I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as856) attempts to improve the performance of uhci-hcd by
removing the asynchronous skeleton Queue Headers. They don't contain
any useful information but the controller has to read through them at
least once every millisecond, incurring a non-zero DMA overhead.
Now all the asynchronous queues are combined, along with the period-1
interrupt queue, into a single list with a single skeleton QH. The
start of the low-speed control, full-speed control, and bulk sublists
is determined by linear search. Since there should rarely be more
than a couple of QHs in the list, the searches should incur a much
smaller total load than keeping the skeleton QHs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as855) adds some convenience macros to uhci-hcd, to help
simplify the code for computing hardware DMA pointers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a driver for the Davicom DM9601 USB 1.1 10/100Mbps
ethernet adaptor using the usbnet framework.
See http://www.davicom.com.tw/eng/products/dm9601.htm for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the JVC-PRX1 port replicator. Additionally cleans up
the tabs on a few of other IDs in the list.
Reported by: Reuben Thomas <rrt@sc3d.org>
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mon_bin_exit() and mon_text_exit() are called from __init code, so don't mark
them as __exit.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds all of the known Option device ids to the driver.
Many thanks to some Option engineers for getting me this list.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have two tables with the same device ids in it.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] One line missing from previous commit
[CIFS] mtime bounces from local to remote when cifs nocmtime i_flags overwritten
[CIFS] fix &&/& typo in cifs_setattr()
This reverts commit d2ed16356f.
As Thomas Gleixner reports:
"e1000 is not working anymore. ifup fails permanentely.
ADDRCONF(NETDEV_UP): eth0: link is not ready
nothing else"
The broken commit was identified with "git bisect".
Auke Kok says:
"I think we need to drop this now. The report that says that this
*fixes* something might have been on regular interrupts only. I
currently suspect that it breaks all MSI interrupts, which would make
sense if I look a the code. Very bad indeed."
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not only was the function way too big to be inlined in the first place,
it was used before it was even defined.
Noted-by: Faik Uygur <faik@pardus.org.tr>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In function 'qt1010_init':
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The result of copy_to_user was not used, so the compiler complained
now a warning will be issued if copy_to_user fails.
Signed-off-by: Marcel Siegert <mws@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enable BER/UNC counting for the stv0297 frontend.
The idea for this patch comes from stv0297_cs.c.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 00c4cc6751 Oliver Endriss changed
the budget-ci driver to use interrupt mode for i2c transfers.
This also meant that a new bunch of IR bytes that were previously lost
are now received, which allowed me to better understand how the MSP430
chip works. Unfortunately it also means that the current driver gets
some assumptions wrong and might generate double keypresses for one IR
command.
The attached patch fixes this by throwing away the repeat bytes and by
associating the correct command and device bytes.
Signed-off-by: David Hrdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Arjan van de Ven <arjan@infradead.org> reported an illegal re-usage of
the fileoperations struct if more than one dvb device (e.g. frontend) is
present.
This patch fixes this issue.
It allocates a new fileoperations struct each time a device is
registered and copies the default template fileops.
Signed-off-by: Marcel Siegert <mws@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The work item function is dvb_usb_read_remote_control():
INIT_WORK(&d->rc_query_work, dvb_usb_read_remote_control, d);
and the last piece of work it does is:
schedule_delayed_work(&d->rc_query_work,msecs_to_jiffies(d->props.rc_interval));
Hence you need to call "cancel_rearming_delayed_work()" and not
"cancel_delayed_work()", correct? I certainly haven't seen this oops
reoccur since I applied this patch.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds calls to i2c_gate_ctrl in the qt1010 dvb tuner module,
while removing the temporary hack in au6610 and gl861.
Tested successfully against fi-Oulu frequencies with
MSI Megasky 580 GL861 and Sigmatek DVB-110 AU6610.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
gl861: (MSI Megasky)
- hack for enable ZL10353 / QT1010 I2C gate
- use new QT1010 module instead of old code
au6610: (Sigmatek DVB-110)
- hack for enable ZL10353 / QT1010 I2C gate
- use new QT1010 module instead of old code
Tested successfully with au6610 and gl861 devices against fi-Yllas
frequencies. Now it locks perfectly with both devices.
There is a "hack" to enable probable i2c gate in zl10535
demodulator. QT1010 doesn't respond to any i2c messages before we
write 0x1a to demodulator register 0x62. In my understanding this
should be fixed to demodulator code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based
on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353)
demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar
as used in MSI Megasky GL861.
Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is
also supported by hw but I cannot test it due to lack of USB 1.1 port. Device
supports only isochronous mode transfers. There is also eeprom in usb
controller(at least in address range 0x80 - 0xbf) for storing data, eg.
firmware. Anyway, firmware loading is not used / required by the device.
There seems to be at least one unknown I2C device in address 0xa0, probably
remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07
from this unknown address.
Driver is based on gl861 module. Tuner has a lot of problems to lock with
megasky qt1010 module with this hardware with some broadcasting standards.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use parallel_ts - Now this driver works.
- correct typo in MODULE_VERSION
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove unneeded declaration of .generic_bulk_ctrl_endpoint
generic_bulk_ctrl_endpoint isn't being used in this device, so this
is not needed here.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky 580 based on gl861 has three endpoints:
- 0x81 BULK/ISOC IN MPEG2 TS
- 0x83 INT IN remote control receiver
- 0x02 BULK OUT bulk control endpoint
It doesn't look like the bulk endpoint is used, but better to
have the correct one in the config.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the DVB_USB_IS_AN_I2C_ADAPTER flag from the adapter
properties to the device properties.
Without this patch I get an OOPS when the gl861 driver tries to
access any registers.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gl861_tuner_attach function is not specific to this device.
This patch removes gl861_tuner_attach, and replaces it with
qt1010_tuner_attach from the qt1010 header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename driver_name from "gl861" to "dvb_usb_gl861"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The author's email address is already in the MODULE_AUTHOR field.
This patch adds his name as well.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the descriptions of "discovered" registers on the zl10353, using the
equivalaent mt352 register names.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement trl nominal rate calculation to Zarlink ZL10353 demod,
based on calculation used in Zarlink MT352.
This adds support for 6 and 8MHz bandwidth transponders.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement I2C gate control for Megasky GL861 and SigmaTek AU6610 support.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After studying many hours worth of register dumps of MT352 and ZL10353 fed
with identically damaged RF signals I have made an educated guess at which
registers contain the AGC level, bit error rate and uncorrectable error
count values.
Implement the IOCTLs that return these values to userspace.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver previously rejected encoder firmware whose size was
not a multiple of 8192. But this is a false check because it's
possible to find cx23416 firmware whose size doesn't conform to this
limit. So change the firmware loader implementation to be more
forgiving of the image size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
avoid double-up(), pointed out by Oliver.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb kernel_thread to kthread API port.
It is running fine here, including module load/unload and software suspend
(which doesn't work as expected with or without this patch :).
I didn't convert the dvb_ca_en50221 as I do not have such an interface, but
if the conversion process is fine with the v4l-dvb maintainers, it should not
be a problem to send a patch for that too ...
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- usb alternate selection modified to get the biggest endpoint packet size.
- fix sysfs get values for brightness/contrast/hue/saturation
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
