated next carry
interrupt. This a bit in rtc structure that indicates that it's
waiting to have AIE re-enabled so it doesn't turn it on when it
wasn't enabled anyway.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
