The SAP channel change can be called in scheduler thread and thus
waiting for hw mode change in scheduler thread will always lead to
timeout and thus channel switch failure.
Fix is to avoid wait and continue channel switch after hw mode
change is completed.
Change-Id: I951fab6c95ff2a84d6a619859295b830685fac4e
CRs-Fixed: 2484147
Bus bandwidth logic uses PLD_BUS_WIDTH_NONE to vote if the packet
threshold is less than bus_bw_low_threshold. The same vote is used for
system suspend too. Add a new state for bus bandwidth logic to vote for
idle state.
Change-Id: I62ca6fff84a01083001db360f56344a05fb955db
CRs-Fixed: 2484003
Currently the BLM removes the entry if the difference
between connect and disconnect is greater than the
blm bad bssid reset time.
This could lead to removal of those APs also which
are in rssi reject list too.
Fix is to remove the APs if not present in other list
other than avoid, black (driver).
Change-Id: Iae0edbd093546921e36ce4ed511450617e675adf
CRs-Fixed: 2485750
Currently, macro is used instead of destination size
to copy KEK pmo_gtk_req to kck and kek of
WMI_GTK_OFFLOAD_CMD_fixed_param.
Fix is to Copy KEK bytes from pmo_gtk_req same as the size of
cmd->kek i.e destination address to avoid macro change if size
of cmd->kck changes in future.
Change-Id: I06705f25682d950c35a3fb9bd0413ddf46e04ab4
CRs-Fixed: 2477212
In SAP mode when driver receives deauth and disassoc commands
for any sta, this command is getting queued in to sme command
queue in pending list with low priority, it means these
commands will be inserted at the tail of the queue. These
commands have timeout of 30 seconds. If any command is in active
list with high priority and higher timeout that command will not
let the deauth and disassoc commands to process and these commands
will get timeout. This will result in failure of disassoc and
deauth commands.
For example if driver operates in STA+SAP mode and sta issues
a connect request to some AP, in connect path driver tries to
move to single mac mode(SMM) and issues the command for the same.
SMM command is pushed in sme queue and now if SAP issues a
disconnect command for some connected station this command is
pushed after the SMM command. Since connection for STA is still
going on so SMM command does not process as it is waiting for
key. And wait-for-key timeout is around 120 seconds, SMM command
can not execute until wait-for-key timeout occures which results
timeout of the SAP issued disconnect command which is behind the
SMM command in the sme_command queue.
To resolve above issue change the priority of the disassoc and
deauth commands to high priority which will allow to push these
commands to the front of the sme_command queue and since these
comands does not wait for wait-for-key timeout, theses commands
will get a chance to execute.
Change-Id: I613bbd11b9172902dd8828fa04c778b4cfe6be14
CRs-Fixed: 2484608
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure and for this
target_if_mc_cp_stats_stats_event_handler is getting used.
Remove legacy implementation of stats event handler
wma_stats_event_handler and related APIs.
With this change remove unused structures also.
Change-Id: I9a892b5f7486a406654256fc2cc8177f2fafe790
CRs-Fixed: 2481937
Currently wlan_hdd_cfg80211_get_txpower is limited for STA
device. This causes issue when SAP device wants to get the
tx power.
Change-Id: Iadf34e6c74ba013247d925bcd4f05e1aa1a971c9
CRs-Fixed: 2481680
In function ol_target_failure(), if enable_self_recovery is true,
fw_indication_work_handler() will be called. Ramdump collection
will not be executed. But for no CNSS module platform, recovery flag
is neither cleaned, no any FW indication is sent to user space.
Even enable_self_recovery is false, no FW crashed indication sent
to user space.
So, call function ol_check_clean_recovery_flag() to clean recovery
flag, and send FW CRASHED indication to user space by function
ol_target_failure().
Change-Id: I44396caf4972dc267d60757c479e4681f8885de5
CRs-Fixed: 2482596
Firmware sends roam event with reason WMI_ROAM_REASON_DEAUTH when
it receives deauth/disassoc from the peer and fails to roam.
The event also carries deauth/disassoc frame.
A new param "notif_params1" is defined to carry length of the
frame and a new TLV element "deauth_disassoc_frame" to carry
the frame.
Extract IEs from the frame when the event is received and
send them to kernel through cfg80211_disconnected().
Change-Id: I14610136e5e9758403e48264d04d1655e4466d3c
CRs-Fixed: 2481915
AP may send IEs in deauth/disassoc frames as part of disconnection.
Extract the same and forward to kernel through
cfg80211_disconnected().
Change-Id: I4ef339dcd1ecff64d6bed1de35621ecce5d8030a
CRs-Fixed: 2481912
disconnect_ies sent from userspace are cached in vdev mgr object.
Send the same in deauth/disassoc frames initiated from the driver.
Free the IEs once the frame is sent out successfully.
Change-Id: Ib223a9da7f5795bc10d717efe23c6106391070bb
CRs-Fixed: 2481909
Application sends disconnect IEs to driver through vendor command
SET_WIFI_CONFIGURATION by embeding in the attribute
QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES. Extract the same and validate
to make sure it's not more than maximum IE length that can be
accomodated in deauth/disassoc frame. Cache the extracted IEs
in mlme vdev object.
Change-Id: I6c95aa1d4d8ef7d8ed3ad5be8832ef1f45c26a2f
CRs-Fixed: 2481908
Policy manager PCL list is invalid for SAP in case of
NAN Disc + STA case. As per design NAN will be disabled
internally in driver, resulting in STA+SAP concurrency.
Thus update Policy manager PCL tables for allowing SAP
in case of NAN Disc + STA concurrency mode.
Change-Id: I7480f662c287e38c7e71448384cff9738e94e3f7
CRs-fixed: 2480370
Currently both system and runtime PM resume are clearing
wow applicable flag and when runtime PM suspend and suspend
are happening in parallel wow applicable flag value is lost
and host is by mistake enabling pdev suspend instead of wow
suspend. Move the logic to clear wow applicable flag to suspend
configuration path such that every time when either runtime pm
or system suspend is enabled correct wow parameter is chosen.
Change-Id: I821dd5cd23493611dfc5a1c3ebf706defe785b6d
CRs-Fixed: 2475227
* changes:
Release 5.2.0.138N
qcacld-3.0: Add null check for qdf_ctx in hdd_configure_cds
qcacld-3.0: Add support to configure avoid acs freq list
qcacld-3.0: Remove redundant init and check in policy_mgr_skip_dfs_ch
qcacld-3.0: Advertise max BA buffer size in HE mode
FW version information which driver used to get
is updated to add release branch version also.
To give that information to userspace, parse the
release branch information also from the extended
FW version.
Change-ID: I45d06bac5ef0e57d1db8dbfe7ff6a0d7e2144b88
CRs-Fixed: 2482835
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure.
Remove legacy implementation for wow stats related apis
as part of cleanup.
Change-Id: Ib06d5bf0e11c8340f459185d18c076c295f39df5
CRs-Fixed: 2481927
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure.
Remove legacy implementation for get station stats api
as part of cleanup.
Change-Id: Iadc7fceccec32e7a27c29872fb13c03f79208965
CRs-Fixed: 2480770
While filling station info rx_mpdus and fcs_error count
are getting filled and corresponding flags are getting
set. These flags are set using BIT macro which operates
only on integers and will cause overflow on 32 bit
machine if the bit operation is of more than 32 bit.
To resolve above issue use BIT_ULL for bit operations
on station flags.
Change-ID: Ia7263f0e86a1fbdf477491b84bf94d5609781b00
CRs-Fixed: 2484159
