The PNP system board driver (drivers/pnp/system.c) contains all the
same functionality, so we don't need the ACPI version.
Previously, a motherboard device would be claimed by *both* the ACPI and
PNP drivers, resulting in stuff like this in /proc/ioports:
1200-121f : motherboard <-- from drivers/acpi/motherboard.c
1200-121f : pnp 00:0d <-- from drivers/pnp/system.c
Make sure to enable CONFIG_PNP (and CONFIG_PNPACPI) to include the
PNP system board driver.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I'm trying to remove drivers/acpi/motherboard.c, which is mostly
redundant with drivers/pnp/system.c. So make sure that we include the
PNP driver in the default config. Most distros enable this already.
Turning on CONFIG_PNP also causes the following options to be enabled:
CONFIG_PNPACPI
CONFIG_SERIAL_8250_PNP
CONFIG_SERIAL_8250_PNP causes legacy serial ports to be discovered
twice, which is ugly but harmless:
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Most x86 boxes have no iomem system board resources, but some ia64
boxes do.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Resources described by the FADT aren't really a good fit for the
ACPI motherboard driver.
The motherboard driver cares about PNP0C01 and PNP0C02 devices and
their resources.
The FADT describes some resources used by the ACPI core. Often, they
are also described by by the _CRS of a motherboard device, but I think
it's better to reserve them specifically in the ACPI osl.c because
(a) the motherboard driver is optional and ACPI uses the resources even
if the driver is absent, and (b) I want to remove the ACPI motherboard
driver because it's mostly redundant with the PNP system.c driver.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some of the ACPI devices use the internal fake hids
which are exposed to userspace as devces' bus_id after sysfs conversion.
To make it more friendly, we convert them to more understandable strings.
For those devices w/o PNPids, we use "device:instance_no" as the bus_id
instead of "PNPIDNON:instance_no".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=7695
Originally we converted bind/unbind to use a new pci bridge driver.
The driver will add/remove _PRT, so we can eventually remove
.bind/.unbind methods.
But we found that some of the _ADR-Based devices don't have _PRT,
i.e. they are not managed by the new ACPI PCI bridge driver.
So that .bind method is not called for some _ADR-Based devices,
which leads to a failure.
Now we make ACPI PCI Root Bridge Driver scan and binds all _ADR-Based devices
once the driver is loaded, in the .add method of ACPI PCI Root Bridge driver.
Extra code path for calling .bind/.unbind when _ADR-Based devices
are hot added/removed is also added.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously we used the device name in the DSDT, but would
crash upon encountering a duplicate. Also, exposing the
DSDT device name to the user in a patch isn't a good idea,
because it is arbitrary.
After some discussion, we finally decided to use
"PNPID:instance_no" as the bus_id of ACPI devices.
Two attributes for each device are added at the same time,
the full pathname in ACPI namespace and hardware_id if it has.
NOTE: acpi_bus_id_list is used to keep the information of PNPID
and instance number of the given PNPID. Loop the
acpi_bus_id_list to find the instance_no of the same PNPID
when register a device. If failed, i.e. we don't have a
node with this PNPID, allocate one and link it to this list.
NOTE: Now I don't take the memory free work in charge.
If necessary, I can add a reference count in
struct acpi_device_bus_id, and check the reference and
when unregister a device, i.e. memory is freed when
the reference count of a given PNPID is 0.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We do this mainly because:
1. hid is used to match ACPI devices and drivers.
.match method which is incompatible to driver model
can be deleted from acpi_driver.ops then.
2. As the .uevent method mark ACPI drivers by PNPID,
fake hid is set to non-PNPID devices so that udev script
can load the right ACPI driver by looking for
"HWID = " or "COMPTID = ".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_device had a .bind/.unbind methods, but Linux driver model does not.
Cut ACPI PCI code over to use the Linux driver model methods.
Convert bind/unbind to use a new pci bridge driver.
The driver will add/remove _PRT, so we can eventually
remove .bind/.unbind methods.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Consolidate motherboard1 and motherboard2 drivers into one
so that driver core doesn't complain that two drivers have
the same name.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add removal_type in structure acpi_device for hot removal.
