Inside a function declared as
void foo(char bar[512])
the value of sizeof bar is the size of a pointer, not 512. So avoid
constructions like this by passing the size explicitly.
Also reduce the size of the buffer to 128 bytes (512 was overly generous).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The small eeprom that holds the GUID etc. contains a data-length, but if
the actual eeprom is new or has been erased, that byte will be 0xFF,
which is greater than the maximum physical length of the eeprom, and
more importantly greater than the length of the buffer we vmalloc'd.
Sanity-check the length to avoid the possbility of reading past end of
buffer.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a small window where a send work queue entry could be
overwritten by ib_post_send() because s_last is updated before the
entry is read.
This patch closes the window by acquiring the lock and updating
the last send work queue entry index after reading the wr_id.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as
mlx4_ib_post_recv(). Correct the code so the intended sq.lock is
taken when posting a send.
Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from
Mellanox.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 1b524963 ("IPoIB/cm: Use common CQ for CM send completions")
changed how the high-order bits of work request IDs were used, which
had the effect that IPOIB_CM_RX_DRAIN_WRID was no longer handled as a
connected mode receive completion. This leads to the messages
ib1: cm send completion event with wrid 1073741823 (> 64)
ib1: RX drain timing out
when an interface with connected mode QPs is brought down. Fix this
by making sure that both IPOIB_OP_CM and IPOIB_OP_RECV are set in
IPOIB_CM_RX_DRAIN_WRID.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Increase command timeout for INIT_HCA to 10 seconds
IPoIB/cm: Use common CQ for CM send completions
IB/uverbs: Fix checking of userspace object ownership
IB/mlx4: Sanity check userspace send queue sizes
IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))"
IB/ehca: Enable large page MRs by default
IB/ehca: Change meaning of hca_cap_mr_pgsize
IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr()
IB/ehca: Fix masking error in {,re}reg_phys_mr()
IB/ehca: Supply QP token for SRQ base QPs
IPoIB: Use round_jiffies() for ah_reap_task
RDMA/cma: Fix deadlock destroying listen requests
RDMA/cma: Add locking around QP accesses
IB/mthca: Avoid alignment traps when writing doorbells
mlx4_core: Kill mlx4_write64_raw()
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (45 commits)
Use "struct boot_params" in example launcher
Loading bzImage directly.
Revert lguest magic and use hook in head.S
Update lguest documentation to reflect the new virtual block device name.
generalize lgread_u32/lgwrite_u32.
Example launcher handle guests not being ready for input
Update example launcher for virtio
Lguest support for Virtio
Remove old lguest I/O infrrasructure.
Remove old lguest bus and drivers.
Virtio helper routines for a descriptor ringbuffer implementation
Module autoprobing support for virtio drivers.
Virtio console driver
Block driver using virtio.
Net driver using virtio
Virtio interface
Boot with virtual == physical to get closer to native Linux.
Allow guest to specify syscall vector to use.
Rename "cr3" to "gpgdir" to avoid x86-specific naming.
Pagetables to use normal kernel types
...
As it is some callers of synchronize_irq rely on memory barriers
to provide synchronisation against the IRQ handlers. For example,
the tg3 driver does
tp->irq_sync = 1;
smp_mb();
synchronize_irq();
and then in the IRQ handler:
if (!tp->irq_sync)
netif_rx_schedule(dev, &tp->napi);
Unfortunately memory barriers only work well when they come in
pairs. Because we don't actually have memory barriers on the
IRQ path, the memory barrier before the synchronize_irq() doesn't
actually protect us.
In particular, synchronize_irq() may return followed by the
result of netif_rx_schedule being made visible.
This patch (mostly written by Linus) fixes this by using spin
locks instead of memory barries on the synchronize_irq() path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Add Vitaly Bordug as PPC8xx maintainer
[POWERPC] 4xx: Enable EMAC on Bamboo board
[POWERPC] 4xx: Enable EMAC for PPC405 Walnut board
[POWERPC] 4xx: Fix timebase clock selection on Walnut
[POWERPC] 4xx: Enable EMAC on the PPC 440GP Ebony board
[POWERPC] 4xx: Split early debug output and early boot console for 44x
[POWERPC] 4xx: Enable NEW EMAC support for Sequoia 440EPx.
