Fix
arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicate __cpuinit in smp.c. Already defined in init.h which is
already included.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Has been introduced for x86-64 at some point to save memory
in struct page, but has been obsolete for some time. Just
remove it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pfn_to_page really requires pfn_valid to be true now, no question.
Some people stumbled over it, but it was misleading and wrong.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code should deal with an additional empty zone, so fix up the
#error.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 traditionally had a 4GB DMA32 zone. Set the compatibility flag
to keep old drivers working.
For new drivers it would be better to use ZONE_DMA32 now.
Cc: tony.luck@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
This adds support for the Nvidia Geforce 7800 series of cards to the
nvidiafb framebuffer driver. All it does is add the PCI device id for
the 7800, 7800 GTX, 7800 GO, and 7800 GTX GO cards to the module device
table for the nvidiafb.ko driver, so that nvidiafb.ko will actually work
on these cards.
I also added the relevant PCI device ids to linux/pci_ids.h
I tested it on my 7800 GTX here and it works like a charm. I now can
get framebuffer support on this card! Woo hoo!! Nothing like 200x75 text
mode to make your eyes BLEED. ;)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit. With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000. Oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix some dprintk's so that NLM, NFS client, and RPC client compile
cleanly if CONFIG_SYSCTL is disabled.
Test plan:
Compile kernel with CONFIG_NFS enabled and CONFIG_SYSCTL disabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The sunrpc module should build properly even when CONFIG_SYSCTL is
disabled.
Reported by Jan-Benedict Glaw.
Test plan:
Compile kernel with CONFIG_NFS as a module and built-in, and CONFIG_SYSCTL
enabled and disabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that we have a method of dealing with delegation recalls, actually
enable the caching of posix and BSD locks.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Delegations allow us to cache posix and BSD locks, however when the
delegation is recalled, we need to "flush the cache" and send
the cached LOCK requests to the server.
This patch sets up the mechanism for doing so.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I missed this one... Any form of rename will result in a delegation
recall, so it is more efficient to return the one we hold before
trying the rename.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RFC 3530 states that for OPEN_DOWNGRADE "The share_access and share_deny
bits specified must be exactly equal to the union of the share_access and
share_deny bits specified for some subset of the OPENs in effect for
current openowner on the current file.
Setattr is currently violating the NFSv4 rules for OPEN_DOWNGRADE in that
it may cause a downgrade from OPEN4_SHARE_ACCESS_BOTH to
OPEN4_SHARE_ACCESS_WRITE despite the fact that there exists no open file
with O_WRONLY access mode.
Fix the problem by replacing nfs4_find_state() with a modified version of
nfs_find_open_context().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We must not remove the nfs4_state structure from the inode open lists
before we are in sequence lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
At header fixup time, it is not yet legal to ioremap() PCI
device registers, yet that is what this quirk code needs to
do.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not transfer remaining time slice to another cpu on process exit.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Nicolas Pitre
We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.
Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.
This patch is a quick fix to change that ordering for ARM. Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):
On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Jiang
This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.
Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
ARM processors that have pld instructions are not using those copy_user
implementation anymore. Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merged verison of ELF_CORE_COPY_REGS is basically the PPC64 version, with
a memset that came from PPC and a few types abstracted out into #defines. But
it's not _quite_ right.
The first problem is we calculate the number of registers with:
nregs = sizeof(struct pt_regs) / sizeof(ELF_GREG_TYPE)
For a 32-bit process on a 64-bit kernel that's bogus because the registers are
64 bits, but ELF_GREG_TYPE is u32, so nregs == 88 which is wrong.
The other problem is the memset, which assumes a struct pt_regs is smaller
than a struct elf_regs. For a 32-bit process on a 64-bit kernel that's false.
The fix is to calculate the number of regs using sizeof(unsigned long), which
should always be right, and just memset the whole damn thing _before_ copying
the registers in.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
