rfkill_mutex and rfkill->mutex are too easy to confuse with each other.
Rename rfkill_mutex to rfkill_global_mutex, so that they are easier to tell
apart with just one glance.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BUG_ON() and WARN() the heck out of buggy drivers calling into the rfkill
subsystem.
Also switch from WARN_ON(1) to the new descriptive WARN().
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial patch adding a missing line break on
rfkill_claim_show().
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.co>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switch sysfs parsing to something that actually works properly.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kernel doc syntax for comments and remove a few unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54_rx_frame_sent will alter the tx_queue. Therefore we should hold
the lock to protect against concurrent p54_assign_address calls.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?
Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...
So now, big question: what happens when we blindly "memcpy" these data points?
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/b43legacy/main.c
drivers/net/wireless/iwlwifi/iwl-3945-led.c
drivers/net/wireless/iwlwifi/iwl-led.c
drivers/net/wireless/iwlwifi/iwl-rfkill.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some semi-random values for HT and add more queues to allow IEEE
802.11n association to be tested with mac80211_hwsim. This with the
latest hostapd git tree version can complete a simulated 802.11n
association successfully (with mac80211 client MLME).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only rev 1 and 2 ssb SPROMs have fields named et0mac and et1mac;
however, all of the extraction routines extract pseudo data for these
fields from regions that are all 1's resulting in a hardware address
of FF:FF:FF:FF:FF:FF. This patch forces such a fill at the beginning of
the data extraction process, and only does the formal extraction if the
SPROM rev is 1 or 2.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and return errors for operations like join & scan that aren't possible
when the radio is turned off.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and remove DISASSOCIATE because it's not in any of the specs and has
never been used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And while we're at it, grab min/max TX power from the firmware and use
that to validate incoming TX power requests from WEXT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although a revision 5 SPROM has not been seen in the wild, the
open-source portion of the MIPS driver 4.150.10.5 describes its
layout, which is mostly inherited from revision 4. This patch
implements the differences.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 4-5 of DSCP should not be considered by classify_d1. The
802.11 QoS Priority field is only depending on the precedence level.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and extend scan result processing by storing all the IEs from
Beacon/Probe Response frames in a single block instead of allocating
memory for each specific IE separately. This removes lot of unnecessary
code and automatically supports reporting of new IEs (e.g., IEEE
802.11r) into user space without need to manually extend mac80211
scanning code whenever a new protocol adds IE(s).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't trim the FCS before passing the frame to mac80211,
move TSF_TO_TU to core.h and delete more unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, Max RX-ampdu and mpdu-density are ath9k specific.
Rename appropriately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a HT Capability (DSSS/CCK Mode in 40MHz BSS)
definition to ieee80211.h
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ath_vap_listen() and dma wrapper macros.
Also, Inline abuse is cleaned up and a few typos are fixed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct pci functions instead.
Also, use sc_ht_info.tx_chan_width directly and remove ath_cwm_macmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change moves ath9k to use mac80211-generated Beacon frames instead
of trying to allocate a single Beacon frame and then update it. In
addition, the remaining ath_skb_{map,unmap}_single() wrapper calls are
replaced with direct pci_{map,unmap}_single() calls in beacon.c. Power
save buffering for multicast/broadcast frames is not yet converted to
use mac80211-style (frames to be buffered inside mac80211, not in
driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sc_rxflush and sc_noreset as bitfields to sc_flags.
Remove a few variables and function prototypes that are unused.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah_opmode and sc_opmode are redundant.
This patch removes sc_opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow
AP mode BSS parameters to be changed from user space (e.g., hostapd).
The drivers using mac80211 are expected to be modified with separate
changes to use the new BSS info parameter for short slot time in the
bss_info_changed() handler.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, drivers are required to keep track of the sequence numbers
themselves, and they really shouldn't be since we already do it for
them. I'll fix the race once we figure out how this code should work
at all, it's currently disabled.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BUG_ON(w_tot == 0) only holds if there is no more than 1 loss interval in
the loss history. If there is only a single loss interval, the calc_i_mean()
routine need in fact not be called (RFC 3448, 6.3.1).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
