Clear sae_single_pmk info while processing del/flush pmk command
from supplicant, if required.
Change-Id: Idd974822ef0426461cd9971e54d8244d64b246b5
CRs-Fixed: 2616036
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should Set new flag in 11i
params during RSO start/update when initial connection is
completed based on the VSIE in AP beacon/probe response
frame. This flag will allow fw to roam to AP(s) which has
VSIE with single PMK.
Update PMK info in RSO start command with
sae_single_pmk info if initial connection is completed
with AP contains VSIE.
Change-Id: I839b48da48f92f24444e69405d87560186d7f986
CRs-Fixed: 2616029
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should:
1. Set new flag in 11i params during RSO start/update when
initial connection is completed based on the VSIE in AP
beacon/probe response frame. This flag will allow fw to roam
to AP(s) which has VSIE with single PMK.
2. STA should dynamically enable this feature if below
vendor specific IE on AP’s Beacon or Probe Response at
the first connection:
Category Data
Type 0xDD
Length 0x05
OUI 0x00 40 96
Type 0x03
Data Don’t care
(EX, 0x05)
Maintain a separate pmk information structure to support sae
roaming using single pmk.
Change-Id: I0aac7659cecd4d8aaff86c9715e512cf46f22615
CRs-Fixed: 2616035
AP isolation a.k.a intra-bss forwarding is a per AP attribute. Issue in
current IPA implementation is that it does not support per AP control.
In a SAP-SAP configuration, latter SAP configuration will always overwrite
first SAP's isolation configuration.
Fix is to add vdev id parameter from protocol layer so that IPA component
could configure AP isolation on a per AP basis.
Change-Id: I9c96cdcda03eb10b4c2984a757e52d77b5bf6790
CRs-Fixed: 2624757
Currently the TDLS module prints the peer info
every defined time interval which leads to too
much of information even when no rx tx is
ongoing with the peer which leads to excessive
logging.
Fix is to limit the logs and print only when there
is activity going on.
Change-Id: I6c1bf5a1ce8a858dfe895168178154a6c8b49c1f
CRs-Fixed: 2625632
Optimize logs after connect complete i.e roam offload params
and tdls state etc.
Change-Id: I5df7eb236ef1c7369f4d996c4f0eda7225652f12
CRs-Fixed: 2627694
Userspace expects the assoc request IEs of a disconnected station
to derive 11kv capabilities. Send the same in STA_INFO as part
of remote station info.
Change-Id: Iab5f39de833cd06e814e83f0149a0d21caf59b9f
CRs-Fixed: 2624922
Introduce a compile time flag SAE_SINGLE_PMK and new INI
"sae_same_pmk_feature_enabled" to enable/disable SAE
Roaming with same PMK/PMKID feature.
Change-Id: Ifca8ec8bcf6e9a2f1d8409b35390bfee0033bd30
CRs-Fixed: 2616025
FTM time sync feature is triggered when connection takes place
in case of STA and bss starts in case of SAP. The feature is
stopped when STA disconnects and bss stops.
Change-Id: I963b0134b7432c9827c2fb3d9dce7c81a8666d4d
CRs-Fixed: 2621144
Add ini config required for FTM time sync feature.
"enable_time_sync_ftm"- ini to enable/disable the feature.
"time_sync_ftm_mode" - ini to configure the burst/aggregated mode.
In burst mode the offset derived for each RTT frame is sent by
firmware, in aggregated mode only one offset is sent by firmware.
"time_sync_ftm_role" - ini to configure slave(STA)/master(SAP) role.
Change-Id: I6a06d6fdc4c7556c32ab2d28f1cbaa936b98a85b
CRs-Fixed: 2618654
Register tx and rx ops to send packet capture mode command and
to receive mgmt offload handler for packet capture component.
Change-Id: I70da00feff29399b98c5916eec17e26b62285db3
CRs-Fixed: 2619321
If resume and fw wakeup happens at the same time.
psoc_ctx->lock maybe doing bottom half operation for resume,
then wakeup interrupt comes on same cpu, the interrupt
handler will also acquire psoc_ctx->lock in
pmo_core_update_wow_initial_wake_up, which cause dead lock.
Using atomic for wow_initial_wake_up, so the interrupt handler
can avoid using spin_lock.
Change-Id: Id0e963a0924415e9660c57a1c1b776d3e609213d
CRs-Fixed: 2624899
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: Icbf8f4ed05a7bd181a076d526dd2e01d70be6b05
CRs-Fixed: 2618835
Enhance logs in policy mgr module to remove duplicate
or unwanted prints and keep only useful logs to debug.
Change-Id: Ifd585256955aceec29286d82838be0c588228c32
CRs-Fixed: 2614763
Process management Tx and Rx frames for packet capture mode
and post frames to the mon thread.
Change-Id: I14c0a1cf8a8aa4d4a4e16ad6200715b875611c81
CRs-Fixed: 2619317
Send vdev param command to FW for STA vdev to set the packet
capture mode. Send the command only if packet capture support
is enabled.
Change-Id: Ifed2431882b1f7d2869771e812daa5bcd5dc17e9
CRs-Fixed: 2619314
During CU and low rssi based roam triggers, consider AP as roam candidate
only if its roam score is better than connected AP score by at least
min_roam_score_delta.
User configures this candidate minimum roam score delta value using
"min_roam_score_delta" INI. User can set candidate minimum score delta
value between 0 to 10000 and default value is 1850.
Firmware will trigger roaming only if roam score of candidate AP is
greater than "min_roam_score_delta" & "roam_score_delta" values of
connected AP.
Change-Id: I180e769b5629aa405dbd89ed73e39e228adf92db
CRS-Fixed: 2614117
Add the function to parse the FTM timesync start/stop and offset
events received from target and populate them in ftm timsync
priv vdev structure.
