Make machine_halt() execute a sleep instruction to put the chip in
"stop" mode when the system is halted. This switches off all clocks
except the 32 kHz oscillator, which is needed for the RTC to keep
ticking.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make sure that the flow handler for external interrupts is updated
whenever they type is changed. Also make sure that the defaults
correspond with how the interrupt controller is configured.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The macb driver will probe for the PHY chip and read the mac address
from the MACB registers, so we don't need them in eth_platform_data
anymore.
Since u-boot doesn't currently initialize the MACB registers with the
mac addresses, the tag parsing code is kept but instead of sticking
the information into eth_platform_data, it uses it to initialize
the MACB registers (in case the boot loader didn't do it.) This code
should be unnecessary at some point in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
By moving the ethernet tag parsing to the board-specific code we avoid
the issue of figuring out which device we're supposed to attach the
information to. The board specific code knows this because it's
where the actual devices are instantiated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add platform_device definition and pio init code for the second
ethernet controller in AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rename portmux_set_func to at32_select_periph, add at32_select_gpio
and add flags parameter to specify the initial state of the pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This allows workqueue users to run just their own pending work, rather
than wait for the whole workqueue to finish running. This solves the
deadlock with networking libphy that was due to other workqueue entries
possibly needing a lock that was held by the routine that wanted to
flush its own work.
It's not wonderful: if you absolutely need to synchronize with the work
function having been executed, any user strictly speaking should have
its own completion tracking logic, since when we run things explicitly
by hand, the generic workqueue layer can no longer help us synchronize.
Also, this is strictly only usable for work that has been scheduled
without any delayed timers. You can not mix the new interface with
schedule_delayed_work().
But it's better than what we had currently.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: Incorrect timing computation for PIO5/6
[PATCH] sata_promise: new EH conversion, take 2
[PATCH] libata: let ATA_FLAG_PIO_POLLING use polling pio for ATA_PROT_NODATA
[PATCH] sata_promise: cleanups, take 2
* master.kernel.org:/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (73 commits)
[DLM] Clean up lowcomms
[GFS2] Change gfs2_fsync() to use write_inode_now()
[GFS2] Fix indent in recovery.c
[GFS2] Don't flush everything on fdatasync
[GFS2] Add a comment about reading the super block
[GFS2] Mount problem with the GFS2 code
[GFS2] Remove gfs2_check_acl()
[DLM] fix format warnings in rcom.c and recoverd.c
[GFS2] lock function parameter
[DLM] don't accept replies to old recovery messages
[DLM] fix size of STATUS_REPLY message
[GFS2] fs/gfs2/log.c:log_bmap() fix printk format warning
[DLM] fix add_requestqueue checking nodes list
[GFS2] Fix recursive locking in gfs2_getattr
[GFS2] Fix recursive locking in gfs2_permission
[GFS2] Reduce number of arguments to meta_io.c:getbuf()
[GFS2] Move gfs2_meta_syncfs() into log.c
[GFS2] Fix journal flush problem
[GFS2] mark_inode_dirty after write to stuffed file
[GFS2] Fix glock ordering on inode creation
...
In file included from include/asm/patch.h:14,
from arch/ia64/kernel/patch.c:10:
include/linux/elf.h:375: warning: "struct file" declared inside parameter list
include/linux/elf.h:375: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When using fake NUMA setup, the number of memory nodes can greatly exceed
the number of CPUs. So the current limit in cpuset_common_file_write() is
insufficient.
Signed-off-by: Paul Menage <menage@google.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removes all inline keywords, since the compiler will make static functions
inline when it is appropriate.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Port fix to the off-by-one in find_next_usable_block's memscan from ext2 to
ext3; but it didn't cause a serious problem for ext3 because the additional
ext3_test_allocatable check rescued it from the error.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3_new_blocks has a nice io_error label for setting -EIO, so goto that in
the one place that doesn't already use it.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reservations tree is an rb_tree not a list, so it's less confusing to use
rb_entry() than list_entry() - though they're both just container_of().
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
rsv_end is the last block within the reservation, so alloc_new_reservation
should accept start_block == rsv_end as success.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
grp_goal 0 is a genuine goal (unlike -1), so ext3_try_to_allocate_with_rsv
should treat it as such.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3_new_blocks should reset the reservation window size to 0 when squeezing
the last blocks out of an almost full filesystem, so the retry doesn't skip
any groups with less than half that free, reporting ENOSPC too soon.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build warnings for PROC_FS=n.
drivers/char/ipmi/ipmi_poweroff.c:707: warning: label 'out_err' defined but not used
drivers/char/ipmi/ipmi_msghandler.c:1774: warning: 'ipmb_file_read_proc' defined but not used
drivers/char/ipmi/ipmi_msghandler.c:1790: warning: 'version_file_read_proc' defined but not used
drivers/char/ipmi/ipmi_msghandler.c:1801: warning: 'stat_file_read_proc' defined but not used
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increase the maximum message size a KCS interface supports to the maximum
message size the rest of the driver supports. Some systems really support
messages this big.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IPMI BT subdriver has been patched to survive "long busy" timeouts seen
during firmware upgrades and resets. The patch never returns the HOSED state,
synthesizes response messages with meaningful completion codes, and recovers
gracefully when the hardware finishes the long busy. The subdriver now issues
a "Get BT Capabilities" command and properly uses those results. More
informative completion codes are returned on error from transaction starts;
this logic was propogated to the KCS and SMIC subdrivers. Finally, indent and
other style quirks were normalized.
Signed-off-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change pci_module_init() to the new interface, and check the return code to
avoid warnings and give the user useful information if this fails.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
X86 boards generally use ACPI for the power management interactions with the
BMC. However, non-x86 boards need some help. This patch adds the help for
the Motorola PigeonPoint-based IPMCs.