[POWERPC] 4xx: Add RGMII support for Sequoia 440EPx
* git://git.infradead.org/mtd-2.6:
[MTD] [NOR] Fix deadlock in Intel chip driver caused by get_chip recursion
[JFFS2] Fix return value from jffs2_write_end()
[MTD] [OneNAND] Fix wrong free the static address in onenand_sim
[MTD] [NAND] Replace -1 with -EBADMSG in nand error correction code
[RSLIB] BUG() when passing illegal parameters to decode_rs8() or decode_rs16()
[MTD] [NAND] treat any negative return value from correct() as an error
[MTD] [NAND] nandsim: bugfix in initialization
[MTD] Fix typo in Alauda config option help text.
[MTD] [NAND] add s3c2440-specific read_buf/write_buf
[MTD] [OneNAND] onenand-sim: fix kernel-doc and typos
[JFFS2] Tidy up fix for ACL/permissions problem.
Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.
Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A new style serial driver for the Freescale ColdFire UART to replace
the old style one currently in the tree (drivers/serial/mcfserial.c).
Currently this UART is only found in the ColdFire CPU family of parts
(thus I prefixed this patch [M68KNOMMU]).
This has been around for a long while now, tested on all available
platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve the readability of mii_do_cmd().
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix system call restart handling. We can call directly to the
restart handler, no need to back track through trap that isn't
even implemented on m68knommu.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add make support for the Savant/Rosie1 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no separate stack region addresses to print at startup time,
so remove it from the debug listing
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Savant/Rosie1 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updated defconfig with new options for m68knommu.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Up to now m68knommu has been using the asm-m68k/module.h instead of
defining its own. There are recent changes there that we don't need
(fixups specifically). We don't need much support here so it makes
sense to have an m68knommu specific one now.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define __clear_user macro, consistent with other architectures.
fs/signalfd.c won't compile without it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the system call code for handling syscall tracing, so strace
and gdbserver work properly.
This fix originally developed by Philippe De Muyter and Stuart Hughes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Indent all the `else' the same way.
Remove some unecesary white space.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ztxdone is jumped to even if tty is NULL and tty_wakeup placed after
this label doesn't expect NULLed parameter, so this will cause an oops
in some situations (why they scheduled a wakeup there before remove
bottom half processing patch?).
wakeup only in the case when we have non-null tty struct.
Spotted by Adrian Bunk.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mprotect bug in recent commit 3ed75eb8f1
(setup vma->vm_page_prot by vm_get_page_prot()): the vma_wants_writenotify
case was setting the same prot as when not.
Nothing wrong with the use of protection_map[] in mmap_region(),
but use vm_get_page_prot() there too in the same ~VM_SHARED way.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Coly Li <coyli@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ops_complete_biofill() runs outside of spin_lock(&sh->lock) and clears the
'pending' and 'ack' bits. Since the test_and_ack_op() macro only checks
against 'complete' it can get an inconsistent snapshot of pending work.
Move the clearing of these bits to handle_stripe5(), under the lock.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As page->index is unsigned, this all becomes an unsigned comparison,
which almost always returns an error.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch solves kernel deadlock issue seen on JFFF2 simultaneous
operations. Detailed investigation of the issue showed that the kernel
deadlock is caused by tons of recursive get_chip calls.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
zero out dma_length in the entry immediately following the last mapped
entry for unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sctp fails to compile with
net/sctp/sm_make_chunk.c: In function 'sctp_pack_cookie':
net/sctp/sm_make_chunk.c:1516: error: implicit declaration of function 'sg_init_table'
net/sctp/sm_make_chunk.c:1517: error: implicit declaration of function 'sg_set_page'
use the proper include file.
SCTP maintainers Vlad Yasevich and Sridhar Samudrala are CCed.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement at32_add_device_cf() which will add a platform_device for
the at32_cf driver (not merged yet). Separate out most of the
at32_add_device_ide() code and use it to implement
at32_add_device_cf() as well.
This changes the API in the following ways:
* The board code must initialize data->cs to the chipselect ID to
use before calling any of these functions.
* The board code must use GPIO_PIN_NONE to indicate unused CF pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for adding platform devices for TWI, MCI, AC97C
and ABDAC. They may need to be modified to cope with platform data,
etc. when the corresponding drivers are ready to be merged, but such
changes are much less likely to conflict than adding support for a
whole new type of device.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds platform code for PATA devices on the AP7000.
[hskinnemoen@atmel.com: board code left out for now since stk1000
doesn't support IDE out of the box]
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
