Fix some whitespace issues
Reorganise parisc_device probe routine to be a little less convoluted
Use ->hpa.start instead of ->hpa
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Neaten up the CONFIG_PA20 ifdefs
More merge fixes, this time for SMP
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Prettify the CONFIG_DEBUG_SPINLOCK __SPIN_LOCK_UNLOCKED initializers.
Clean up some warnings with CONFIG_DEBUG_SPINLOCK enabled.
Fix build with spinlock debugging turned on. Patch is cleaner like this,
too.
Remove mandatory 16-byte alignment requirement on PA2.0 processors by
using the ldcw,CO completer. Provides a nice insn savings.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
move pa_tlb_lock and it's primary consumers to tlb_flush.h
Future step will be to move spinlock_t definition out of system.h.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc4-pa3 : first pass at making sure use of RFI conforms to
PA 2.0 arch pages F-4 and F-5, PA 1.1 Arch page 3-19 and 3-20.
The discussion revolves around all the rules for clearing PSW Q-bit.
The hard part is meeting all the rules for "relied upon translation".
.align directive is used to guarantee the critical sequence ends more than
8 instructions (32 bytes) from the end of page.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
add || STI_CONSOLE to some of the basic FONTs. May need to get at
least one of them to default to "Y" for parisc.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix card-mode Dino crashes on 725 (and probably other Snake) systems.
Dino was coming up in fatal mode after a warm reboot. Resetting Dino
brings it out of fatal mode, so do that if the status register indicates
we're in fatal mode. Since this was never observed on any later systems,
I presume firmware does this for us on those.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Add debug statements in the cfg_read and cfg_write functions
Fix debug statements from the IRQ overhaul last winter
Rename dino_driver_callback() to dino_probe()
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 fdc/lci should be %r0 instead 0 for index (PA 1.1 compliance)
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Explain why we need insert_resource() instead of request_resource().
Fundementally, this is more convoluted for ccio driver because of
o legacy (HP-PB) transperant bridges.
o support for MMIO behind card-mode Dino (PCI)
o support for above bridges without ccio in the box
SBA driver doesn't have to worry about those issues.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Use insert_resource instead of request_resource now that the subdevices
will already have their resources claimed
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
re-enable use of "inline" for perf critical functions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa5 fix sign extension of MMIO range
Fixes the problem of claiming a range that is disabled on 64-bit kernel:
ccio_init_resource() claimed CCIO bus address space (ffffffff00000000,
ffffffffffffffff)
also removes use of __FILE__.
Tested on both 32 and 64-bit systems by Joel.
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc1-pa7 incorrect BUG_ON in ccio
ccio-dma.c line 1317 was preventing K-class with 4GB RAM from booting.
Any ccio machine with >=2GB of RAM would have (incorrectly) triggered this.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Convert to ioremap and __raw_read/write
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 move "sync" outside the main loop that fills IO Pdir.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove explicit use of sr0 in fdc ops.
Thanks to Joel Soete for reminding me were I added those...
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa2 - make SBA more anal about invalidating pdir entries
Previous code cleared the valid flag a pdir entry but it did NOT
guarantee this change was visible to the PDIR before writing
the PCOM register. Ie the SBA could pick up a stale entry if
the write happened to hit the SBA before the cacheline was flushed
from the cache.
Long term, I think I want to make this a compile time flag.
Developement tree should enable anal pdir checking by default
and Debian can disable it with either a CONFIG option
or one-line patch. fdc/sync options can only negatively affect
performance though I haven't measure how much yet.
If someone can run netperf TCP_RR across gige and compare
-pa1 and -pa2, that would be sufficient.
Cleaned up the use of "fdc" to make sure it's using "kernel"
space id (specify sr0 but maps to sr4-7). It seems a bit fragile
to assume "sr1" gets loaded with KERNEL_SPACE which is how the
code works today.
Tested on 32 and 64-bit SMP kernels on j6k.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove PDC_NARROW from SBA and document history of PDC_NARROW a bit.
It will still show up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
if/ifdef cleanups from Joel Soete.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa2 fix 32-bit support for Astro platforms
o Since my last SBA code change, SBA could allocate more than 1GB of IOVA
space on Astro boxes with more than 1GB of RAM when running 32-bit kernel.
This is bad since IOMMU can only talk to the first 1GB at most.
Kudos to jejb for quickly spotting that bug.
o jejb also noted SBA should *always* reject DMA masks > 32-bits since
DMA-mapping.txt indicates caller should try again with 32-bits.
o off-by-one error when comparing the mask to IOVA space size.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When I originally moved exit_itimers into __exit_signal, that was the only
place where we could reliably know it was the last thread in the group
dying, without races. Since then we've gotten the signal_struct.live
counter, and do_exit can reliably do group-wide cleanup work.
