Reads from an HPET register require a round trip to the south bridge and are
almost as slow as PCI reads. By caching the last value we've written to the
comparator register, we can eliminate all HPET reads from the fast path in the
emulated RTC interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that the RTC timer is in non-periodic mode; some stupid BIOS might
have initialized it to periodic mode.
Furthermore, don't set the SETVAL bit in the config register. This wouldn't
have any effect unless the timer was in period mode (which it isn't), and then
the actual timer frequency would be half that of the desired one because
incrementing the comparator in the interrupt handler would be done after the
hardware has already incremented it itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the emulated RTC interrupt is no longer needed, we better disable it;
otherwise, we get a spurious interrupt whenever the timer has rolled over and
reaches the same comparator value.
Having a superfluous interrupt every five minutes doesn't hurt much, but it's
bad style anyway. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for shared HPET interrupts.
The driver previously acknowledged interrupts for both edge and level
interrupts, but didn't actually allow a shared interrupt in the latter case.
We use a new per-timer flag to save whether the timer's interrupt might be
shared, and use it to do the processing required for level interrupts only if
necessary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was only the RTC hardware that restricted interrupt frequencies to a power
of two. There is no reason to take over this restriction into the HPET
driver, so remove the offending check.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes several reads of a timer's config register that serve no
purpose whatsoever.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The variable hpet_ntimer is never read, so remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 32-bit architectures, the multiplication in the argument for
hpet_time_div() often overflows. In the typical case of a 14.32 MHz timer,
this happens when the desired frequency exceeds 61 Hz.
To avoid this multiplication, we can precompute and store the hardware
timer frequency, instead of the period, in the device structure, which
leaves us with a simple division when computing the number of timer ticks.
As a side effect, this also removes a theoretical bug where the timer
interpolator's frequency would be computed as a 32-bit value even if the
HPET frequency is greater than 2^32 Hz (the HPET spec allows up to 10 GHz).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disallow setting an interrupt frequency of zero (which would result in a
division by zero), and disallow enabling the interrupt when the frequency
hasn't yet been set (which would use an interrupt period of zero).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Various whitespace fixes
- Use kzalloc()
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the Infineon TPM driver off pci device and makes it a pure pnp-driver.
It includes pnp-port validation and region requesting.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the nsc driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the atmel driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in support of moving away from the lpc bus pci_dev. The power
management prototypes used by platform drivers is different but the
functionality remains the same.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the tpm does not have it's own pci id we have been consuming the lpc
bus. This is not correct and causes problems to support non lpc bus chips.
This patch removes the dependency on pci_dev from tpm.c The subsequent patches
will stop the supported chips from registering as pci drivers.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in preparation of supporting chips that are not necessarily on
the lpc bus and thus are not accessed with inb's and outb's. The patch
replaces the call to get the chip's status in the tpm.c file with a vendor
specific status function. The patch also defines the function for each of the
current supported devices.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's nasty to set random drivers to default m because people who just press
enter on make oldconfig get these. Remove the default m
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simplify the UP (1 CPU) implementatin of set_cpus_allowed.
The one CPU is hardcoded to be cpu 0 - so just test for that bit, and avoid
having to pick up the cpu_online_map.
Also, unexport cpu_online_map: it was only needed for set_cpus_allowed().
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I made a patch that detects if libintl.h (needed for nls) is present on the
host system and if it's not, it nls support is disabled by providing
dummies for the used nls functions.
This way if there is nls support on the host system the *config targets
will build according to Arnaldo Carvalho de Melo's i18n modifications, else
it just uses the original English messages.
I have also made a bug report at kernel's bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=5501
And there is a discussion about this problem in Gentoo's bugzilla:
http://bugs.gentoo.org/show_bug.cgi?id=99810
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of (char *) casts removed in a previous cleanup patch in
lib/string.c:memmove() were actually useful, as they suppressed a couple of
warnings:
assignment discards qualifiers from pointer target type
Fix by declaring the local variable const in the first place, so casts
aren't needed to strip the const qualifier.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a filesystem passes an idiotic blocksize into bread(), __getblk_slow() will
warn and will return NULL. We have a report (from Hubert Tonneau
<hubert.tonneau@fullpliant.org>) of isofs_fill_super() doing this (passing in
a silly block size) against an unplugged CDROM drive.
But a couple of __getblk_slow() callers forgot to check for the NULL bh, hence
oops.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__MUTEX_INITIALIZER() has no users, and equates to the more commonly used
DECLARE_MUTEX(), thus making it pretty much redundant. Remove it for good.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver had incorrectly wrapped module_init(rp_init) in #ifdef MODULE,
so it worked only when compiled as a module.
Tested by Wolfgang Denk with this device:
00:0e.0 Communication controller: Comtrol Corporation RocketPort 8 port w/RJ11 connectors (rev 04)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 7000 [size=64]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change corrects an omission in posix_cpu_timer_schedule, so that it
correctly propagates the overrun calculation to where it will get reported
to the user.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a rewrite of the one submitted on October 1st, using modules
(http://marc.theaimsgroup.com/?l=linux-kernel&m=112819093522998&w=2).
This rewrite adds a tristate CONFIG_RCU_TORTURE_TEST, which enables an
intense torture test of the RCU infratructure. This is needed due to the
continued changes to the RCU infrastructure to accommodate dynamic ticks,
CPU hotplug, realtime, and so on. Most of the code is in a separate file
that is compiled only if the CONFIG variable is set. Documentation on how
to run the test and interpret the output is also included.
