Recently aio_p{read,write} changed to perform retries internally rather
than returning -EIOCBRETRY. This inadvertantly resulted in always calling
aio_{read,write} with ki_left at 0 which would in turn immediately return
0. Harmless, but we can avoid this call by checking in the caller.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only one of the run or kick path is supposed to put an iocb on the run
list. If both of them do it than one of them can end up referencing a
freed iocb. The kick path could delete the task_list item from the wait
queue before getting the ctx_lock and putting the iocb on the run list.
The run path was testing the task_list item outside the lock so that it
could catch ki_retry methods that return -EIOCBRETRY *without* putting the
iocb on a wait queue and promising to call kick_iocb. This unlocked check
could then race with the kick path to cause both to try and put the iocb on
the run list.
The patch stops the run path from testing task_list by requring that any
ki_retry that returns -EIOCBRETRY *must* guarantee that kick_iocb() will be
called in the future. aio_p{read,write}, the only in-tree -EIOCBRETRY
users, are updated.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only one of the run or kick path is supposed to put an iocb on the run
list. If both of them do it than one of them can end up referencing a
freed iocb. The kick patch could set the Kicked bit before acquiring the
ctx_lock and putting the iocb on the run list. The run path, while holding
the ctx_lock, could see this partial kick and mistake it for a kick that
was deferred while it was doing work with the run_list NULLed out. It
would then race with the kick thread to add the iocb to the run list.
This patch moves the kick setting under the ctx_lock so that only one of
the kick or run path queues the iocb on the run list, as intended.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As requested by Thomas Gleixner <tglx@linutronix.de>:
"5d3d0f7704ed0bc7eaca0501eeae3e5da1ea6c87 breaks a couple of ARM
boards, which depend on the historical bootmem allocation order.
There is a cleaner solution around to remove the pgdat list
completely, but this is a topic for post 2.6.14
Andi signalled ACK already."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch updates the way SELinux classifies and handles IP
based protocols.
Currently, IP sockets are classified by SELinux as being either TCP, UDP
or 'Raw', the latter being a default for IP socket that is not TCP or UDP.
The classification code is out of date and uses only the socket type
parameter to socket(2) to determine the class of IP socket. So, any
socket created with SOCK_STREAM will be classified by SELinux as TCP, and
SOCK_DGRAM as UDP. Also, other socket types such as SOCK_SEQPACKET and
SOCK_DCCP are currently ignored by SELinux, which classifies them as
generic sockets, which means they don't even get basic IP level checking.
This patch changes the SELinux IP socket classification logic, so that
only an IPPROTO_IP protocol value passed to socket(2) classify the socket
as TCP or UDP. The patch also drops the check for SOCK_RAW and converts
it into a default, so that socket types like SOCK_DCCP and SOCK_SEQPACKET
are classified as SECCLASS_RAWIP_SOCKET (instead of generic sockets).
Note that protocol-specific support for SCTP, DCCP etc. is not addressed
here, we're just getting these protocols checked at the IP layer.
This fixes a reported problem where SCTP sockets were being recognized as
generic SELinux sockets yet still being passed in one case to an IP level
check, which then fails for generic sockets.
It will also fix bugs where any SOCK_STREAM socket is classified as TCP or
any SOCK_DGRAM socket is classified as UDP.
This patch also unifies the way IP sockets classes are determined in
selinux_socket_bind(), so we use the already calculated value instead of
trying to recalculate it.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I need the following patch to compile -git8 here, otherwise these
files fail to compile (asm/hw_irq.h needs definitions from
linux/irq.h and that file provides the required include ordering).
I did not do a full audit, though there looks to be many other
places that should get the same treatment, if this is the right
way to do it.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the free_irq() in USB suspend breaks resume on some setups where USB
(ohci/ehci) shares the interrupt with an other device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BUILD_BUG_ON(1) is asking for trouble (and getting it) when used in that
manner - dead code elimination happens after we parse it and invalid
type is invalid type, dead code or not.
It might be version-dependent, but at least 4.0.1 refuses to accept
that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switched cpuset_common_file_read() to simple_read_from_buffer(), killed
a bunch of useless (and not quite correct - e.g. min(size_t,ssize_t))
code.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Gen FUKATSU
Invalidate BTB entry instruction flushes two instruction
at a time. Therefore this instruction should be done four
times after invalidate instruction cache line.
Signed-off-by: Gen Fukatsu
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The warning is caused by the gic_set_cpu() function being defined but not
used if CONFIG_SMP is not defined.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
When CONFIG_CPU_CACHE_VIPT is defined, the flush_pfn_alias() function is
implicitely declared and it later conflicts with its actual definition.
This patch moves the function definition to the beginning of the file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- __user annotations
- NULL noise removal
- C99 initializers
- s/u32/pm_message_t/ in ->suspend()
- removal of bogus casts in iounmap() arguments
- if_mii() instead of open-coded variant
Remains to be done: ethtool conversion.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does a readl() on DEVICE_ID which is 2-byte aligned and
2-bytes in size. It's doing this read just to flush write buffers.
Create IN16() and OUT16() macros, and use the former to do this I/O
load.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Use cpudata cache line sizes, not magic constants.
2) Align start address in cheetah case so we do not get
unaligned address traps. (pgrep was good at triggering
this, via /proc/${pid}/cmdline accesses)
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete all of the code working with sp_banks[] and replace
with clean acquisition and sorting of physical memory
parameters from the firmware.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Handle better the case where the sender sends full sized
frames initially, then moves to a mode where it trickles
out small amounts of data at a time.