This patch moves the call to do_exit, where it's made without locks. This
avoids the deadlock issues that the old __exit_signal code's comment talks
about, and the one that Oleg found recently with process CPU timers.
[ This replaces e03d13e985, which is why
it was just reverted. ]
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a stupid typo bug in the iSeries hash table code.
When we place a hash PTE in the secondary bucket, instead of setting the
SECONDARY flag bit, as we should, we (redundantly) set the VALID flag.
This was introduced with the patch abolishing bitfields from the hash
table code. Mea culpa, oops. It hasn't been noticed until now because
in practice we don't hit the secondary bucket terribly often.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wrong state emission routines were being called for G550, and
consistent maps weren't correctly mapped...
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While working on 64K pages, I found this little buglet in our
update_mmu_cache() implementation.
The code calls __hash_page() passing it an "access" parameter (the type
of access that triggers the hash) containing the bits _PAGE_RW and
_PAGE_USER of the linux PTE. The latter is useless in this case and the
former is wrong. In fact, if we have a writeable PTE and we pass
_PAGE_RW to hash_page(), it will set _PAGE_DIRTY (since we track dirty
that way, by hash faulting !dirty) which is not what we want.
In fact, the correct fix is to always pass 0. That means that only
read-only or already dirty read write PTEs will be preloaded. The
(hopefully rare) case of a non dirty read write PTE can't be preloaded
this way, it will have to fault in hash_page on the actual access.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a typo in the div128_by_32 function used in the timekeeping
calculations on ppc64. If you look at the code it's quite obvious
that we need (rb + c) rather than (rb + b). The "b" is clearly just a
typo.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes handling of the phy identifiers in mptsas.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
[ split it a pre-2.6.14 portion from Eric's bigger patch ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
From: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Add MASK definitions for DCLK0 and DCLK1
Signed-off-by: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Avoid the possiblity that if the board is using
a 16.9334 or higher crystal with a high PLL
multiplier, then the pll value could overflow
the capability of an int.
Also fix the value types of the intermediate
variables to unsigned int.
Rewrite of patch from Guillaume Gourat
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is legitimate to call tcp_fragment with len == skb->len since
that is done for FIN packets and the FIN flag counts as one byte.
So we should only check for the len > skb->len case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Turns out the problem has nothing to do with use-after-free or double-free.
It's just that we're not clearing the CB area and DCCP unlike TCP uses a CB
format that's incompatible with IP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
icmp_send doesn't use skb->sk at all so even if skb->sk has already
been freed it can't cause crash there (it would've crashed somewhere
else first, e.g., ip_queue_xmit).
I found a double-free on an skb that could explain this though.
dccp_sendmsg and dccp_write_xmit are a little confused as to what
should free the packet when something goes wrong. Sometimes they
both go for the ball and end up in each other's way.
This patch makes dccp_write_xmit always free the packet no matter
what. This makes sense since dccp_transmit_skb which in turn comes
from the fact that ip_queue_xmit always frees the packet.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
David S. Miller <davem@davemloft.net> wrote:
> One thing you can probably do for this bug is to mark data packets
> explicitly somehow, perhaps in the SKB control block DCCP already
> uses for other data. Put some boolean in there, set it true for
> data packets. Then change the test in dccp_transmit_skb() as
> appropriate to test the boolean flag instead of "skb_cloned(skb)".
I agree. In fact we already have that flag, it's called skb->sk.
So here is patch to test that instead of skb_cloned().
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reverts commit 3359b54c8c and
replaces it with a cleaner version that is purely based on page table
operations, so that the synchronization between inode size and hugetlb
mappings becomes moot.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing half of the [PATCH] uml: Fix sysrq-r support for skas mode
We need to remove these (UPT_[DEFG]S) from the read side as well as the
write one - otherwise it simply won't build.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In drivers/acpi/glue.c the address of an integer is cast to the address of
an unsigned long. This breaks on systems where a long is larger than an
int --- for a start the int can be misaligned; for a second the assignment
through the pointer will overwrite part of the next variable.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've gotten a report on lkml, of a possible regression in the MGA DRM in
2.6.14-rc4 (since -rc1), I haven't been able to reproduce it here, but I've
figured out some possible issues in the mga code that were definitely
wrong, some of these are from DRM CVS, the main fix is the agp enable bit
on the old code path still used by everyone.....
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PF_NOFREEZE process flag should not be inherited when a thread is
forked. This patch (as585) removes the flag from the child.
