Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The class of the MPC5121 pci host bridge is PCI_CLASS_BRIDGE_OTHER
while other freescale host bridges have class set to
PCI_CLASS_PROCESSOR_POWERPC.
This patch makes fixup_hide_host_resource_fsl match
PCI_CLASS_BRIDGE_OTHER in addition to PCI_CLASS_PROCESSOR_POWERPC.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the standalone setup the board's CPLD disables the PCI internal
arbiter, thus any access to the PCI bus will hang the board.
The common way to disable particular devices in the device tree is to
put the "status" property with any value other than "ok" or "okay"
into the device node we want to disable.
So, when there is no PCI arbiter on the bus the u-boot adds status =
"broken (no arbiter)" property into the PCI controller's node, and so
marks the PCI controller as unavailable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifying user-selectable option in the qe_lib/Kconfig was a bad idea
because the qe_lib/Kconfig is included into the top level Kconfig, and
thus the QE_GPIO option appears at the top level menu.
This patch effectively moves the QE_GPIO option under the platform menu
instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The comment in the code was asking "Do we have to do this?", and according
to x86 and s390 the answer is no, the scheduler will do it before calling
the arch hook.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A single full sync (mb()) is requrired to order the mmio to the qirr reg
with the set or clear of the message word. However, test_and_clear_bit
has the effect of smp_mb() and we are not doing any other io from here,
so we don't need a mb per bit processed.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several printks were broken at word boundaries for line length. Some
even referred to old function names. Using __func__ and changing the
text slightly for the format allows these printk formats to fit on one
line.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It is physically per-cpu, and we want the irq layer to treat it that way.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EOI normally has the side effect of returning the cpu to the base
priority to recieve the next interrupt. This is actually controlled
by the top byte of the xirr register. When we are exiting the
kernel in kexec we must eoi the ipi for the next kernel because we
never return from the handler, but we want to leave interrupt
delivery blocked until the next kernel takes action.
Since the hardware ipi vector is fixed, its easiest to just do the
eoi explicitly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This factors out processors joining and unjoining the Global Interrupt
Queue into a separate function.
There is a bit of math to calculate the arguments to rtas to join
or leave the global interrupt queue, and a warning on failure
afterwards. Make a helper for the 3 callers.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We only need to check the ibm,interrupt-server#-size property once, not
once per global server and thread.
We can use !CONFIG_SMP cpu masks and hard_smp_processor_id() to avoid an ifdef.
Put the node when breaking out of the loop on lpar systems.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Trim unneeded includes from xics.c. We don't use signals or gfp
flags, we use only OF functions and don't need prom, and the 8259
is now handled by our caller.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The xirr is 32 bits in hardware, but the hypervisor requries the upper
bits of the register to be clear on the hcall. By changing the type
from signed to unsigned int we can drop masking it back to 32 bits.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that xics_update_irq_servers is called only from init and hotplug
code, it becomes possible to clean up the ordering of functions in the
file, grouping them but the interfaces they implement.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xics supports only one ipi per cpu, and expects software to use some
queue to know why the interrupt was sent. In Linux, we use a an array
of bitmaps indexed by cpu to identify the message. Currently the bits
are set in smp.c and decoded in xics.c, with the data structure in a
header file. Consolidate the code in xics.c similar to mpic and other
interrupt controllers.
Also, while making the the array static, the message word doesn't need
to be volatile as set_bit and test_clear_bit take care of it for us, and
put it under ifdef smp.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously the FDT header field boot_cpuid_phys wasn't actually used
on ppc32. Instead the physical boot cpuid was assumed to be 0 for
!CONFIG_SMP.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is an old workaround in the sysdev/Makefile for dealing
with arch/ppc vs. arch/powerpc compiles. This is no longer
needed as arch/ppc is dead.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The helper is factored out of of_get_gpio(). Will be used by the QE
pin multiplexing functions (they need to parse the gpios = <> too).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, every time we determine which irq server to use, we check if
default_server, which is the id of the bootcpu, is still online. But
default_server is a hardware cpu, not the logical cpu id needed to index
cpu_online_map.