This known problem is even mentioned in the comments
above tcp_grow_window() in tcp_input.c, specifically:
...
* The scheme does not work when sender sends good segments opening
* window and then starts to feed us spagetti. But it should work
* in common situations. Otherwise, we have to rely on queue collapsing.
...
When the sender gives full sized frames, the "struct sk_buff" overhead
from each packet is small. So we'll advertize a larger window.
If the sender moves to a mode where small segments are sent, this
ratio becomes tilted to the other extreme and we start overrunning
the socket buffer space.
tcp_clamp_window() tries to address this, but it's clamping of
tp->window_clamp is a wee bit too aggressive for this particular case.
Fix confirmed by Ion Badulescu.
Signed-off-by: David S. Miller <davem@davemloft.net>
But retain the comment fix.
Alexey Kuznetsov has explained the situation as follows:
--------------------
I think the fix is incorrect. Look, the RFC function init_cwnd(mss) is
not continuous: f.e. for mss=1095 it needs initial window 1095*4, but
for mss=1096 it is 1096*3. We do not know exactly what mss sender used
for calculations. If we advertised 1096 (and calculate initial window
3*1096), the sender could limit it to some value < 1096 and then it
will need window his_mss*4 > 3*1096 to send initial burst.
See?
So, the honest function for inital rcv_wnd derived from
tcp_init_cwnd() is:
init_rcv_wnd(mss)=
min { init_cwnd(mss1)*mss1 for mss1 <= mss }
It is something sort of:
if (mss < 1096)
return mss*4;
if (mss < 1096*2)
return 1096*4;
return mss*2;
(I just scrablled a graph of piece of paper, it is difficult to see or
to explain without this)
I selected it differently giving more window than it is strictly
required. Initial receive window must be large enough to allow sender
following to the rfc (or just setting initial cwnd to 2) to send
initial burst. But besides that it is arbitrary, so I decided to give
slack space of one segment.
Actually, the logic was:
If mss is low/normal (<=ethernet), set window to receive more than
initial burst allowed by rfc under the worst conditions
i.e. mss*4. This gives slack space of 1 segment for ethernet frames.
For msses slighlty more than ethernet frame, take 3. Try to give slack
space of 1 frame again.
If mss is huge, force 2*mss. No slack space.
Value 1460*3 is really confusing. Minimal one is 1096*2, but besides
that it is an arbitrary value. It was meant to be ~4096. 1460*3 is
just the magic number from RFC, 1460*3 = 1095*4 is the magic :-), so
that I guess hands typed this themselves.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Daniel Jacobowitz
Thread flags are inherited on fork(). In order for a binary which has
the iWMMXt coprocessor enabled to run a binary which needs the FPA
emulation, we need to explicitly clear TIF_USING_IWMMXT if we are not
going to set it.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SMU driver has a small mistake in the locking of the interrupt code,
if polled access and interrupt access race, interrupt may take a lock
and return without releasing it. This fixes it. With that patch, the
driver is rock solid with my experimental thermal control (which bangs
it pretty hard) racing with real time clock and cpufreq handling.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
it seems that readv(2)/writev(2) syscalls do not call
file_permission callback. Looks like this is overlook.
I have filled the issue into redhat bugzilla as
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=169433
and got the recommendation to post this on lsm mailing list.
The following trivial patch solves the problem.
Signed-off-by: Kostik Belousov <kostikbel@gmail.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
The attempt to fixup the lockless mce log buffer introduced an infinite loop
when trying to find a free entry.
And:
Using rcu_dereference() to load mcelog.next doesn't seem to be sufficient
enough to ensure that mcelog.next is loaded each time around the loop in
mce_log(). Instead, use an explicit rmb() to ensure that the compiler gets it
right.
AK: turned the smp_wmbs into true wmbs to make sure they are not
reordered by the compiler on UP.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I checked with AMD and they requested to only disable it for family 15.
Also disable it for i386 too. And some style fixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Any tests using < TASK_STOPPED or the like are left over from the time
when the TASK_ZOMBIE and TASK_DEAD bits were in the same word, and it
served to check for "stopped or dead". I think this one in
do_signal_stop is the only such case. It has been buggy ever since
exit_state was separated, and isn't testing the exit_state value.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland points out that the flags end up having non-obvious dependencies
elsewhere, so revert aa55a08687 and add
some comments about why things are as they are.
We'll just have to fix up the broken comparisons. Roland has a patch.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_signal_stop:
for_each_thread(t) {
if (t->state < TASK_STOPPED)
++sig->group_stop_count;
}
However, TASK_NONINTERACTIVE > TASK_STOPPED, so this loop will not
count TASK_INTERRUPTIBLE | TASK_NONINTERACTIVE threads.
See also wait_task_stopped(), which checks ->state > TASK_STOPPED.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
[ We really probably should always use the appropriate bitmasks to test
task states, not do it like this. Using something like
#define TASK_RUNNABLE (TASK_RUNNING | TASK_INTERRUPTIBLE | \
TASK_UNINTERRUPTIBLE | TASK_NONINTERACTIVE)
and then doing "if (task->state & TASK_RUNNABLE)" or similar. But the
ordering of the task states is historical, and keeping the ordering
does make sense regardless. ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function s3c2410fb_activate_var does not return
a value, therefore it should be declared void.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Workaround for the ioremap patch that produces a blank display on some
chipsets
- Make hwcursor = 0 the default. The hardware cursor does not work with all
hardware.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- use nonseekable_open() instead of messing with
if (*ppos != file->f_pos)
return -EISPIPE
in ->write() (->read is NULL).
- trivial __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