ACPI_BUS_REMOVAL_EJECT is used for ACPI device hot removal.
Only one parameter is allowed in .remove method due to driver model.
So removal_type is added to indicate different removal type.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add acpi_bus_ops in acpi_device to support acpi hot plug.
NOTE: Two methods .add and .start in acpi_driver.ops are
called separately to probe ACPI devices, while only
.probe method is called in driver model.
As executing .add and .start separately is critical
for ACPI device hot plug, we use acpi_bus_ops to
distinguish different code path.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Setup new sysfs framework
1. Remove /sys/firmware/acpi
2. Add ACPI device in device tree.
File "eject" for every device that has _EJ0 method is moved from
/sys/firmware to /sys/devices.
Operation on this file is exactly the same as before.
i.e. echo 1 to "eject" will cause hot removal of this device.
Corresponding changes should be made in userspace for hot removal.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui<rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adjust link order to add ACPI devices to global list before PCI devices.
In addition, acpi_bus type must be initialized before any driver loads.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI device/driver registration Interfaces are modified
to follow Linux driver model.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add ACPI bus_type for Linux driver model.
1. .shutdown method is added into acpi_driver.ops
needed by bus_type operations.
2. remove useless parameter 'int state' in .resume method.
3. change parameter 'int state'
to 'pm_message_t state' in .suspend method.
Note: The new .uevent method mark ACPI drivers by PNPID instead of by name.
Udev script needs to look for "HWID=" or "COMPTID=" to load
ACPI drivers as a result.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add device_driver into acpi_driver for driver model.
Add helper functions 'to_acpi_device' and 'to_acpi_driver'
to get structure acpi_device/acpi_driver by device/device_driver.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We want the name 'to_acpi_device'.
And the current macro 'to_acpi_device' will be removed
after device model is setup.
So just simply rename them.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adjust the code and make code doing similar things together.
No logic changes.
Signed-off-by : Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the deferred hooks and all related code as scheduled in
feature-removal-schedule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib6_node 'subtree' depend on IPV6_SUBTREES.
Signed-off-by: Kim Nordlund <kim.nordlund@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in SCTP, we maintain a local address list by rebuilding the whole
list from the device list whenever we get a address add/delete event.
This patch fixes it by only adding/deleting the address for which we
receive the event.
Also removed the sctp_local_addr_lock() which is no longer needed as we
now use list_for_each_safe() to traverse this list. This fixes the bugs
in sctp_copy_laddrs_xxx() routines where we do copy_to_user() while
holding this lock.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should call tcp_free_md5sig_pool() not __tcp_free_md5sig_pool()
so that it does proper refcounting.
Signed-off-by: David S. Miller <davem@davemloft.net>
> Relevant standard (RFC 3493) notes:
>
> The IPV6_UNICAST_HOPS option may be used with getsockopt() to
> determine the hop limit value that the system will use for subsequent
> unicast packets sent via that socket.
>
> I don't reckon -1 could be the hop limit value.
-1 means un-initialized.
> IMHO, the value from
> case 1 (if socket is connected to some destination), otherwise case 2
> (if bound to a scope interface) or ultimately the default hop limit
> ought to be returned instead, as it will be most often correct, while
> the current behavior is always wrong, unless setsockopt() has been used
> first. I don't if some people may think doing a route lookup in
> getsockopt might be overly expensive, but at least the two other cases
> should be ok, particularly the last one.
The following patch seems to work for me, but this code has behaved this
way for a while, so don't know if it will break any existing apps.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a recent patch we introduced invalid return codes which will result in the
opposite of what is intended (i.e. send more packets in face of peculiar
network conditions).
This fixes it by returning ~0 which means not calculated as per
dccp_li_hist_calc_i_mean.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
If we come to node we'd already marked as seen and it's not a part of path
(i.e. we don't have a loop right there), we already know that it isn't a
part of any loop, so we don't need to revisit it.