Change-Id: Ibdcf97bb0a04fc6490c6bd2c26701036df92c5d4
CRs-Fixed: 2618646
Currently, host driver sends disconnect reason code as UNSPECIFIED
to kernel in most of the disconnection scenarios. Correct the same
to send proper reason code received from peer in case of peer
initiated disconnections.
Introduce new reason codes for internal disconnections and assign
proper reason code for each possible disconnect scenario.
Change-Id: I99bf4573b59dc810e0a1529fcd48061d10acae4e
CRs-Fixed: 2622310
Scan cmd still can be exist after scheduler thread is suspended
when host suspend, the scan cmd can't be removed from
serialization list by either complete or cancel any more since
both depends on scheduler thread, suspend thread blocked 30s to
wait scan cmd cleared.
Roam sync event from F/W can't be handled and Roam sync complete
can't be sent to F/W since scheduler thread suspended, then F/W
assert for roam sync cmd timeout.
After receive F/W down event, host will try SSR, but blocked by
unfinished suspend thread too.
Fix: suspend all components including scan before suspend
scheduler thread, make sure scan cmd is cleared and no new scan
is allowed any more before scheduler thread suspended.
Change-Id: I7a3badeedea018e4d92bbe8660692e42923852aa
CRs-Fixed: 2620650
Move disconnect ie info to a structure (wlan_disconnect_info)
and use it in mlme_legacy_priv. This helps to enhance the
structure further.
Change-Id: Id16e7eeb45a3f4c2fefac297f6730baf6b9e8991
CRs-Fixed: 2621149
Currently, when WWAN channel changes, the list of WLAN channels that
needs to be avoided is given to WLAN FW. WLAN FW indicates the list
to host. Upon receiving Channel avoidance indication, host switches
the operating-channel of SAP (if any and conflicting).
When there is a frequent channel change from WWAN side, it causes
frequent SAP disconnection. To mitigate this problem, as part of
this change send the configuration to the WLAN FW which delays
the channel avoidance indication before sending it to host.
Change-Id: If67775d59b9f61d3592a5f6609d3b002899e5daf
CRs-Fixed: 2615917
Optimize logs while sending assoc req and assoc rsp handling
frame by dumping the assoc req frame and not printing each
params separately. Also avoid multiple dump of same frame.
Change-Id: Ibcf2d9aa8de292b9b9f4b4c6a53a0f694d69475c
CRs-Fixed: 2619553
Currently there are lot of duplicate logging. Identify and
reduce those logs that are not absolutely necessary.
Change-Id: Ia2df5a46610b885be5e27455aef7f7281c7c3c55
CRs-Fixed: 2617719
Add INI parameter for packet capture mode
"packet_capture_mode" - ini to set packet capture mode.
Change-Id: Ie60c142af753c65b44aa0018440e43a215e51a27
CRs-Fixed: 2614578
idle_roam_rssi_delta - This threshold is the criteria to decide whether
DUT is idle or moving. If rssi delta is more than configured thresold
then its considered as not idle. RSSI delta is entered in dBm. Idle
roaming can be triggered if the connected AP rssi change exceeds or
falls below the rssi delta and if other criteria of ini
"enable_idle_roam" is met.
To enhance idle roaming, idle_roam_rssi_delta default value is changed
to 3.
Change-Id: I9a5b06081d59d8502c40df0485c2b997cbcb2b80
CRs-Fixed: 2619436
AP has less keep alive timer than STA, so AP is kicking out the STA and
sending the deauth.
To resolve this change CFG_INFRA_STA_KEEP_ALIVE_PERIOD_DEFAULT value from
60 to 30.
Change-Id: I0522071bc634b029178de6e09c11d237351a334d
CRs-Fixed: 2616279
When application issues NDP end to terminate an NDP connection,
host driver sends a request to the firmware and firmware
terminates the NDP by sending NDP end frame to the peer.
Currently, driver returns immediately after posting request to
the firmware. Application might issue NDI delete immediately
after returning from NDP_END request.
But firmware might take some time to complete the NDP termination
and send NDP_END indication to driver.
When driver tries to delete the NDI before receiving NDP_END
indication from firmware, it causes inconsistency in firmware as
the NDI on which the NDP is parked is freed.
So, wait till the NDP_END indication comes from
firmware(or timeout happens) before returning from ndp_end request
context.
Change-Id: Ied7ed36451ef007e38f67d48c54290b9dd674f54
CRs-Fixed: 2616018
Currently there is no inis for NAN component:
1. To configure the keep alive period for the
NDI interface.
2. To enable/disable discovery of NAN cluster with
Master Preference (MP) as 0 when a new device is
enabling NAN.
Add ini support to configure above mentioned values.
Change-Id: I47b67eb89fb8849960a9f492d2909e45b96308f3
CRs-Fixed: 2617839
This patchset adds the FTM TIME SYNC component in
target_if to register the ftm time sync wmi events/cmds.
Change-Id: I4ea14266a912c9d261a67809556774860b5ddab1
CRs-Fixed: 2617055
Currently there are lot of duplicate logging. Identify and
reduce those logs that are not absolutely necessary.
Change-Id: I649ce3bec8c3c8542fe9edd08907da9ab01fa948
CRs-Fixed: 2617504
Add support to customize DSCP-to-UP map table and send the
customized map values to FW to update its corresponding
map table.
Change-Id: Ibe9704a90468c898dd2e60fdf83a271152f654ce
CRs-Fixed: 2616247
In case of successful wow enable ack from FW for system
suspend call cdp wow ack response process, so that dp
layer will take care of required operations before system
goes to suspend.
Change-Id: Ibc5bf8d62aa055c9c8c7242c00abc3b696bb0051
CRs-Fixed: 2608980