Signed-off-by: Joseph Barnett <jbarnett@motorola.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability to hot add and remove interfaces in the ipmi_si driver. Any
users who have the device open will get errors if they try to send a message.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure to delay a little in the IPMI poll routine so we can pass in a
timeout time and thus time things out.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the IPMI message handler requested that the interface look for events,
the ipmi_si driver would request flags, see if the event buffer full flag was
set, then request events. It's better to just send the request for events, as
it cuts one message out of the transaction if there happens to be events, and
it will fetch events even if the event buffer was not full.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some commands and operations on a BMC can cause the BMC to "go away" for a
while. This can cause the automatic flag processing and other things of that
nature to timeout and generate annoying logs, or possibly cause other bad
things to happen when in firmware update mode.
Add detection of those commands (cold reset, warm reset, and any firmware
command) and turns off automatic processing for 30 seconds. It also add a
manual override either way.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This modifies the IPMI driver so that a lower-level interface can be
dynamically removed while in use so it can support hot-removal of hardware.
It also adds the ability to specify and dynamically change the IPMI interface
the watchdog timer and the poweroff code use.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass in the sysfs name from the lower-level IPMI driver, as the coming IPMI
serial driver will need that to link properly from the serial device sysfs
directory.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the arbitrary limit of number of IPMI interfaces. This has been tested
with 8 interfaces.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Carol Hebert <cah@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the product id to the driver model platform device name, in addition to
the device id. The IPMI spec does not require that individual BMCs in a
system have unique devices IDs, but it does require that the product id/device
id combination be unique.
This also removes a redundant check and cleans up error handling
when the sysfs registration fails.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Carol Hebert <cah@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow nbd to expose the nbd-client daemon's PID in /sys/block/nbd<x>/pid.
This is helpful for tracking connection status of a device and for
determining which nbd devices are currently in use.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sometimes the kernel prints something interesting while userspace bootup
keeps messages turned off via loglevel. Enable the printing of /all/
kernel messages via the "ignore_loglevel" boot option. Off by default.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hash_lock must only ever be taken with irqs disabled. This happens in
all the important places, except one codepath: register_lock_class(). The
race should trigger rarely because register_lock_class() is quite rare and
single-threaded (happens during init most of the time).
The fix is to disable irqs.
( bug found live in -rt: there preemption is alot more agressive and
preempting with the hash-lock held caused a lockup.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ext[23] mailing list moved from sf.net to vger.kernel.org so update
the MAINTAINERS file.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a nit in ext4_ext_calc_credits_for_insert(). Besides, credits for the
new root are already added in the index split accounting.
Signed-off-by: Johann Lombardi <johann.lombardi@bull.net>
Signed-off-by: Alex Tomas <alex@clusterfs.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the ki_retried member from struct kiocb. I think the idea was
bounced around a while back, but Arnaldo pointed out another reason that we
should dig it up when he pointed out that the last cacheline of struct
kiocb only contains 4 bytes. By removing the debugging member, we save
more than the 8 byte on 64 bit machines.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
io_submit_one assigns ki_left = ki_nbytes = iocb->aio_nbytes, then calls
down to aio_setup_iocb, then to aio_setup_single_vector. In there,
ki_nbytes is reassigned to the same value it got two call stack above it.
There is no need to do so.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The elf note saving code is currently duplicated over several
architectures. This cleanup patch simply adds code to a common file and
then replaces the arch-specific code with calls to the newly added code.
The only drawback with this approach is that s390 doesn't fully support
kexec-on-panic which for that arch leads to introduction of unused code.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Sat, Dec 02, 2006 at 11:47:44PM +0300, Alexey Dobriyan wrote:
> David Binderman compiled 2.6.19 with icc and grepped for "was set but never
> used". Many warnings are on
> http://coderock.org/kj/unused-2.6.19-fs
Heh, the very first line:
fs/exec.c(1465): remark #593: variable "flag" was set but never used
fs/exec.c:
1477 /*
1478 * We cannot trust fsuid as being the "true" uid of the
1479 * process nor do we know its entire history. We only know it
1480 * was tainted so we dump it as root in mode 2.
1481 */
1482 if (mm->dumpable == 2) { /* Setuid core dump mode */
1483 flag = O_EXCL; /* Stop rewrite attacks */
1484 current->fsuid = 0; /* Dump root private */
1485 }
And then filp_open follows with "flag" totally ignored.
(akpm: this restores the code to Alan's original version. Andi's "Support
piping into commands in /proc/sys/kernel/core_pattern" (cset d025c9db) broke
it).
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kerenl.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the contents of the userspace asm/setup.h header consistent on all
architectures:
- export setup.h to userspace on all architectures
- export only COMMAND_LINE_SIZE to userspace
- frv: move COMMAND_LINE_SIZE from param.h
- i386: remove duplicate COMMAND_LINE_SIZE from param.h
- arm:
- export ATAGs to userspace
- change u8/u16/u32 to __u8/__u16/__u32
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Twenty characters in cp936 are not correctly handled. They're all in the
U00 plane. nls_cp936 converts all U00XY to XY but this is not correct for
some characters.(e.g. U00B7 -> A1A4, U00A8 -> A1A7).
This problem is fixed by generating u2c_00 based on all c2u_xx and changing
uni2char() to give U00 plane a special handling. The "â¬"(U20AC,80 in
cp936) is also be handled properly.
Acked-by: Gang Chen <cgdlut@gmail.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- move some file_operations structs into the .rodata section
- move static strings from policy_types[] array into the .rodata section
- fix generic seq_operations usages, so that those structs may be defined
as "const" as well
[akpm@osdl.org: couple of fixes]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
