driver returns min buffer count to client which includes
extra buffers count which is required for batching even
though batching may be disabled in start_streaming() later.
So decide batching in set format (configuration) to avoid
adding extra buffers count to reduce memory usage in
non-batching cases.
Change-Id: I147f7aaf928074a23c9dcda2dbf69a744cec382d
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
Add support to disable both auto blur and
external blur.
Change-Id: I5200f738ffa5849a3e840f90f0da66c38607ceae
Signed-off-by: Qiwei Liu <qiweil@codeaurora.org>
Use the existing batch enable variable instead of extra
variable decode_batching.
Change-Id: Ic7875caf2b0d2c47d77b0c0c0ce9b5792920cafc
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
Decode session needs UBWC CR statistics for BW calculations.
Hence need to enable this exetradata by default.
CRs-Fixed: 2467542
Change-Id: I3955a0b09cf82f97478c31704be6b16f297b011b
Signed-off-by: Chinmay Sawarkar <chinmays@codeaurora.org>
during load resource firmware will check input buffer type
against requested buffer type. If there a mismatch it will
throw an error. So cleared non-requested buffer from the
scratch buffer list
Change-Id: Ifabf532982a393d4fc356ff3cad0ca3fd715fce0
Signed-off-by: Govindaraj Rajagopal <grajagop@codeaurora.org>
Existing code updates the device clock before cx ipeak logic.
As a result, the cx ipeak takes a decision based on updated
clock rather than the clock at which the device was running.
With the change, device clock is updated after the cx ipeak
is decided.
Change-Id: Icfde29176f8adb3a12c68a611f47b83ca7a8e4a9
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Manikanta Kanamarlapudi <kmanikan@codeaurora.org>
Perf mode can be either predefined or can be decided dynamically.
It is configured differently for different video hardware versions.
Perf mode is now updated with below
1. Remove multicore calculation as it is not applicable for single core
hardware.
2. Rate control type CQ is considered during load calculation
3. If the clocks are available, keep higher perf mode, unless restricted
by the hardware specification.
CRs-Fixed: 2462264
Change-Id: I9328e07ea3d1667b15a431c624112f1e8f8c92e0
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
operating rate setting to firmware is not required for decoder.
Change-Id: I271a42822f4a00e95d875400e5ad273697c94ab1
Signed-off-by: Govindaraj Rajagopal <grajagop@codeaurora.org>
Video port resolution can be updated during reconfig event itself.
With this, reconfig height and width was removed. Also relevant
code cleanup was made accordingly.
Change-Id: I4fb38563b4c747eb356f28b7df7e99bd397ff8d1
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Fix to check f/w logging route based on
local flag variant instead of the global one.
Because route maybe updated when error occurred.
Change-Id: Ia67e138a2b494da465f4868553d33509e70020eb
Signed-off-by: Shi Zhongbo <zhongbos@codeaurora.org>
Requirement stipulates OPB to be writable buffer in split mode.
Erring out in case of read only buffer will help debugging quickly.
Change-Id: I529a97b3d0aa5f82e7cf7d024475338a9d24d1dd
Signed-off-by: Amit Shekhar <ashekhar@codeaurora.org>
Include BRS control id in msm_venc_s_ctrl to add
support to BRS feature.
Change-Id: I05b23e7960128a7b19c582caa5123849ba0cb2b0
Signed-off-by: Akshata Sahukar <asahukar@codeaurora.org>
Cleaning up the debug change - reset max_tries count
from 10000 to 1000.
Change-Id: Id0b142f92b8f45eaa73ab256b7b07bb10f382b80
Signed-off-by: Govindaraj Rajagopal <grajagop@codeaurora.org>
Clean up debug log levels as:
1. Revise VIDC_WARN to VIDC_ERR;
2. Revise VIDC_PROF as VIDC_PERF;
3. Mark some one-time logs, e.g most of logs
in initialization and deinitialization as VIDC_HIGH;
4. Keep VIDC_PKT;
5. All other logs change to VIDC_LOW;
Change-Id: I8fc30f97dc3424da8418aab00e8af074ec8d4ef9
Signed-off-by: Shi Zhongbo <zhongbos@codeaurora.org>
DCVS feature depends on multiple client configurations.
Low latency, thumbnail mode, etc are few among them.
DCVS is now decided before the session starts streaming
i.e after all configuration are inplace.
CRs-Fixed: 2457035
Change-Id: I4a42ae6bafdc852e81794b69d117f5821af4841f
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Chinmay Sawarkar <chinmays@codeaurora.org>
Reverting 2735098 "update video dimensions during port reconfiguration".
Change-Id: I2343cf77d23a564c3346d71dae9cd6377ae9d4e2
Signed-off-by: Shivendra Kakrania <shiven@codeaurora.org>
During a decode session, video output port can go through
reconfiguration. As a result, update the reconfig dimension
when client calls for g_fmt on output port.
Change-Id: Ib5f5866acbdfe107ba4693b8b94498d42f74b312
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
CVP usage is not supported for secure session so do not
enable CVP usage for secure session.
Change-Id: Ifed6daaf706895ebbc56b246134d9775787c7b9d
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
Fix to independently control f/w logging route.
Change-Id: I81b57995cb9619d2dee9c43547e86cc3f08d3778
Signed-off-by: Shi Zhongbo <zhongbos@codeaurora.org>
Driver need not support sessions if cumulative
mbpf (macroblocks per frame) is more than platform
specified value. So reject such sessions.
Change-Id: Id12eedfb97783b746c771066d6a556692be84c9f
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
For H264 decoder, resolutions with non-multiple of 16 were
calculating less internal buffer size. Updated calculation
to handle such scenarios.
Change-Id: I3c07b843cc898a584aba4c9f26627898a7427fe8
Signed-off-by: Shivendra Kakrania <shiven@codeaurora.org>
Have a chipset specific check to decide the default value of
num of extradata planes. Make num of planes as 2 if
extradata is enabled.
Change-Id: Ie61cac744b4277c024f36bebe795bea2eeced6ae
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