This code has been tested on i386 and ppc64, and an earlier version of the
code has received extensive testing on a number of architectures as part of
the PREEMPT_RT patchset.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a long-standing vgacon bug: characters with the bright bit
set were left on the screen and not blacked out. All I did was that I
lookuped up some examples on the net about setting the vga palette, and
added the call missing from the linux kernel, but included in all other
ones. It works for me.
You can test this by writing something with the bright set to the
console, for example:
echo -e "\e[1;31mhello there\e[0m"
and then wait for the console to blank itself (by default, after 10 mins
of inactivity), maybe making it faster using
setterm -blank 1
so you only have to wait 1 minute.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds tests for the return value of sb_getblk() in the ext2/3
filesystems. In fs/buffer.c it is stated that the getblk() function never
fails. However, it does can return NULL in some situations due to I/O
errors, which may lead us to NULL pointer dereferences
Signed-off-by: Glauber de Oliveira Costa <glommer@br.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
list_move(&inode->i_list, &inode_in_use);
} else {
list_move(&inode->i_list, &inode_unused);
+ inodes_stat.nr_unused++;
}
}
wake_up_inode(inode);
Are you sure the above diff is correct? It was added somewhere between
2.6.5 and 2.6.8. I think it's wrong.
The only way I can imagine the i_count to be zero in the above path, is
that I_WILL_FREE is set. And if I_WILL_FREE is set, then we must not
increase nr_unused. So I believe the above change is buggy and it will
definitely overstate the number of unused inodes and it should be backed
out.
Note that __writeback_single_inode before calling __sync_single_inode, can
drop the spinlock and we can have both the dirty and locked bitflags clear
here:
spin_unlock(&inode_lock);
__wait_on_inode(inode);
iput(inode);
XXXXXXX
spin_lock(&inode_lock);
}
use inode again here
a construct like the above makes zero sense from a reference counting
standpoint.
Either we don't ever use the inode again after the iput, or the
inode_lock should be taken _before_ executing the iput (i.e. a __iput
would be required). Taking the inode_lock after iput means the iget was
useless if we keep using the inode after the iput.
So the only chance the 2.6 was safe to call __writeback_single_inode
with the i_count == 0, is that I_WILL_FREE is set (I_WILL_FREE will
prevent the VM to free the inode in XXXXX).
Potentially calling the above iput with I_WILL_FREE was also wrong
because it would recurse in iput_final (the second mainline bug).
The below (untested) patch fixes the nr_unused accounting, avoids recursing
in iput when I_WILL_FREE is set and makes sure (with the BUG_ON) that we
don't corrupt memory and that all holders that don't set I_WILL_FREE, keeps
a reference on the inode!
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparse complains about every MODULE_PARM used in a module: warning: symbol
'__parm_foo' was not declared. Should it be static?
The fix is to split declaration and initialization. While MODULE_PARM is
obsolete, it's not something sparse should report.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They aren't used anywhere in that file.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because people can play games reprogramming keys and leaving traps for the
next user of the console.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert existing function docs to kernel-doc format. Eliminate all
kernel-doc warnings. Fix some doc typos and a little whitespace cleanup.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ioctl doesn't exist for native i386.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix warnings from sparse due to un-declared functions that should either
have a header file or have been declared static
fs/ext2/bitmap.c:14:15: warning: symbol 'ext2_count_free' was not declared. Should it be static?
fs/ext2/namei.c:92:15: warning: symbol 'ext2_get_parent' was not declared. Should it be static?
fs/ext3/bitmap.c:15:15: warning: symbol 'ext3_count_free' was not declared. Should it be static?
fs/ext3/namei.c:1013:15: warning: symbol 'ext3_get_parent' was not declared. Should it be static?
fs/ext3/xattr.c:214:1: warning: symbol 'ext3_xattr_block_get' was not declared. Should it be static?
fs/ext3/xattr.c:358:1: warning: symbol 'ext3_xattr_block_list' was not declared. Should it be static?
fs/ext3/xattr.c:630:1: warning: symbol 'ext3_xattr_block_find' was not declared. Should it be static?
fs/ext3/xattr.c:863:1: warning: symbol 'ext3_xattr_ibody_find' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
de_thread() sends SIGKILL to all sub-threads and waits them to die in 'D'
state. It is possible that one of the threads already dequeued coredump
signal. When de_thread() unlocks ->sighand->lock that thread can enter
do_coredump()->coredump_wait() and cause a deadlock.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added a Receive_Abort to the Marvell serial driver
Fix occasional input overrun errors on Marvell serial driver
- If the Marvell serial driver is repeatedly started and then stopped it
will occasionally report an input overrun error when started.
- Added a Receive_Abort to the Marvell serial driver to abort previously
received receive errors when re-starting the receive
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Carlos Sanchez <csanchez@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Setting ctime is implicit in all setattr cases, so the FATTR_CTIME
definition is unnecessary.
It is used by neither the kernel nor by userspace.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct some typos and inconsistent use of "initialise" vs "initialize" in
comments. Reported by Ioannis Barkas.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix-up the CONFIG_FRAME_POINTER help text language a bit.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Back about a year ago when I last fiddled heavily with the do_wait code, I
was thinking too hard about the wrong thing and I now think I introduced a
bug whose inverse thought I was fixing.
Apparently noone was looking too hard over much shoulder, so as to cite my
bogus reasoning at the time. In the race condition when PTRACE_ATTACH is
about to steal a child and then the child hits a tracing event (what
my_ptrace_child checks for), the real parent does need to set its flag
noting it has some eligible live children. Otherwise a spurious ECHILD
error is possible, since the child in question is not yet on the
ptrace_children list.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