Since the default server can only go offline during a cpu hotplug event,
explicitly check the default server and choose the new one when we move
irqs away from the cpu being offlined.
This has the added benefit of only needing the boot_cpuid to be updated
and not relying on the cpu being marked offline during migrate_irqs_away.
Also, since xics_update_irq_servers only reads device tree information, we
can call it before xics_init_host in xics_init_IRQ and then default_server
will always be valid when we can reach get_irq_server via the host ops.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When reciving an irq vector that does not have a linux mapping, the kernel
prints a message and calls RTAS to disable the irq source. Previously
the kernel did not EOI the interrupt, causing the source to think it is
still being processed by software. While this does add an additional
layer of protection against interrupt storms had RTAS failed to disable
the source, it also prevents the interrupt from working when a driver
later enables it. (We could alternatively send an EOI on startup, but
that strategy would likely fail on an emulated xics.)
All interrupts should be disabled when the kernel starts, but this can
be observed if a driver does not shutdown an interrupt in its reboot
hook before starting a new kernel with kexec.
Michael reports this can be reproduced trivially by banging the keyboard
while kexec'ing on a P5 LPAR: even though the hvc_console driver request's
the console irq later in boot, the console is non-functional because
we're receiving no console interrupts.
Reported-By: Michael Ellerman
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If there are multiple reserved memory blocks via lmb_reserve() that are
contiguous addresses and on different NUMA nodes we are losing track of which
address ranges to reserve in bootmem on which node. I discovered this
when I recently got to try 16GB huge pages on a system with more then 2 nodes.
When scanning the device tree in early boot we call lmb_reserve() with
the addresses of the 16G pages that we find so that the memory doesn't
get used for something else. For example the addresses for the pages
could be 4000000000, 4400000000, 4800000000, 4C00000000, etc - 8 pages,
one on each of eight nodes. In the lmb after all the pages have been
reserved it will look something like the following:
lmb_dump_all:
memory.cnt = 0x2
memory.size = 0x3e80000000
memory.region[0x0].base = 0x0
.size = 0x1e80000000
memory.region[0x1].base = 0x4000000000
.size = 0x2000000000
reserved.cnt = 0x5
reserved.size = 0x3e80000000
reserved.region[0x0].base = 0x0
.size = 0x7b5000
reserved.region[0x1].base = 0x2a00000
.size = 0x78c000
reserved.region[0x2].base = 0x328c000
.size = 0x43000
reserved.region[0x3].base = 0xf4e8000
.size = 0xb18000
reserved.region[0x4].base = 0x4000000000
.size = 0x2000000000
The reserved.region[0x4] contains the 16G pages. In
arch/powerpc/mm/num.c: do_init_bootmem() we loop through each of the
node numbers looking for the reserved regions that belong to the
particular node. It is not able to identify region 0x4 as being a part
of each of the 8 nodes. It is assuming that a reserved region is only
on a single node.
This patch takes out the reserved region loop from inside
the loop that goes over each node. It looks up the active region containing
the start of the reserved region. If it extends past that active region then
it adjusts the size and gets the next active region containing it.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compatible property values in the form linux,<modalias> is not documented
anywhere and using it leaks Linux implementation details into the device
tree data (which is bad). Remove support for compatible values of this
form.
If any platforms exist which depended on this code (and I don't know of
any), then they can be fixed up by adding legacy translations to the
lookup table in this file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 32-bit and 64-bit kernel_thread functions don't properly
propagate errors being returned by the clone syscall. (In the case of
error, the syscall exit code returns a positive errno in r3 and sets
the CR0[SO] bit.)
This patch fixes that by negating r3 if CR0[SO] is set after the syscall.
Signed-off-by: Josh Poimboeuf <jpoimboe@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Offset is unsigned and when an address isn't found in the vma map
vma_map_lookup() returns the vma physical address + 0x10000000.
vma_map_lookup used to return 0xffffffff on a failed lookup, but
a change was made to return the vma physical address + 0x10000000
There are two callers of vam_map_lookup: one of them correctly
deals with this new return value, but the other (below) did not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:
1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
is unsigned type, the check will be true for `-1'.
Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Testing hotplug memory remove has revealed that we can oops in
pseries_lmb_remove(). The incorrect shift causes a NULL pointer
dereference in the page_zone() inline routine.
I have only been able to reproduce the oops on kernels with large pages
enabled.
Tested on Power5 and Power6 with and without large pages enabled.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A mutex_unlock(&gang->aff_mutex) in spufs_create_context() is missing
in case spufs_context_open() fails. As a result, spu_create syscall
and spu_get_idle() may block.
This patch adds the mutex_unlock.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Andre Detsch <adetsch@br.ibm.com>
Currently, an empty spufs root inode has nlink count of 1. However,
the directory has two links; / -> spu and /spu/ -> .
This change increments the link count of the root inode in spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When manipulating 64-bit PCI addresses, the code would lose the
top 32-bit in a couple of places when shifting a pfn due to missing
type casting from the 32-bit pfn to a 64-bit resource before the
shift.
This breaks using newer X servers for example on 440 machines
with the PCI bus above 32-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
rtas_log_read() doesn't check file flags for O_NONBLOCK and blocks
non-blocking readers of /proc/ppc64/rtas/error_log when there is
no data available. This fixes it.
Also rtas_log_read() returns now with ENODATA to prevent suspending of
process in wait_event_interruptible() when logging facility was
switched off and log is already empty.
Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix various defconfigs for Freescale chip based boards to remove
CONFIG_PPC_PMAC or CONFIG_PPC_CHRP which crept in due to those
being default y
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc uses CONFIG_FORCE_MAX_ZONEORDER, and some things depend on it
being at least 10 when 64k pages are not configured (notably the dart
iommu code with CONFIG_PM). The defaults are fine, but when going from a
64K pages config to one without 64K pages, MAX_ORDER stays at 9 which is
too low for 4K pages.
This patch makes the Kconfig enforce at least the defaults.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A bug in my initial 64-bit hibernation code breaks it when using
page sizes that aren't 4K.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The variable statindex in send_request is never read, so remove it.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Documentation/powerpc/smp.txt is so outdated that it makes sense to just
remove it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 14cf11af6c ("powerpc: Merge enough to
start building in arch/powerpc.") unwired /proc/ppc_htab, and commit
917f0af9e5 ("powerpc: Remove arch/ppc and
include/asm-ppc") removed the rest of the /proc/ppc_htab support, but there are
still a few references left. Kill them for good.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 8b150478 ("ppc: make phys_mem_access_prot() work with pfns
instead of addresses") fixed page_is_ram() in arch/ppc to avoid overflow
for addresses above 4G on 32-bit kernels. However arch/powerpc's
page_is_ram() is missing the same fix -- it computes a physical address
by doing pfn << PAGE_SHIFT, which overflows if pfn corresponds to a page
above 4G.
In particular this causes pages above 4G to be mapped with the wrong
caching attribute; for example many ppc440-based SoCs have PCI space
above 4G, and mmap()ing MMIO space may end up with a mapping that has
caching enabled.
Fix this by working with the pfn and avoiding the conversion to
physical address that causes the overflow. This patch compares the
pfn to max_pfn, which is a semantic change from the old code -- that
code compared the physical address to high_memory, which corresponds
to max_low_pfn. However, I think that was is another bug, since
highmem pages are still RAM.
Reported-by: vb <vb@vsbe.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a .gitignore in arch/powerpc/kernel to ignore the generated
vmlinux.lds.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a defconfig for the AMCC Arches evaluation board
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH,
UART, EEPROM and temperature sensor, along with a shared debug port.
The two 460GT's will communicate with each other via shared memory,
Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the phy types found on the Arches and other
PowerPC 460 based boards.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch allows the 4xx (conventional) PCI bridge to be disabled
via the device tree. This is needed for 4xx PCI adapter hardware.
Use the PCI node's status property to disable the PCI bridge.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
