The correct macro name when a driver is built as a module is
CONFIG_*_MODULE instead of CONFIG_*_MODULES. This patch fixes
this in several places.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As well as moving all the device declarations to a single one in devices.c
this causes all platforms to register the I/O and interrupt resources for
the AC97 controller.
Cc: eric miao <eric.miao@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Jürgen Schindele <linux@schindele.name>
Cc: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mainstone has the primary I2C bus exposed for use on plugin modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is partial because mainstone's keypad is really special, some of
the keys like '1', '2', ... are actually connected to two row/column
juntions, thus pressing '1' is equivalent to pressing 'A' & 'H'.
This is really brain damanged since it makes distinguishing between
pressing '1' and multiple keys pressing of 'A' & 'H' difficult.
So these special keys are not supported for the time being.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NOTE: currently don't know if the key code of KEY_SUSPEND is fit for
such usage.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. the following code to configure PGSRx is no way portable and
intuitive:
- PGSR0 = 0x00008800;
- PGSR1 = 0x00000002;
- PGSR2 = 0x0001FC00;
- PGSR3 = 0x00001F81;
this is removed as low power state has already been encoded in
the pin configuration definitions.
Note: there is no specific reason for some of the GPIOs to drive
high in low power mode as indicated by the above setting, those
bits are ignored, and the result is validated to work.
2. the following code to configure GPIO wakeup is removed as this
is now totally handled by pxa2xx_mfp_config():
- PWER = 0xC0000002;
- PRER = 0x00000002;
- PFER = 0x00000002;
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux has framebuffer backlight support infrastructure which should
be used to expose backlight attributes. Mainstone should use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability to have pxafb use only certain fixed video modes
(selected on a per platform basis). This is useful on production
hardware such as the Zaurus cxx00 models where the valid modes are
known in advance and any other modes could result in hardware damage.
Following this, add support for the cxx00 QVGA mode. Mode information
is passed to the lcd_power call to allowing the panel drivers to
configure the display hardware accordingly (corgi_lcd already contains
the functionality for the cxx00 panel).
This mirrors the setup already used by w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The irgflags consolidation did conflict with the ARM to generic IRQ
conversion and was not applied for ARM. Fix it up.
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Steve Yang
MACHINE_START struct doesn't have any bootargs location for the
mainstone. Result is no kernel command args get passed; no serial driver
is selected for console and results in a silent boot failure.
Signed-off-by: Steve Yang <steve.yang@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
The mainstone board pcmcia interrupt have been enabled via setup_irq()
and the following socket check calls enable_irq again. Set the NOAUTOEN flag so the interrupt is not automatically enabled in setup_irq()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
PXA map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we wrap calls to
desc->handler() in an inline function, desc_handle_irq(). This
reduces the size of Thomas' patch since the changes become more
localised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Without this some devices fail to work again after a suspend event.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
PXA27x sleep fixes:
* set additional sleep/wakeup registers for Mainstone boards.
* move CKEN=0 to pxa25x-specific code; that value is harmful on pxa27x.
* save/restore additional registers, including some found necessary for
C5 processors and/or newer blob versions.
* enable future support of additional sleep modes for PXA27x (eg,
standby, deep sleep).
* split off cpu-specific sleep processing between pxa27x and pxa25x into
separate files (partly in preparation for additional sleep modes).
Includes fixes from David Burrage.
Signed-off-by: Todd Poynor
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