This problem is starting to show up more and more as drivers turn to the
kthread API instead of using kernel_thread(). As a result, their kernel
threads are now children of the kthread worker instead of modprobe, and
they inherit the PF_NOFREEZE flag. This can cause problems during system
suspend; the kernel threads are not getting frozen as they ought to be.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The variable RCS_TAR_IGNORE is used in scripts/packaging/Makefile, but not
exported from the main Makefile, so it's never used.
This results in the rpm targets being very unhappy in quilted trees.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The implementation of __kernel_gettimeofday() in the 32 bits vDSO has a
small bug (a typo actually) that will cause it to lose 1 bit of precision.
Not terribly bad but worth fixing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The main problem fixes is that in certain situations stopping md arrays may
take longer than you expect, or may require multiple attempts. This would
only happen when resync/recovery is happening.
This patch fixes three vaguely related bugs.
1/ The recent change to use kthreads got the setting of the
process name wrong. This fixes it.
2/ The recent change to use kthreads lost the ability for
md threads to be signalled with SIG_KILL. This restores that.
3/ There is a long standing bug in that if:
- An array needs recovery (onto a hot-spare) and
- The recovery is being blocked because some other array being
recovered shares a physical device and
- The recovery thread is killed with SIG_KILL
Then the recovery will appear to have completed with no IO being
done, which can cause data corruption.
This patch makes sure that incomplete recovery will be treated as
incomplete.
Note that any kernel affected by bug 2 will not suffer the problem of bug
3, as the signal can never be delivered. Thus the current 2.6.14-rc
kernels are not susceptible to data corruption. Note also that if arrays
are shutdown (with "mdadm -S" or "raidstop") then the problem doesn't
occur. It only happens if a SIGKILL is independently delivered as done by
'init' when shutting down.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes all spinlocks that can be held during an irq handler to disable
interrupts while the lock is held. Changes spin_[un]lock_irq to use the
irqsave/irqrestore variants for robustness and readability.
In raw1394.c:handle_iso_listen(), don't grab host_info_lock at all -- we're
not accessing host_info_list or host_count, and holding this lock while
trying to tasklet_kill the iso tasklet this can cause an ABBA deadlock if
ohci:dma_rcv_tasklet is running and tries to grab host_info_lock in
raw1394.c:receive_iso. Test program attached reliably deadlocks all SMP
machines I have been able to test without this patch.
Signed-off-by: Andy Wingo <wingo@pobox.com>
Acked-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brice Goglin <Brice.Goglin@ens-lyon.org> reports a printk storm from this
driver. Fix.
Acked-by: David Gibson <hermes@gibson.dropbear.id.au>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hugetlbfs allows truncation of its files (should it?), but hugetlb.c often
forgets that: crashes and misaccounting ensue.
copy_hugetlb_page_range better grab the src page_table_lock since we don't
want to guess what happens if concurrently truncated. unmap_hugepage_range
rss accounting must not assume the full range was mapped. follow_hugetlb_page
must guard with page_table_lock and be prepared to exit early.
Restyle copy_hugetlb_page_range with a for loop like the others there.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oleg Nesterov reported an SMP deadlock. If there is a running timer
tracking a different process's CPU time clock when the process owning
the timer exits, we deadlock on tasklist_lock in posix_cpu_timer_del via
exit_itimers.
That code was using tasklist_lock to check for a race with __exit_signal
being called on the timer-target task and clearing its ->signal.
However, there is actually no such race. __exit_signal will have called
posix_cpu_timers_exit and posix_cpu_timers_exit_group before it does
that. Those will clear those k_itimer's association with the dying
task, so posix_cpu_timer_del will return early and never reach the code
in question.
In addition, posix_cpu_timer_del called from exit_itimers during execve
or directly from timer_delete in the process owning the timer can race
with an exiting timer-target task to cause a double put on timer-target
task struct. Make sure we always access cpu_timers lists with sighand
lock held.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
Machine restart calls cpu_proc_fin() to clean and disable
cache, and turn off interrupts. This patch adds proper
cpu_v6_proc_fin.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hugetlb pages are currently pre-faulted. At the time of mmap of
hugepages, we populate the new PTEs. It is possible that HW has already
cached some of the unused PTEs internally. These stale entries never
get a chance to be purged in existing control flow.
This patch extends the check in page fault code for hugepages. Check if
a faulted address falls with in size for the hugetlb file backing it.
We return VM_FAULT_MINOR for these cases (assuming that the arch
specific page-faulting code purges the stale entry for the archs that
need it).
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
[ This is apparently arguably an ia64 port bug. But the code won't
hurt, and for now it fixes a real problem on some ia64 machines ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
