Only write to hardware in SCI_OUT() if the register size is valid.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7722 serial ports all lack SCSPTR registers, so mark them as
nonexistent in the register table.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reset the transmitter and receiver when setting up early printk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Drain by waiting for all characters to be sent, and make sure to
wait a little bit after setting up the baud rate.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use sci_out() instead of ctrl_outw() for early printk setup code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add physical memory resources such as System RAM, Kernel code/data/bss
and reserved crash dump area to /proc/iomem. Same strategy as on x86.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Do like everyone else and have a struct resource for kernel bss.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Select smc91x bus width using platform data for se7722 now when the
smc91x header file is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Select smc91x bus width and irg flags using platform data for MigoR
now when the smc91x header file is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH_MPC1211 has been marked as BROKEN for some time.
Unless someone is working on reviving it now, I'd therefore suggest this
patch to remove it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We clobber %i1 as well as %i0 for these system calls,
because they give two return values.
Therefore, on error, we have to restore %i1 properly
or else the restart explodes since it uses the wrong
arguments.
This fixes glibc's nptl/tst-eintr1.c testcase.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm handing over maintainership to Jeff Kirsher and moving on
to other Linux/Open Source work within Intel. Good luck to Jeff ;)
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 22eecde2f9. Uli
reports that it breaks UML on x86-64 with the Fedora 8 gcc (gcc 4.1.2),
causing a crash on startup. See
http://marc.info/?l=linux-kernel&m=121011722806093&w=2
for a trace.
Reported-by: Ulrich Drepper <drepper@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We die because we forget to convert initrd_start and
initrd_end to virtual addresses.
Reported by Mikael Pettersson
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 33dcdac2df ("kill ->put_inode")
removed the final use of i_op->put_inode, but left the now totally
unused "op" variable in iput().
Get rid of it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix warning from pmd_bad() at bootup on a HIGHMEM64G HIGHPTE x86_32.
That came from 9fc34113f6 x86: debug pmd_bad();
but we understand now that the typecasting was wrong for PAE in the previous
version: pagetable pages above 4GB looked bad and stopped Arjan from booting.
And revert that cded932b75 x86: fix pmd_bad
and pud_bad to support huge pages. It was the wrong way round: we shouldn't
weaken every pmd_bad and pud_bad check to let huge pages slip through - in
part they check that we _don't_ have a huge page where it's not expected.
Put the x86 pmd_bad() and pud_bad() definitions back to what they have long
been: they can be improved (x86_32 should use PTE_MASK, to stop PAE thinking
junk in the upper word is good; and x86_64 should follow x86_32's stricter
comparison, to stop thinking any subset of required bits is good); but that
should be a later patch.
Fix Hans' good observation that follow_page() will never find pmd_huge()
because that would have already failed the pmd_bad test: test pmd_huge in
between the pmd_none and pmd_bad tests. Tighten x86's pmd_huge() check?
No, once it's a hugepage entry, it can get quite far from a good pmd: for
example, PROT_NONE leaves it with only ACCESSED of the KERN_PGTABLE bits.
However... though follow_page() contains this and another test for huge
pages, so it's nice to keep it working on them, where does it actually get
called on a huge page? get_user_pages() checks is_vm_hugetlb_page(vma) to
to call alternative hugetlb processing, as does unmap_vmas() and others.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Earlier-version-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fcntl_setlk()/close() race prevention has a subtle hole - we need to
make sure that if we *do* have an fcntl/close race on SMP box, the
access to descriptor table and inode->i_flock won't get reordered.
As it is, we get STORE inode->i_flock, LOAD descriptor table entry vs.
STORE descriptor table entry, LOAD inode->i_flock with not a single
lock in common on both sides. We do have BKL around the first STORE,
but check in locks_remove_posix() is outside of BKL and for a good
reason - we don't want BKL on common path of close(2).
Solution is to hold ->file_lock around fcheck() in there; that orders
us wrt removal from descriptor table that preceded locks_remove_posix()
on close path and we either come first (in which case eviction will be
handled by the close side) or we'll see the effect of close and do
eviction ourselves. Note that even though it's read-only access,
we do need ->file_lock here - rcu_read_lock() won't be enough to
order the things.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
And with that last patch to affs killing the last put_inode instance we
can finally, after many years of transition kill this racy and awkward
interface.
(It's kinda funny that even the description in
Documentation/filesystems/vfs.txt was entirely wrong..)
Also remove a very misleading comment above the defintion of
struct super_operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- remove affs_put_inode, so preallocations aren't discared unnecessarily
often.
- remove affs_drop_inode, it's called with a spinlock held, so it can't
use a mutex.
- make i_opencnt atomic
- avoid direct b_count manipulations
- a few allocation failure fixes, so that these are more gracefully
handled now.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (27 commits)
pata_atiixp: Don't disable
sata_inic162x: update intro comment, up the version and drop EXPERIMENTAL
sata_inic162x: add cardbus support
sata_inic162x: kill now unused SFF related stuff
sata_inic162x: use IDMA for ATAPI commands
sata_inic162x: use IDMA for non DMA ATA commands
sata_inic162x: kill now unused bmdma related stuff
sata_inic162x: use IDMA for ATA_PROT_DMA
sata_inic162x: update TF read handling
sata_inic162x: add / update constants
sata_inic162x: misc clean ups
sata_mv use hweight16() for bit counting (V2)
sata_mv NCQ-EH for FIS-based switching
sata_mv delayed eh handling
libata: export ata_eh_analyze_ncq_error
sata_mv new mv_port_intr function
sata_mv fix mv_host_intr bug for hc_irq_cause
sata_mv NCQ and SError fixes for mv_err_intr
sata_mv rearrange mv_config_fbs
sata_mv errata workaround for sata25 part 1
...
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex. At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.
The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.
Add checks to ata_generic and pata_acpi to pin ATIIXP devices. Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.
I'm indebted to David Gero for this. His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on
[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