That speeds the things up if some chain is refered to from several places
and kills O(exp(table size)) worst-case behaviour (without sleeping,
at that, so if you manage to self-LART that way, you are SOL for a long
time)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matches and targets verification is duplicated in normal and compat processing
ways. This patch refactors code in order to remove this.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLUSTERIP, CONNMARK, CONNSECMARK, and connbytes need ip_conntrack or
layer 3 protocol module of nf_conntrack.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To do that, this makes nf_ct_l3proto_try_module_{get,put} compatible
functions. As a result we can remove '#ifdef' surrounds and direct call of
need_conntrack().
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with INET=n results in
WARNING: "ip_route_output_key" [net/netfilter/nf_conntrack_h323.ko] undefined!
The entire code in net/netfilter is only used for IPv4/IPv6 currently, so
let it depend on INET.
Noticed by Toralf Förster <toralf.foerster@gmx.de>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4017/1: [Jornada7xx] - Updating Jornada720.c
[ARM] 3992/1: i.MX/MX1 CPU Frequency scaling support
[ARM] Provide a method to alter the control register
[ARM] 4016/1: prefetch macro is wrong wrt gcc's "delete-null-pointer-checks"
[ARM] Remove empty fixup function
[ARM] 4014/1: include drivers/hid/Kconfig
[ARM] 4013/1: clocksource driver for netx
[ARM] 4012/1: Clocksource for pxa
[ARM] Clean up ioremap code
[ARM] Unuse another Linux PTE bit
[ARM] Clean up KERNEL_RAM_ADDR
[ARM] Add sys_*at syscalls
[ARM] 4004/1: S3C24XX: UDC remove implict addition of VA to regs
[ARM] Formalise the ARMv6 processor name string
[ARM] Handle HWCAP_VFP in VFP support code
[ARM] 4011/1: AT91SAM9260: Fix compilation with NAND driver
[ARM] 4010/1: AT91SAM9260-EK board: Prepare for MACB Ethernet support
Deprecate the old "legacy" PM API, and more importantly default it to "n".
Virtually nothing in-tree uses it any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_device_add_data() makes a copy of the data that is given to it,
and thus the parameter can be const. This removes a warning when data
from get_property() on powerpc is handed to platform_device_add_data(),
as get_property() returns a const pointer.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function can be __init
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix file and directory removal in debugfs. Add inotify support for file removal.
The following scenario :
create dir a
create dir a/b
cd a/b (some process goes in cwd a/b)
rmdir a/b
rmdir a
fails due to the fact that "a" appears to be non empty. It is because
the "b" dentry is not deleted from "a" and still in use. The same
problem happens if "b" is a file. d_delete is nice enough to know when
it needs to unhash and free the dentry if nothing else is using it or,
if someone is using it, to remove it from the hash queues and wait for
it to be deleted when it has no users.
The nice side-effect of this fix is that it calls the file removal
notification.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct dentry count to handle creation errors.
This patch puts a dput at the file creation instead of the file removal :
lookup_one_len already returns a dentry with reference count of 1. Then,
the dget() in simple_mknod increments it when the dentry is associated
with a file. In a scenario where simple_create or simple_mkdir returns
an error, this would lead to an unwanted increment of the reference
counter, therefore making file removal impossible.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix error handling of file and directory creation in DebugFS.
The error path should release the file system because no _remove will be called
for this erroneous creation.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor coding style fixes along the way : 80 cols and a white space.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Class virtual directory is created as the need arises.
But it is not deleted when the class is unregistered.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Show the initialization state(live, coming, going) of the module:
$ cat /sys/module/usbcore/initstate
live
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* HP Jornada 720 uses epson 1356 chip for graphics. This chip is compatible with s1d13xxxfb driver.
* HP Jornada 720 uses a Microprocessor Control Unit to talk to various
hardware. We add it as a platform device in jornada720_init()
* We provide pm_suspend() to avoid unresolved symbols in apm.o. We are
unable to truly suspend now, hence the stub.
* Speaker/microphone enabling got removed because it will be placed in the alsa driver.
Signed-off-by: Filip Zyzniewski <(address hidden)>
Signed-off-by: Kristoffer Ericson <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IA64 is in a tiny minority providing these defines in pci.h.
Almost everyone else has them in scatterlist.h
Signed-off-by: Tony Luck <tony.luck@intel.com>
